DeWALT DCF500 Cordless Powered Ratchet Instruction Manual
- June 13, 2024
- Dewalt
Table of Contents
- Instruction Manual
- DCF500
- Intended Use
- Definitions: Safety Alert Symbols and Words
- GENERAL POWER TOOL SAFETY WARNINGS
- Safety Instructions for Ratchet Tools
- Additional Safety Information
- BATTERIES AND CHARGERS
- Battery Pack Cleaning Instructions
- Important Safety Instructions for All Battery Chargers
- Important Charging Notes
- Wall Mounting
- ASSEMBLY AND ADJUSTMENTS
- OPERATION
- MAINTENANCE
- Three-Year Limited Warranty
- References
Instruction Manual
DCF500
*12V Max 1/4″ & 3/8″ Sealed Head Ratchet**
If you have questions or comments, contact us.
1-800-4-DEWALT
(original instructions)
Fig. A
DCF500
(1) Trigger switch
(2) Removable anvil
(3) Forward/reverse switch
(4) Battery release button
(5) Battery pack
(6) Worklight
(7) Main handle
(8) Lock‑off button
(9) Anvil release button
Fig. B
| 75-100% charged
---|---
| 51-74% charged
| < 50% charged
| Pack needs to be charged
Fig. C
Indicators
Charging|
Fully Charged|
Hot/Cold Pack Delay|
Fig. D
Fig. E
Fig. F
Fig. G
WARNING: Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/or
serious injury.
WARNING: To reduce the risk of injury, read the
instruction manual.
Intended Use
This powered ratchet is designed for light duty fastening applications. This
powered ratchet is not a torque wrench.
DO NOT use this tool for tightening fasteners to specified torques. An
independent calibrated torque measurement device such as a torque wrench
should be used when torques are specified.
DO NOT use manually for high torque applications, such as vehicle lug
nuts or bolts. Excessive manually applied torque may damage the tool housing
or mechanism.
DO NOT use under wet conditions or in presence of flammable liquids or
gases.
DO NOT let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury which, if
not avoided, may result in property damage.
(Used without word) Indicates a safety related message.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING: Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1) Work Area Safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) Electrical Safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground
fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the
risk of electric shock.
3) Personal Safety
a) Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, nonskid safety shoes, hard hat, or
hearing protection used for appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position
before connecting to power source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the switch or energizing
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to
become complacent and ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
4) Power Tool Use and Care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source and/ or remove the battery
pack, if detachable, from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for misalignment or binding
of moving parts, breakage of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with
these instructions, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and
grease. Slippery handles and grasping surfaces do not allow for safe
handling and control of the tool in unexpected situations.
5) Battery Tool Use and Care
a) Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects,
like paper clips, coins, keys, nails, screws or other small metal objects,
that can make a connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
e) Do not use a battery pack or tool that is damaged or modified. Damaged
or modified batteries may exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
f) Do not expose a battery pack or tool to fire or excessive temperature.
Exposure to fire or temperature above 265 °F (130 °C) may cause explosion.
g) Follow all charging instructions and do not charge the battery pack or
tool outside the temperature range specified in the instructions. Charging
improperly or at temperatures outside the specified range may damage the
battery and increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
b) Never service damaged battery packs. Service of battery packs should
only be performed by the manufacturer or authorized service providers.
Safety Instructions for Ratchet Tools
- Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the tool “live” and could give the operator an electric shock.
- Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
- Air vents often cover moving parts and should be avoided. Loose clothing, jewelry or long hair can be caught in moving parts.
- Do not operate this tool for long periods of time. Vibration caused by tool action may be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by taking frequent rest periods.
- Accessories and tools get hot during operation. Wear gloves when touching them.
Additional Safety Information
WARNING: Never modify the power tool or any part of it. Damage or personal
injury could result.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
- ANSI Z87.1 eye protection (CAN/CSA Z94.3),
- ANSI S12.6 (S3.19) hearing protection,
- NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
- lead from lead-based paints,
- crystalline silica from bricks and cement and other masonry products, and
- arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
- Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lie on the skin may promote absorption of harmful chemicals. Direct particles away from face and body.
