ALL SOLAR CENTRAL SP010 Solar Water Pump Kit Instructions
- June 13, 2024
- ALL SOLAR CENTRAL
Table of Contents
SP010 Solar Water Pump Kit
SP010 Solar Water Pump Kit Instructions
By All Solar Central
www.allsolarcentral.com
Thank you from the entire ASC family for purchasing an ASC solar product!
Please read this entire booklet before assembly.
Package contents:
1 x Water Pump with 16 ft. Cable
1 x LED Light Ring with 16 ft. Cable
1 x Battery Control Box
2 x Solar Panel with 6.5 ft. Cable
2 x Solar Panel Bracket
4 x Extension Tube
2 x Ground Spike
1 x Set of Fountain Nozzles
Notes: If there is any damage to the product or missing parts, please
contact us at 1-626-582-8898 or
www.allsolarcentral.com/contactus
Assembly Steps:
-
Connect the bracket, tubes and spike together. Then attach the solar panel to the bracket. Slide the holding bracket into the inside lip of the top half of the solar panel frame. The bracket holds the weight of the solar panel. The solar panel can be adjusted for optimal sunlight by using the wingnut. Please see the diagram.
-
Insert the spike into the ground. Position the solar panel so it’s facing south (in northern hemisphere) as much as possible to maximize daylight hours. It is important to angle the solar panel to face the sun when the sun is at its highest point. Ensure the solar panel is not shaded by trees, shrubs or buildings.
-
Connect the Solar Panel, LED Light, and Pump to the Battery Control Box (See diagram below:)
IMPORTANT!!
Slightly twist the connectors when connecting to make sure the rubber seals are fully in the grooves. -
The assembled Solar Pump should look like this:
BATTERY CONTROL BOX OPERATION
Note: The LED light is designed to work at night only
The solar pump is designed mainly for use during summer hours, but it will
also work in spring and fall as long as the sunlight conditions are good
enough in your region. And the new Winter Mode will extend battery life time
during the winter. The pump’s performance depends on the orientation of the
solar panel towards the sun (see section 2) and the strength on sunlight.
This ASC solar pump kit comes with three operation modes: Continuously On,
2-4hrs Timer, and Winter mode.
a. CONTINUOUSLY ON MODE: This mode works best if you want to maximize the
pump’s daily usage. Press [Power] button, the top indicator light [On] will be
on. The pump will run continuously until the battery runs out of power. The
pump will automatically restart when the battery is recharged under proper
sunlight.
b. DAILY TIMER MODE: This mode works best if you want the pump run at the
same time every day (The time you start the mode). Press [Timer] button
repeatedly until the indicator light [2hrs], [3hrs] or [4hrs] is lit – the
pump will run for 2, 3, or 4 hours and shut down (in standby) for 22, 21, or
20 hours. This setting will repeat at the same time every day. You can reset
the pump’s daily start up time by switching it to a new desired time using
this mode.
c. WINTER MODE: This mode works best in winter or poor weather. Press
[Winter] button, the top indicator light [Pulse] will be on. The pump will run
for 20 seconds in every 60 seconds. It is recommended to use this mode to
extend battery life time in winter or poor weather.
PUMP FLOW CONTROL button: Use this button to adjust the water flow rate.
Press [Flow Rate] repeatedly to adjust the water flow rate (total 3 levels).
Notes: Higher water flow rate will consume more power and reduce the battery
life time.
LOW BATTERY light: The [Low Bat.] indicator light will be blinking when
the battery is low, and pump/LED light will shut down shortly to protect the
battery. The [Low Bat.] indicator light will turn off until the battery is
recharged.
PERFORMANCE OF THE PUMP
The performance of the pump depends on the orientation of the solar panel towards the sun and the sunlight strength. In order to achieve max performance, please make sure the panel is facing in the direction of the sun. A solar panel positioned in the shade or in poor weather will not maximize the charge. This models pump performance will depend on the battery power level. The pump will not work if battery power is too low.
PUMP MAINTENANCE
If you find the pump starts losing power or stops working, please clean the
pump filter and impeller with clean water.
1. PUMP CASE
(2) IMPELLER COVER 3. IMPELLER 4. PUMP 5. FILTER
BATTERY REPLACEMENT
If properly maintained this solar pump has been designed to run for many years. The Lead-acid battery does have a limited life span and might need to be replaced after 18-24 months of use. If the battery appears less efficient, please try to boost charge it. To do this, leave the system off for 2 to 3 sunny days to allow fully charge to the battery. It is recommended to do this occasionally to maximize battery life time.
To replace battery, please follow these steps:
a. Remove the screws from the Battery Box
b. Remove the lid and control panel from the battery box slightly
c. Disconnect the battery connectors, then remove and replace the old battery.
NOTES: Please make sure to connect the new battery correctly: Red for +
and Black for – . Only original battery should be used for replacement as
other alternatives may be incompatible and may damage the control panel and
will void the warranty. For parts, lease go to www.allsolarcentral.com
TROUBLE SHOOTING
- Check to see if the solar panel, pump and led light are connected properly
- Check to see if the solar panel is correctly positioned facing the sun. Please ensure the solar panel is not in the shade or obstructed by trees, shrubs or a building (see step 2).
- Check if [low bat.] light is on. If so, this indicates that the battery power is low. Switch off the pump and leave the solar panel charging under direct sunlight for 1 or 2 days.
- CHARGING TIPS: Press button [Power] to turn off the system. All indicator lights should be off. All solar power will now be used to charge the battery.
- Check water level and make sure the pump is fully submerged in water
- Check to see if the pump filter/impeller is blocked by debris
- Check to see if the fountain tubing is blocked by kinks or obstructions
- Check the pump. It may be “air locked”. Turn the pump on/off switch several times to clear any air that may have been trapped.
TECHANICAL DATA
- Max. Water Flow: 1500LPH
- Max. Water Lift: 300CM
- Max. Fountain Height: 160CM
- Working Voltage: DC15V – DC18V
- Pump Working Power: 6.6W – 11.2W
- Protection Grade of Pump: IP68
- Solar Panel: 2 x 10.0W; 18V; 0.555A
- Solar Panel Size: 2 x 350x285x18mm
- Protection Grade of Panel: IP44
- Battery: Lead-acid 12V/5AH
- Protection Grade of Battery Box: IP44
- LED Light Working Voltage: DC12V
- LED Light Working Power: 0.12W
- Protection Grade of LED Light: IP68
WINTER PROTECTION
Indoor storage is recommended during winter months. Normal operating
temperature is between 50 and 113 °F. Battery can be recharged at temperatures
between 32 and 113 °F.
IMPORTANT!!
In order to keep your battery healthy during long storage times, please make
sure the battery is fully recharged before storing. To do this, turn off the
pump by pressing button [Power] and charge the battery for 1 or 2 sunny days.
See Step 9 –Charging Tips
PROPOSITION 65 WARNING:
Battery posts, terminals and related accessories contain lead and lead
compounds, chemicals known to the State of California to cause cancer and
reproductive harm. Wash hands after handling. For more information go to
https://www.p65warnings.ca.gov/
BATTERY DISPOSE:
Never dispose of batteries in the garbage. Disposal of batteries in the
garbage is unlawful under state and federal environmental laws and
regulations. Always take used batteries to your local battery-recycling
center.
Please visit www.allsolarcentral.com for
more products and offers.
http://www.allsolarcentral.com
References
- AllSolarCentral: Eco-Friendly Solar Powered Water Pump and Fountains – Allsolarcentral.com
- Contact Us – Allsolarcentral.com
- Manual-Hub.com – Free PDF manuals!
- p65warnings.ca.gov/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>