Schneider Electric EBIOTPGW EcoStruxure Building-IoT Gateway Installation Guide

: June 13, 2024
: Schneider Electric

Table of Contents

Schneider Electric EBIOTPGW EcoStruxure Building-IoT Gateway
Product Information
Part Numbers
Documents / Resources

Schneider Electric EBIOTPGW EcoStruxure Building-IoT Gateway

Product Information

The EcoStruxure Building-IoT Gateway is a multi-protocol gateway designed for commercial facilities and building installations. It can simultaneously receive data from multiple wireless protocols and has built-in radios for direct communication with sensors in the IoT Sensor Solution product family. Multiple gateways can be installed to support thousands of sensors.

Regulatory Compliance and Safety Information

Electrical equipment should only be installed, operated, serviced, and maintained by qualified personnel. Schneider Electric assumes no responsibility for any consequences arising from the use of this material. Please read these instructions and all relevant information before attempting to install the product.

Dimensions

Width: 149.3 mm (5.9 inches)
Height: 125 mm (4.9 inches)
Depth: 40 mm (1.6 inches)
Weight: 185 g (0.4 lb)

Installation Restrictions

NOTICE: Installing the Device

For models with the LTE option: Install the antenna.
Use adapted screws to install the gateway on the wall.
Power on the gateway using the power adapter or Power over Ethernet (PoE). The green LED will turn on solid to indicate the device is operational. Otherwise, press the on/off button to power it up.

Connections and Buttons

The EcoStruxure Building-IoT Gateway features various connection
ports and buttons:

DC Jack
SIM Card LTE
USB 2.0 Holder
Antenna
1GBE RJ45
CAN
On/Off Button
Reset Button
POE Button

Part Numbers

Product Code / Model Number: EBIOTPGW
AC/DC Power supply (to be ordered separately)
LTE Antenna (To be ordered separately for models supporting LTE)

General Specifications

Maximum number of supported devices: IoT Sensor Solution sensors – 200
Material: Plastic casing with internal antenna for Wi-Fi/Bluetooth. One SMA port for LTE.
Mechanical Dimensions: 150L x 85W x 40H mm (5.9L x 3.3W x 1.6H in)
Weight: 185 g (0.4 lb)
Electrical Power: DC 9 – 36 V, Power over Ethernet (PoE) PD
IEEE802.3AF, 5W peak power
Hardware: RAM – 1GB DDR4, Storage capacity – 8GB eMMC
Connectors: 1 x RS485 (option), 1 x CAN (option), 1 x USB 2.0
Connector (Type-A), 1 x DC 9V – 36V power supply
Wireless Connectivity:
- Communication protocol: 2.4 GHz, Sensor Network supporting Mesh Technology
- Antenna type: Omnidirectional, internal
- WiFi Interface: 2.4GHz/5GHz b/g/n/ac module
- Antenna type: Omnidirectional, internal
- FCC ID: 2BA24LBEE5HY1MW, IC: 12107A-LBEE5HY1MW
- LTE: 1 x LTE Cat 4 Worldwide + GPS (with fallback on 3G/2G)
- FCC ID: XMR201903EG25G, IC: 10224A-201903EG25G
Installation: Wall-mounted, installation equipment included (mounting tape, screws, installation instructions)

Addendum – California Proposition 65 Warning Statement for California Residents

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm, and Bisphenol A (BPA), which is known to the State of California to cause birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.

The IoT Gateway is a multi-protocol gateway that can simultaneously receive data from multiple wireless protocols. It is designed for commercial facilities and building installations. The Gateway has built-in radios to allow for direct communication with sensors in the IoT Sensor Solution product family. Multiple gateways can be installed to support thousands of sensors.

Regulatory Compliance and Safety Information

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.
Carefully read these instructions and all information relevant to this product before trying to install it. See the list of technical literature.