- Use the appropriate dust extractor vacuum to remove the vast majority of static and airborne dust. Failure to remove static and airborne dust could contaminate the working environment or pose an increased health risk to the operator and those in close proximity.
- Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long hair can be caught in moving parts.
CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the battery pack but may be easily knocked over.
The label on your tool may include the following symbols. The symbols and their definitions are as follows:
V …………………….. volts
Hz …………………… hertz
min …………………. minutes
or DC …… direct current
………………….. Class I Construction (grounded)
…/min ………….. per minute
BPM ……………….. beats per minute
IPM ………………… impacts per minute
OPM ……………….. oscillations per minute
RPM ……………….. revolutions per minute
sfpm ………………. surface feet per minute
SPM ……………….. strokes per minute
A …………………….amperes
W …………………… watts
Wh …………………. watt hours
Ah ………………….. amp hours
or AC ……….. alternating current
or AC/DC …. alternating or direct current
…………………. Class II Construction (double insulated)
no ………………….. no load speed
n ……………………. rated speed
PSI ………………….. pounds per square inch
…………………. earthing terminal
………………… safety alert symbol
………………… visible radiation–do not stare into the light
………………… wear respiratory protection
………………… wear eye protection
………………… wear hearing protection
………………… read all documentation
………………… do not expose to rain
BATTERIES AND CHARGERS
The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below and then follow charging procedures outlined. When ordering replacement battery packs, be sure to include the catalog number and voltage.
READ ALL INSTRUCTIONS
Important Safety Instructions for All Battery Packs
WARNING: Read all safety warnings, instructions, and cautionary markings for the battery pack, charger and product. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
-
Do not charge or use the battery pack in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery pack from the charger may ignite the dust or fumes.
-
NEVER force the battery pack into the charger. DO NOT modify the battery pack in any way to fit into a noncompatible charger as battery pack may rupture causing serious personal injury. Consult the chart at the end of this manual for compatibility of batteries and chargers.
-
Charge the battery packs only in DEWALT chargers.
-
DO NOT splash or immerse in water or other liquids.
-
DO NOT allow water or any liquid to enter battery pack.
-
Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 104 °F (40 °C) (such as outside sheds or metal buildings in summer). For best life, store battery packs in a cool, dry location.
NOTE: Do not store the battery packs in a tool with the trigger switch locked on. Never tape the trigger switch in the ON position. -
Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium-ion battery packs are burned.
-
Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 265 °F (130 °C) may cause explosion.
-
Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
-
If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.
-
Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention.
-
Battery liquid may be flammable if exposed to spark or flame.
-
Never attempt to open the battery pack for any reason. If the battery pack case is cracked or damaged, do not insert into the charger. Do not crush, drop or damage the battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (e.g., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to the service center for recycling.
Storage Recommendations
The best storage place is one that is cool and dry, away from direct sunlight and excess heat or cold. Store the fully charged battery pack out of the charger.
Battery Pack Cleaning Instructions
Dirt and grease may be removed from the exterior of the battery pack using a cloth or soft nonmetallic brush. Do not use water or any cleaning solutions.
Fuel Gauge Battery Packs (Fig. B)
Some battery packs include a fuel gauge. When the fuel gauge button is
pressed and held, the LED lights will indicate the approximate level of charge
remaining. This does not indicate tool functionality and is subject to
variation based on product components, temperature, and end-user application.
Transportation
WARNING: Fire hazard. Do not store, carry, or transport the battery pack so that metal objects can contact exposed battery terminals. For example, do not place the battery pack in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, coins, hand tools, etc. When transporting individual battery packs, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit. NOTE: Li-ion battery packs should not be put in checked baggage on airplanes and must be properly protected from short circuits if they are in carryon baggage.
The RBRC® Seal
Please take your spent battery packs to an authorized DEWALT service center or
to your local retailer for recycling. In some areas, it is illegal to place
spent battery packs in the trash. You may also contact your local recycling
center for information on where to drop off the spent battery pack. Do not
place in curbside recycling. For more information visit
www.call2recycle.org or call the toll-free
number in the RBRC® Seal.
