GHOST AXS1 3 Button Standard Remote Transmitter User Guide

: June 13, 2024
: Ghost

Table of Contents

GHOST AXS1 3 Button Standard Remote Transmitter
Product Information
Product Usage Instructions
PROGRAMMING AND REMOTE TRANSMITTER OVERVIEW
GENERATING A NEW TRANSMITTING KEY CODE
FCC STATEMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GHOST AXS1 3 Button Standard Remote Transmitter

Product Information

The product is a standard remote transmitter used for controllinggates. It has 3 buttons and an LED light. The remote comes in two versions: Remote A (Training) and Remote B (Learning). The remote is used to activate Gate 1 or Gate 2. It also has a learn button for programming additional remotes. The LED/alarm button sequence is used for programming the remote to the gate controller. The remote uses GhostCodeTM signal to transmit commands to the gate controller.

Product Usage Instructions

Programming Remote to Gate Controller

Press and hold the LEARN XMTR button on the gate system controller.
Press and hold button 1 or button 2 on Remote A (Training) for 2 seconds.
Release the button on Remote A. The gate controller alarm will beep or the gate will begin moving.
No alarm sounds, and the LEARN XMTR LED on the main controller is on. Press and release the button on Remote A to test the transmitter.

Adding an Additional Remote Transmitter

Press and hold the button on Remote B (Learning) for at least 3 seconds.
Press and hold button 1 or button 2 on Remote A (Teaching Remote).
Press and release the button on Remote B (Learning Remote). The LED on Remote B will indicate successful programming.

Cloning / Copying Button 1’s ID to Button 2

Press and hold the LEARN button on the remote for at least 3 seconds.
Release the LEARN button. The remote is now in Learning Mode.
Press and release Button 1. The LED should start flashing rapidly, indicating that the remote is sending Button 1’s ID.
Press and release Button 2. The LED should turn off, indicating that Button 1’s ID is accepted by Button 2. Both buttons should now work the same gate.

Cloning / Copying Button 2’s ID to Button 1

Press and hold the LEARN button on the remote for at least 3 seconds.
Release the LEARN button. The remote is now in Learning Mode.
Press and release Button 2. The LED should start flashing rapidly, indicating that the remote is sending Button 2’s ID.
Press and release Button 1. The LED should turn off, indicating that Button 2’s ID is accepted by Button 1. Both buttons should now work the same gate.

PROGRAMMING AND REMOTE TRANSMITTER OVERVIEW

All GHOST CONTROLS® remote transmitters must be programmed before they will operate the Gate Opener System so that the safety and security of your system is maintained.

NOTE: REMOTES A & B MUST BE TOUCHING AND ORIENTED AS SHOWN TO PROGRAM REMOTE B FROM REMOTE A.

PROGRAMMING REMOTE TO GATE CONTROLLER

STEP| LED/ALARM BEFORE PRESSING| BUTTON(S) SEQUENCE TO PRESS| LED/ALARM AFTER PRESSING| DESCRIPTION
1| | Press & hold LEARN XMTR button on gate system controller| Gate alarm sounds and LEARN XMTR LED on system controller stay| Places gate controller into Learn Remote mode for 10 seconds. NOTE-The gate system controller will exit the Learn Remote mode after 10 seconds and return to normal operation if there is no valid remote transmitter signal received.
2| Gate controller LED is| Press & hold for 2 seconds| Gate controller alarm beeps or gate begins moving| Programs this button into memory.
3| | Release the | LEARN XMTR LED goes| The new transmitter’s ID has been saved into the memory of the main system controller.
4| No alarm sounds, LEARN XMTR LED on main controller is LED on remote is| Press and release the button| ****

Transmitter LED on when button is depressed

| Test the transmitter button you just programmed. LED on transmitter turns on only when button is depressed to indicate it is transmitting GhostCodeTM signal to gate controller. Each press of this remote button will cycle the gate as follows: OPEN-STOP-CLOSE-STOP- OPEN. The LED will be flashing rapidly when the transmitter is transmitting. Maximum transmitting time is approximately 20 seconds to save battery life.
ADD AN ADDITIONAL REMOTE TRANSMITTER TO CONTROL THE GATE
1| | Press & hold the on Remote B (Learning) for at least 3 seconds or until the LED goes | ****

Remote LED is

| This process assumes that Remote A (Teaching Remote) is ALREADY capable of controlling the gate. This puts Remote B (Learning Remote) into Learning Mode.
2| | Press & hold on Remote A, the Teaching

Remote.

| LEDs on both Teaching and Learning Remote are| Remote A (Teaching Remote) is in Teach Mode, and Remote B (Learning Remote) is in Learn Mode.
3| | Press & release on Remote B, the Learning Remote.| Remote LED goes| Indicates that the Learning Remote button (Remote B) pressed in this step is now programmed to operate the same gate as the Teaching Remote (Remote A).
CLONE / COPY BUTTON 1’S ID TO BUTTON 2’S (BUTTON 1 ALREADY CONTROLS THE GATE)
STEP| NOTE| BUTTON(S) SEQUENCE TO PRESS| LED/ALARM AFTER PRESSING| DESCRIPTION
1| | Press & hold LEARN button on Remote for AT LEAST 3 seconds until the LED turns on| ****

LED on Remote stays

| ****

Places remote transmitter into Learning mode.

LED on Remote stays

| ****

Places remote transmitter into Learning mode.

GENERATING A NEW TRANSMITTING KEY CODE

CAUTION: Please READ and PROCEED with CAUTION

Each GHOST CONTROLS® remote transmitter has a unique key code sequence. Once a new key sequence is generated, the previous key code is lost. The new key code will need to be programmed or “learned” into the gate opener to control the gate.

STEP| LED/ALARM BEFORE PRESSING| BUTTON(S) SEQUENCE TO PRESS| LED/ALARM AFTER PRESSING| DESCRIPTION
---|---|---|---|---

1

| | Press & hold simultaneously for 10 seconds on Remote until the LED goes|

LED on Remote goes

| ****

Tells the remote transmitter (Remote B) that you are going to generate a new code. Step 2 & 3 must be completed within 5 seconds while the LED is lit.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation.

WARNING

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced technician for help.

WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov

WARNING: This product contains a Button or Coin Cell Battery. A swallowed Button or Coin Cell Battery can cause internal chemical burns in as little as two hours and lead to death. Dispose of used batteries immediately. Keep new and used batteries away from childern. If you think batteries might have been swallowed or placed inside any part of the body,seek immediate medical attention.

www.GhostControls.com

Made in China
©2023 GHOST CONTROLS®