Dimensions

Schneider-Electric-EBIOTPGW-EcoStruxure-Building-IoT-Gatewa--
fig-1

Installation Restrictions

NOTICE REDUCED DEVICE PERFORMANCE

This device is for indoor use only and is not suitable for wet locations.
Do not install the device close to an exterior window.
When replacing a device, install the new device in the same position and direction as the replaced device.
Failure to follow these instructions can result in reduced device performance.

Installing the Device

For models with LTE option: Install the antennaa.
Use adapted screws to install the gateway on the wall.
Power on the gateway using the power adaptera or Power over Ethernet (PoE).

The green LED will turn on solid to indicate the device is operational. Otherwise, press the on/off button to power it up.

Connections and Buttons

Part Numbers

Product Code/model number: EBIOTPGW Part Numbers
- EcoStuxure Building-IoT Gateway EBIOTPGW
AC/DC Power supply (to be ordered separately) ICP12-120-1000DSD4
- LTE Antenna (To be ordered separately for models supporting LTE) AN00010

General Specifications

Maximum number of supported devices
- IoT Sensor Solution sensors 200

Material

Enclosure
- Plastic casing with internal antenna for Wi-Fi/ Bluetooth. One SMA port for LTE.
Mechanical
- Dimensions
150L x 85W x 40H mm (5.9L x 3.3W x 1.6H in)
- Weight
185 g (0.4 lb)
- Electrical
Power
- DC 9 – 36 V
Power over Ethernet (PoE) PD IEEE802.3AF
- 5W peak power
Hardware
- RAM
1GB DDR4
- Storage capacity
8GB eMMC

Connectors

1 x RS485 (option)
- 1 x CAN (option)
1 x USB 2.0 Connector, Type-A 1 x DC 9V – 36V power supply
- Wireless connectivity
Communication protocol
- 2.4 GHz, Sensor Network supporting Mesh Technology
Antenna type Omnidirectional, internal.
- WiFi Interface
2.4GHz/5GHz b/g/n/ac module
- Antenna type Omnidirectional, internal.
FCC ID: 2BA24LBEE5HY1MW, IC: 12107A-LBEE5HY1MW
- LTE 1 x LTE Cat 4 Worldwide + GPS (with fallback on 3G/2G) FCC ID: XMR201903EG25G IC: 10224A-201903EG25G

Optional AC/DC Power supply

Model ICP12-120-1000D
- Input AC 100-240V
Output DC 12V-1A @ 40°C
- Environment Environmental conditions Indoor use only
Ambient temperature, operating
- 0 to 50 °C (32 to 122 °F)
Ambient temperature, storage
- -20 to 65 °C (-4 to 149 °F)
Humidity
- 0 to 95 % (non-condensing)
Installation Mounting Wall-mounted
- Installation equipment included
Mounting tape, screws, and installation instructions

FCC

ID: 2BATG-EBIOTPGW, IC: 30486-EBIOTPGW

Addendum – California Proposition 65 Warning Statement for California Residents
WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm, and Bisphenol A (BPA), which is known to the State of California to cause birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Regulatory Notices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, this equipment should be installed and operated with a minimum distance 20 cm (7.9 inches) between the antenna and your body during normal operation. Users must follow the specific operating instructions for satisfying RF exposure compliance.
This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.9 inches) between the radiator and any part of your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This radio transmitter 30486-EBIOTPGW has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Under Innovation, Science, and Economic Development regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Approved Antenna Type:
Maximum gain: 3 dBi
Antenna type: FPC (Flexible Printed Circuit)
Radiation pattern: Omni-Directional
Impedance: 50 Ohm
Connector type: U.FL
© 2023 Schneider Electric. All rights reserved. Trademarks and registered trademarks are the property of their respective owners www.se.com/buildings

Documents / Resources

| Schneider Electric EBIOTPGW EcoStruxure Building-IoT Gateway [pdf] Installation Guide
EBIOTPGW EcoStruxure Building-IoT Gateway, EBIOTPGW, EcoStruxure Building-IoT Gateway, Building-IoT Gateway, Gateway
---|---