RBRC® is a registered trademark of Call 2 Recycle, Inc
Important Safety Instructions for All Battery Chargers
WARNING: Read all safety warnings, instructions, and cautionary markings for the battery pack, charger and product. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
- DO NOT attempt to charge the battery pack with any chargers other than a DEWALT charger. DEWALT chargers and battery packs are specifically designed to work together.
- These chargers are not intended for any uses other than charging DEWALT rechargeable battery packs. Charging other types of battery packs may cause them to overheat and burst, resulting in personal injury, property damage, fire, electric shock or electrocution.
- Do not expose the charger to rain or snow.
- Do not allow water or any liquid to enter charger.
- Pull by the plug rather than the cord when disconnecting the charger. This will reduce the risk of damage to the electric plug and cord.
- Make sure that the cord is located so that it will not be stepped on, tripped over or otherwise subjected to damage or stress.
- Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock or electrocution.
- When operating a charger outdoors, always provide a dry location and use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
- An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the heavier the cord and thus the greater its capacity. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on total length of all extension cords plugged together, and nameplate ampere rating. If in doubt, use the next heavier gauge.
Minimum gauge for Cord sets
Volts
| Total Length of Cord in Feet
(meters)
---|---
120V| 25 (7.6)| 50 (15.2)| 100 (30.5)|
150 (45.7)
Ampere Rating
| American Wire Gauge
More Than|
Not More Than
0
| 6| 18| 16| 16| 14
6| 10| 18| 16| 14|
12
10
| 12| 16| 16| 14| 12
12| 16| 14| 12|
Not Recommended
- Do not place any object on top of the charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing.
- Do not operate the charger with a damaged cord or plug. Have them replaced immediately.
- Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any way. Take it to an authorized service center.
- Do not disassemble the charger; take it to an authorized service center when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
- The charger is designed to operate on standard 120V household electrical power. Do not attempt to use it on any other voltage. This does not apply to the vehicular charger.
- Foreign materials of a conductive nature, such as, but not limited to, grinding dust, metal chips, steel wool, aluminum foil or any buildup of metallic particles should be kept away from the charger cavities and ventilation slots.
- Always unplug the charger from the power supply when there is no battery pack in the cavity.
Charging a Battery (Fig. C)
-
Plug the charger into an appropriate outlet.
-
Insert and fully seat battery pack (5). The red charging light(s) will continuously blink while charging.
-
Charging is complete when the red charging light(s) remain(s) continuously ON. Battery pack can be left in charger or removed.
WARNING: Only charge batteries in air temperature over 40 ° F (4.5 ° C) and below 104 ° F (40 ° C). -
Charger will not charge a faulty battery pack, which may be indicated by the charging light(s) staying OFF. Take charger and battery pack to an authorized service center if light(s) stay(s) OFF.
NOTE: Refer to label near charging light(s) on charger for blink patterns. Older chargers may have additional information and/or may not have a yellow indicator light.
NOTE: To remove the battery pack, some chargers require the battery pack release button (4) to be pressed.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too cold, it
automatically starts a Hot/Cold Pack Delay, suspending charging until the
battery pack has reached an appropriate temperature. The charger then
automatically switches to the pack charging mode. This feature ensures maximum
battery pack life.
A cold battery pack may charge at a slower rate than a warm battery pack.
The hot/cold pack delay will be indicated by the red light(s) continuing to
blink but with the yellow light continuously ON. Once the battery pack has
reached an appropriate temperature, the yellow light will turn OFF and the
charger will resume the charging procedure.
DCB118 and DCB1112 Chargers
The DCB118 and DCB1112 chargers are equipped with an internal fan designed
to cool the battery pack. The fan will turn on automatically when the battery
pack needs to be cooled.
Never operate the charger if the fan does not operate properly or if
ventilation slots are blocked. Do not permit foreign objects to enter the
interior of the charger.
Electronic Protection System
Li-ion tools are designed with an Electronic Protection System that will protect the battery pack against overloading, overheating or deep discharge. The tool will automatically turn off and the battery pack will need to be recharged.
