Shelly E26-E27 Duo Smart Bulb User Guide
- June 13, 2024
- Shelly
Table of Contents
SHELLY DUO SMART BULB
USER AND SAFETY GUIDE
Read before use
This document contains important technical and safety information about the device, its safety use and installation.
CAUTION! Before beginning the installation, please read this guide and any other documents accompanying the device carefully and completely. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of the law or refusal of legal and/or commercial guarantee (if any). Allterco Robotics EOOD is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.
Product Introduction
Shelly® is a line of innovative microprocessor-managed devices, which allow remote control of electric circuits through a mobile phone, tablet, PC, or home automation system. Shelly® devices can work standalone in a local Wi-Fi network or they can also be operated through cloud home automation services. Shelly Cloud is a service that can be accessed using either Android or iOS mobile application, or with any internet browser at https://home.shelly.cloud/. Shelly® devices can be accessed, controlled and monitored remotely from any place where the User has internet connectivity, as long as the devices are connected to a Wi- Fi router and the Internet. Shelly® devices have embedded Web Interface accessible at http://192.168.33.1 when connected directly to the device access point, or at the device IP address on the local Wi-Fi network. The embedded Web Interface can be used to monitor and control the device, as well as adjust its settings. Shelly® devices can communicate directly with other Wi-Fi devices through HTTP protocol. An API is provided by Allterco Robotics EOOD. For more information, please visit: https://shelly- api-docs.shelly.cloud/#shelly-family-overview. Shelly® devices are delivered with factory-installed firmware. If firmware updates are necessary to keep the devices in conformity, including security updates, Allterco Robotics EOOD will provide the updates free of charge through the device embedded Web Interface or Shelly Mobile Application, where the information about the current firmware version is available. The choice to install or not the device firmware updates is user’s sole responsibility. Allterco Robotics EOOD shall not be liable for any lack of conformity of the device caused by failure of the user to install the provided updates in a timely manner.
Control your home with your voice
Shelly® devices are compatible with Amazon Alexa and Google Home supported functionalities. Please see our step-by-step guide on: https://shelly.cloud/support/compatibility/.
Installation Instructions
The Shelly DUO ( WW/CW or RGBW model ) smart Wi-Fi LED bulb by Allterco
Robotics is intended to be installed into a standard light socket (E27/E26 or
GU10) in order to change the white temperature or color (depending on model)
and to dim the light. Shelly may work as a standalone device or as an
accessory to a home automation controller.
CAUTION! Danger of electrocution. Installing the device to the power grid
has to be performed with caution.
CAUTION! Danger of electrocution. Before installing or removing the
Device please check that the breakers are turned off and there is no voltage
at the light socket contacts. This can be done with a phase tester or
multimeter.
CAUTION! Use the Device only with power grid which comply with all
applicable local regulations. Short circuit in the power grid connected to the
Device may damage the Device.
CAUTION! Please check the working voltage of the device and the supplied
voltage of your power grid before installing the device! Installing the device
to a non recommended power supply may lead to malfunction, danger to your life
or violation of the law. Allterco Robotics is not responsible for any loss or
damage in case of incorrect installation or operation of this device.
CAUTION! Please handle with care! The Shelly® DUO is FRAGILE!
Specification
Power supply|
110-240 VAC; 50/60Hz
---|---
Socket|
E26/E27
|
GU10
Power Rating|
9 W
|
5 W
Brightness|
Up to 800 lm
|
Up to 400 lm
Color Temperature|
WW/CW (2700K-6500K); RGBW
Beam Angle|
190°
|
36°
Working temperature|
From -15°C to 40°C
Radio protocol|
Wi-Fi 802.11 b/g/n
Frequency|
2412 – 2472 MHz
Max – 2483.5 MHz;
Max RF output power|
12.64 dBm
Operational range (depending on local construction)|
up to 30 m outdoors
up to 15 m indoors
Dimensions|
60×122 mm
|
50×73 mm
Electrical consumption|
< 1 W
Initial Inclusion
If you choose to use the Device with the Shelly Cloud mobile application and
Shelly Cloud service, instructions on how to connect the Device to the Cloud
and control it through the Shelly App can be found in the “App Guide”.
The Shelly Mobile Application and Shelly Cloud service are not conditions for
the Device to function properly. This Device can be used stand-alone or with
various other home automation platforms and protocols.
CAUTION! Do not allow children to play with the buttons/ switches
connected to the Device. Keep the Devices for remote control of Shelly (mobile
phones, tablets, PCs) away from children.
Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly
DUO is in compliance with Directive 2014/53/EU, 2014/35/EU, 2014/30/EU,
2011/65/EU. The full text of the EU declaration of conformity is available at
the following internet address: https://shelly.cloud/knowledge-base/devices
/shelly-bulb-rgbw/ Manufacturer: Allterco Robotics EOOD
Address: Bulgaria, Sofia, 1407, 103 Cherni vrah Blvd.
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Web: http://www.shelly.cloud
Changes in the contact data are published by the Manufacturer at the official
website of the Device: http://www.shelly.cloud
All rights to trademark Shelly® , and other intellectual rights associated
with this Device belong to Allterco Robotics EOOD.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>