Narcissus QN-M866 Electric Knife Sharpener User Manual

Narcissus Electric Knife Sharpener
User Manual

QN-M866 Electric Knife Sharpener

Please read this manual in detail prior to first use.
In case of any quality issues, please contact us at support@narcissus.com. We can provide a free replacement or other satisfactory services.

Important Precautions

1. Never operate the sharpener from the back side. Make sure the sharpening slots are on your right before using.
   

2. Each sharpening slot has two sides. Grind the knife obliquely against the sloping side rather than the vertical side.

3. Only pull the knife backward. Never push it forward.

4. Sharpen the knife with the Crude slots and remove burrs with the Fine slots.

5. Every knife needs to be sharpened many times to form the edge during the first sharpening; otherwise, the knife will even become duller.

6. Pull the knife smoothly when sharpening; the extra force will only reduce the life of the sharpener or knife.

7. Never interrupt or stop the motion of the blade when sharpening.

8. The sharpener is not suitable for grinding ceramic or curved knives.
   

9. Test the knife with paper or food, never with your body.

10. Prevent children from using or touching to avoid accidents.

11. Use the sharpener with a specific voltage of 110-240V~50/60Hz.

12. Remove grease and water from knives before sharpening. Don’t add water, oil, or other substances when sharpening.

13. The sharpener sometimes gives off a pungent smell. Also, there will be sparks when sharpening. Kindly rest assured that this is normal.

Instructions for Sharpen Common Knives

This instruction applies to the most common kitchen knives, including chef, slicing, santoku, utility, boning, carving, brisket, butcher, cleaver, sushi, and nakiri knives.

1. Preparation:

2. Place the sharpener in a stable position. Make sure the sharpening slots are on your right.

3. Clean and dry the knives.

4. Connect the power supply and the sharpener with the adapter, then turn on the switch located on the left of the sharpener.

5. Sharpen the Knife:

6. Insert the knife obliquely into one of the Crude sharpening slots.
   Pull back about 1in/s until the blade completely passes through the grinding wheel.

7. Transfer the knife to another Crude sharpening slot. Following the same method explained above, sharpen the other side of the blade.

8. Repeat the two steps above depending on the knives:
   First sharpening of the knife: 10-20 pairs of alternating pulls.
   Thin & sharp knives: 2-5 pairs of alternating pulls.
   Thin & dull knives: 5-10 pairs of alternating pulls.
   Thick & sharp knives: 5-10 pairs of alternating pulls.
   Thick & dull knives: 10-20 pairs of alternating pulls.
   High carbon content knives may require twice as many times.

9. Remove the Burrs:

10. Insert the knife obliquely into one of the Fine sharpening slots.
    Pull back about 2in/s until the blade completely passes through the grinding wheel.

11. Transfer the knife to another Fine sharpening slot. Following the same method explained above, remove burrs on the other side of the blade.

12. Repeat the two steps above once or several times to make the blade smooth enough.

Precautions:

1. Never operate the sharpener from the back side.
2. Grind the knife obliquely against the sloping side.
3. Only pull the knife backward. Never push it forward.
4. Paring, pocket, and hunting knives can also be sharpened this way; however, they have a section that cannot be sharpened. Due to the product structure, we have no way to solve the problem. If that causes annoyance, please contact us for a free return.

Instructions for Sharpen Serrated Knives

This instruction applies to serrated kitchen knives, including bread, steak, and tomato knives, but not to serrated non-kitchen knives such as saws.
Most bread, steak, and tomato knives only have serrations on the left. Hence, it is required to only grind the serrated side. Grinding the other side will dull the knife.
The following instructions apply only to the left serrated knives. If it is a right or bilateral serrated knife, please adjust flexibly.