Important Charging Notes
-
Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65 ° F – 75 ° F (18 ° C – 24 ° C). DO NOT charge when the battery pack is below 40 ° F (4.5 ° C), or above 104 ° F (40 ° C). This is important and will prevent serious damage to the battery pack.
-
The charger and battery pack may become warm to the touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed or an uninsulated trailer.
-
If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other appliance;
b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights;
c. If charging problems persist, take the tool, battery pack and charger to your local service center. -
You may charge a partially used pack whenever you desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft nonmetallic brush. Do not use water or any cleaning solutions.
Wall Mounting
Some DEWALT chargers are designed to be wall mountable or to sit upright on a table or work surface. If wall mounting, locate the charger within reach of an electrical outlet, and away from a corner or other obstructions which may impede air flow. Use the back of the charger as a template for the location of the mounting screws on the wall. Mount the charger securely using drywall screws (purchased separately) at least 1″ (25.4 mm) long, with a screw head diameter of 0.28-0.35″ (7-9 mm), screwed into wood to an optimal depth leaving approximately 7/32″ (5.5 mm) of the screw exposed. Align the slots on the back of the charger with the exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental startup can cause injury.
Anvil (Fig. F)
CAUTION: Inspect anvil prior to use. Missing or damaged items should be replaced before use.
To install the anvil , align with the anvil receptacle. Press the anvil
(2) into the tool. To install an accessory on the anvil, align the
accessory with the anvil (2). Press the accessory onto the anvil.
To remove the anvil , push the release button (9) on the backside of
the anvil to remove it. To remove an accessory, pull the accessory off the
anvil (2).
OPERATION
WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental startup can cause injury.
Installing and Removing the Battery Pack (Fig. D)
WARNING: Ensure the tool/appliance is in the off position before inserting
the battery pack.
NOTE: For best results, make sure your battery pack is fully charged.
- To install the battery pack (14) into the tool handle, align the battery pack with the rails inside the tool’s handle and slide it into the handle until the battery pack is firmly seated in the tool and ensure that it does not disengage.
- To remove the battery pack from the tool, press the battery pack release button (4) and firmly pull the battery pack out of the tool handle. Insert it into the charger as described in the charger section of this manual.
Proper Hand Position (Fig. E)
WARNING: To reduce the risk of serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of serious personal injury, ALWAYS hold
securely in anticipation of a sudden reaction.
WARNING: Ratchet may stall (if overloaded or improperly used) causing a
twist. Always expect the stall. Grip the ratchet firmly to control the
twisting action and prevent loss of control which could cause personal injury.
Proper hand position requires one hand on the main handle (7) as shown to control the twisting action of the ratchet.
Variable Speed Trigger (Fig. A)
The tool is turned on and off by pulling and releasing the variable speed trigger (1). The farther the trigger is depressed, the higher the speed of the tool. The anvil will stop as soon as the trigger switch is fully released.
Forward/Reverse Dial (Fig. A, G)
A forward/reverse dial (3) determines the rotational direction of the tool.
- To select forward rotation (clockwise), release the trigger and rotate the forward/reverse dial on the head of the tool in a counterclockwise direction.
- To select reverse rotation (counterclockwise), release the trigger and rotate the forward/reverse dial on the head of the tool in a clockwise direction.
NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on start up. This is normal and does not indicate a problem.
Lock-off Button (Fig. A)
To lock the tool, slide the lock-off button (8) to the locked position. When the lock-off button is in the locked position, the tool is locked and the trigger switch (1) cannot be pulled.
Worklight (Fig. A)
The worklight (6) is activated when the trigger switch (1) is depressed, and will automatically turn off 20 seconds after the trigger switch is released. If the trigger switch remains depressed, the worklight will remain on.
NOTE: The worklight is for lighting the immediate work surface and is not intended to be used as a flashlight.
Usage (Fig. A, E)
WARNING: To reduce the risk of serious personal injury, turn unit off and
remove the battery pack before making any adjustments or removing/ installing
attachments or accessories. An accidental startup can cause injury.
