LG HMH018WA Dehumidifier Instruction Manual

LG HMH018WA Dehumidifier

Product Information

Specifications:

• Brand: LG
• Model: HMH018WA
• Type: Dehumidifier

Product Usage Instructions

Setting Up the Dehumidifier:

1. Place the dehumidifier in a location where the air can circulate freely.
2. Ensure the unit is plugged into a power source.
3. Adjust the settings to your desired humidity level using the control panel.

Cleaning and Maintenance:

1. Regularly clean the air filter to ensure optimal performance.
2. Empty the water tank when full to prevent overflow.
3. Inspect the unit for any dust or debris buildup and clean as needed.

Troubleshooting:

If you encounter any issues with the dehumidifier, refer to the owner’s manual for troubleshooting steps or contact customer support.

FAQs

• Q: Where can I find genuine replacement parts for my LG HMH018WA dehumidifier?
  • A: Genuine replacement parts for the LG HMH018WA dehumidifier can be purchased from Appliance Factory Parts.
• Q: How often should I clean the air filter of the dehumidifier?
  • A: It is recommended to clean the air filter of the dehumidifier every 2-4 weeks to maintain efficiency.

Installation

1. Installation of Indoor, Outdoor unit

1. Selection of the best location
   1. Indoor unit
   • There should not be any heat source or steam near the unit.
   • There should not be any obstacles to prevent the
   air circulation.
   • A place where air circulation in the room will be good.
   • A place where drainage can be easily obtained.
   • A place where noise prevention is taken into con-
   sideration.
   • Do not install the unit near the door way.
   • Ensure the spaces indicated by arrows from the
   wall, ceiling, fence, or other obstacles.
   2. Outdoor unit
   • If an awning is built over the unit to prevent direct sunlight or rain exposure, be careful that heat radi- ation from the condenser is not restricted.
   • There should not be any animals or plants which could be affected by hot air discharged.
   • Ensure the spaces indicated by arrows from the
   wall, ceiling, fence, or other obstacles.

2. Indoor Unit Installation
   To prevent i rom he word ion strong and solid enough
   1. Mount the installation plate on the wall with
   four Type “A” screws.
   (if mounting the unit on the concrete wall, consider
   using anchor bolts.)
   • Always mount the installation plate horizontally by
   aligning the marking-off line by means of the
   thread and a level.

2. Piping and Drainage of Indoor Unit

1. Preparation of Pipings
   1. Cut the pipes and the cable.
   • Use the accessory piping kit or the pipes pur- chased locally.
   • Measure the distance between the indoor and the outdoor unit.
   • Cut the pipes a little longer than measured dis-
   tance.
   • Cut the cable 1.5m longer than the length of the pipe.
   2. Remove burrs.
   • Remove burrs from cut edges of pipes.
   • Turn the pipe end toward down to avoid the metal powder entering the pipe.
   Caution:
   age.
   If burrs are not removed, they may cause a gas leak-
   3. Flaring the pipes.
   • Insert the flare nuts, mounted on the connection
   ports of both indoor and outdoor unit, onto the copper pipes. Some gas may leak, when the flare nuts are removed from the indoor unit, as some gas is charged to prevent the inside of the pipe from rusting.
   • Fit the copper pipe end into the Bar of flare tool about 0.5~1.0mm higher. (See illustration)
   • Flare the pipe ends.
   4. Tape the flaring portion to protect it from the
   dust or damages.

2. Connection of Pipings
   1. Remove the indoor tubing with Drain hose from
   the hole
   • Remove tubing holder and pull the tubing out of
   the chassis.
   2. Replace the tubing holder into original position.
   For right rear piping
   3. Packwate tubing and the drain hose straight
   4. Insert the connecting cable into the indoor unit
   through the piping hole.
   • Do not connect the cable to the indoor unit.
   • Make a small loop with the cable for easy connection later.
   Cooling Model
   Heat Pump Model
   18K
   124K, 26K, 28K
   5. Tape the tubing, drain hose and the connecting cable. Be sure that drain hose locates at the lowest side of the bundle. Locating at the upper side can be a reason that drain water overflows
   drain pan inside the unit.

6. Indoor unit installation
• Hook the indoor unit onto the upper portion of installation plate. (Engage the two hooks of the
rear top of the indoor unit with the upper edge of the installation plate.)
Ensure the hooks are properly seated on the
installation plate by moving it left and right.
7. Connecting the pipings to the indoor unit.
• Align the center of the pipings and sufficiently tighten the flare nut with fingers.
• Finally, tighten the flare nut with torque wrench until the wrench clicks.
When tightening the flare nut with torque wrench, ensure the direction for tightening follows the
arrow on the wrench.

Pipe Size
Liquid Side (1/4)
Liquid Side(3/8)
Gas Side(1/2″)
Gas Side(5/8″)
Torque
1.8kg-m
42kg-m
5.5kg-m
6.6kg-m
8. Wrap the insulation material around the connecting portion.
CAUTION: Take care to arrange the pipings, drain
so sor inserting it ito the indoor unit
and refixing the tubing holder easily.

References

• Repair Your Grill: Shop Replacement Parts for 24,880 Models
• Lg Dehumidifier Parts - Select From 224 Models

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>