1. Preparation:
2. Place the sharpener in a stable position. Make sure the sharpening slots are on your right.
3. Clean and dry the knives.
4. Connect the power supply and the sharpener with the adapter, then turn on the switch located on the left of the sharpener.
5. Sharpen the Knife:
6. Insert the knife obliquely into the right Crude sharpening slot. Pull back about 1in/s until the blade completely passes through the grinding wheel.
7. Repeat twice.
8. Remove the Burrs:
9. Insert the knife obliquely into the right Fine sharpening slots. Pull back about 2in/s until the blade completely passes through the grinding wheel.
10. Repeat twice.

Precautions:

1. Never operate the sharpener from the back side.
2. Grind the knife obliquely against the sloping side.
3. Only pull the knife backward. Never push it forward.
4. Use cardboard to test the sharpness of the serrated knife, not paper.
5. Don’t grind the side without serrations; otherwise, the knife will be dull.

Instructions for Grinding Scissors

The sharpener can only be used to repair scissors for cutting paper or cloth, such as multipurpose, kitchen, sewing and office scissors, not for other shears such as poultry, garden and hair shears.

1. Learn about Scissors :
2. Find the Cutting Side: Each foot of the scissors has several sides. We only need to grind the Cutting Side, not the other sides.
3. Check the Rivet: Scissors with loose rivets cannot cut things, even with sharp blades. In this situation, tighten the rivet with a hammer or other method before grinding the scissors.
4. Preparation:
5. Place the sharpener in a stable position. Make sure the sharpening slots are on your right.
6. Clean and dry the scissors.
7. Connect the power supply and the sharpener with the adapter, then turn on the switch located on the left of the sharpener.
8. Grind Scissors & Remove Burrs :
9. Separate the two feet of the scissors.
10. Move the Cutting Side of the scissors to approach the rotating scissors grinding wheel. Pull the scissors against the grinding wheel about 1in/s until the blade fully passes through. Repeat 2 to 5 times.
11. Follow the step above to grind another blade of the scissors.
12. Open and close the scissors several times to remove the burrs on the blades.

Precautions:

1. Never operate the sharpener from the back side.
2. Only pull the scissors backward. Never push them forward.
3. Don’t use the knife-sharpening slots to grind scissors, and don’t use the scissors-grinding slot to sharpen knives.

Troubleshooting

Pull instead of pus’ g fo rward.
Not Enough Grinding| Grind more times. Drag slowly.
Unsuitable Knives| Not for ceramic or curved knives.
Not Working| No Power| Check the power supply.
Product Problem| Contact us for a free replacement.
Blocked While Sharpening| The Knife is Curved| Flatten the knife before sharpening.
Wheel Deviation| Contact us for a free replacement.
Can’t Sharpen the Scissors| Scissors’ Rivet Loose| Tighten the rivet.
Blade Chipped| Over-grinding| Don’t let the knife stand still.
Asymmetric Blade| Different Intensity| Don’t squeeze the wheel hard.
Knife Scratch| Debris in the Slots| Clean the debris.

Please contact us via email at support@narcissus.tech if the problem persists or if any other issues occur.

Cleaning and Maintenance

1. Open the crumb bin at the bottom and wipe the crumbs after every one hour of use.

2. Unplug before cleaning.

3. Wipe the surface and slots with a clean soft cloth.

4. DO NOT immerse the sharpener in water for cleaning.

5. Store the sharpener in a dry and ventilated place.

Warranty

Thank you for choosing and supporting Narcissus.
Narcissus provides all customers with 12 months of free replacement services. In case of any quality issues, please contact us via email at support@narcissus.tech.
We will provide you with a satisfying solution.
Thank you for understanding!

Specification

Model: QN-M866-2
Rated Voltage: 110-240V~50/60Hz
Rated Power: 10W
Gross Weight: 1.60 lbs
Package Size: 10.84.04.2 in
Official email: support@narcissus.tech
Manufacturer: Foshan Taobei Technology Co., Ltd.
Address: No.1 Guizhou Avenue West, Foshan, Guangdong, China
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>