WARNING: The ratchet may stall if overloaded causing a sudden twist.
Always expect the tool to twist. Grip the ratchet firmly to control the
twisting action and avoid possible personal injury.
CAUTION: Ensure fastener and/or system will withstand the level of torque
generated by the tool. Excessive torque may cause breakage and possible
personal injury.
Cat #
| RPM| Ft.-Lbs.| Nm
---|---|---|---
DCF500| 0-450| 50 (Max.)|
67.79 (Max.)
-
Install the appropriate anvil (2) (3/8″, 1/4″, or 1/4″ Quick Change Hex) on the tool.
a. If an anvil is installed on the tool, push the release button (9) on the backside of the tool and remove the anvil.
b. To install an anvil, push the desired anvil into the tool until it is secure. -
Keep the tool pointed straight at the fastener.
-
Consider the intended operation and select either forward or reverse rotation.
-
Press variable speed trigger switch (1) to start operation.
-
Release variable speed trigger switch (1) to stop operation.
-
If the ratchet stalls, release the variable speed trigger switch (1) immediately. Do not press the variable speed trigger switch (1) on and off in an attempt to start a stalled ratchet. Doing so can damage the tool.
-
The ratchet can also be used manually for breaking free stubborn fasteners or snugging by releasing the trigger and applying the torque by hand.
NOTE: Excessive manual torque may damage the included anvils.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn unit off and remove the battery pack before making any adjustments or removing/ installing attachments or accessories. An accidental startup can cause injury.
Your DEWALT power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at
least once a week. To minimize the risk of eye injury, always wear ANSI Z87.1
approved eye protection when performing this procedure.
WARNING: Never use solvents or other harsh chemicals for cleaning the
nonmetallic parts of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened only with water and mild
soap. Never let any liquid get inside the tool; never immerse any part of the
tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this product could be hazardous. To reduce the risk of injury, only DEWALT recommended accessories should be used with this product.
Recommended accessories for use with your product are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact DEWALT. Call 1-800-4-DEWALT (1-800-433-9258) or visit our website: www.dewalt.com.
Repairs
The charger and batteries are not serviceable. There are no serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement, when applicable) should be performed by a factory service center or an authorized service center. Always use identical replacement parts.
Register Online
- WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty service in case there is a problem with your product.
- CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft, your registration of ownership will serve as your proof of purchase.
- FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event a safety notification is required under the Federal Consumer Safety Act.
- Register online at www.dewalt.com.
Three-Year Limited Warranty
For warranty terms, go to
https://www.dewalt.com/support/warranty.
To request a written copy of the warranty terms, contact: Customer Service at
DeWALT Industrial Tool Co., 701 East Joppa Road, Towson, MD 21286 or call
1-800-4-DeWALT (1-800-433-9258).
LATIN AMERICA: This warranty does not apply to products sold in Latin
America. For products sold in Latin America, see country‑specific warranty
information contained in the packaging, call the local company or see website
for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible
or are missing, call 1-800-4-DeWALT
(1-800-433-9258) for a free
replacement.
Compatible battery packs and chargers
*12V Max Li‑Ion**
| Battery Packs| DCB120, DCB122, DCB124, DCB124G, DCB126, DCB126G, DCB127,
DCB127G
---|---|---
Chargers| DCB103, DCB104, DCB107, DCB112, DCB113, DCB115, DCB1102, DCB1104
- Maximum initial battery voltage (measured without a workload) is 12 volts. Nominal voltage is 10.8.
WARNING: Use of any other battery packs may create a risk of injury and fire.
DeWALT Industrial Tool Co. 701 East Joppa Road, Towson, MD 21286
Copyright © 2023
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme, the “D” shaped air intake grill, the array of pyramids on the handgrip, the kit box configuration, and the array of lozenge-shaped humps on the surface of the tool.
N894353
05/23
References
- Call2Recycle | Leading the Charge For Battery Recycling
- DEWALT® Power Tools Official Site | Guaranteed Tough®
- DEWALT® Power Tools Official Site | Guaranteed Tough®
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>