support Sonoff LBS D1 Wi-Fi Smart Dimmer Switch User Manual
- June 4, 2024
- support
Table of Contents
LBS D1 Wi-Fi Smart Dimmer Switch
User Manual
operating Instruction
-
Power off
To avoid electric shocks, please consult the dealer or a qualified professional for help when installing and repairing! Please do not touch the switch during use. -
Wiring instruction
The device can only connect incandescent light bulbs and dimmable LED lights.
Make sure the neutral wire and live wire connection are correct. -
Download the APPhttp://app.coolkit.cc/dl.html
-
Power on
After powering on, the device will enter the quick pairing mode (Touch) during the first use. The connected light enters the “breathing mode”.
**** It will exit the quick pairing mode (Touch) if the device is not paired within 3mins. If you need to enter this mode again, please power off and restart the device until the connected light enters the “breathing mode”. -
Add the device
**** Tap “+” and select “ Quick Pairing ”, then operate following the prompt on the app.
Pairing method for the device and SONOFF RM433 remote controller:
Short press any button on the RM433 remote controller within 5s after powering
on until you hear “Bi”, which indicates all buttons are paired successfully.
**** The RM433 remote controller is not included, please purchase it
separately.
RM433 Introduction
| Buttons | Functions |
|---|---|
| On | |
| Off | |
| Short press for the low brightness, long press to turn down the brightness | |
| Short press for the medium brightness, long press to turn down the |
brightness
| Short press for the higher brightness, and long press to turn up the
brightness
| Short press for the high brightness, long press to turn up the brightness
| Long press for 5s until you hear “Beep Beep” and release, then the remote
controller is cleared successfully. After clearing code is completed, if you
need to use it, short press any button within 5s after powering on again and
you will hear“Beep”, which indicates the remote controller is paired
successfully.
| Long press for 5s until the connected light enters the breathing mode, which
indicates the device enters quick pairing mode (Touch), then you can add the
light on the eWeLink APP. In quick pairing mode,
you can short press any button on the remote controller to exit this mode.
Specifications
| Model | D1 |
|---|---|
| Input | 100-240V-AC-50/60Hz |
| Output | 100-240V-AC-50/60Hz |
| Light Load | Incandescent:200W LED:150W |
| Operating systems | Android & iOS |
| Wi-Fi | IEEE 802.11 b/g/n 2.4GHz |
| RF | 433.92MHz |
| Working temperature | -10℃~40℃ |
| Material | PC V0 |
| Dimension | 62x47x32.5mm |
Features
D1 is a Wi-Fi smart dimmer switch that is used to adjust the light brightness and set various atmospheres for your room. You can remotely turn on/off light of your home anywhere, schedule it on/off, or share it with your family to control together.
Factory Reset
Turn on and off 3 times on repeatedly or delete the connected light on eWeLink APP until it enters “breathing mode”, then the device is reset successfully and enters quick pairing mode (Touch).
**** Please reset the device to factory defaults if you want to use other Wi- Fi networks, then reconnect the network.
FCC Warning
Changes or modifications not expressly approved by the party responsible for
compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance20cm between the radiator & your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio
equipment type D1 is in compliance with Directive 2014/53/EU.The full text of
the EU declaration of conformity is available at the following internet
address:
https://sonoff.tech/usermanuals
TX Frequency:
WiFi: 2412-2472MHz
RX Frequency:
WiFi: 2412-2472MHz
SRD: 433.92MHz
Output Power: 11.52dBm(802.11b), 11.33dBm(802.11g), 11.07dBm(802.11n20
Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDG8, Lianhua Industrial Park, Shenzhen
GD, China ZIP code: 518000 Website: sonoff. tech
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>