Antari AF-4 Special Effects Fan User Manual

June 13, 2024
Antari

Special Effects Fan
User Manual
Antari AF-4 Special Effects Fan

Introduction

Please read all the user manual before operating the machine, and place the manual where the user can refer to it at all time. The manual includes how to install and operate the machine under safe condition and explain all the labels printed on the machine. If you encounter any problem, contact your local Antari dealer for assistant immediately.

Safety Information

DANGER If the danger is not avoided, it will cause death or serious injury
WARNING If the warning is not heeded, it can cause death or serious injury.
CAUTION If the precaution is not taken, it may cause minor or moderate

injury.

DANGER

  • Must connect the machine to the correct rated voltage or it might lead to an electrical shock or a burn and may cause serious consequences.
  • Must connect the machine to a protected circuit and ensure it is properly grounded to avoid the risk of electrocution. For grounding instruction, please refer to Appendix I on page 15.
  • Do not operate the machine with a bundled power cord, it could lead to a fire hazard.
  • Do not use the fan in an environment full of flammable gas, susceptible to water or powder. Keep away from any fire and heat sources.
  • When operating the machine, do not point at people, animals, or fire.

WARNING

  • Please operate the machine on a flat, level hard and well ventilated surface area, reserve at least 50cm space around the machine and make sure there is no flammable gas or material nearby.
  • Do not disassemble, repair or modify the machine, it may cause damages, malfunction, risk of electrical shock or result in fire.
  • The machine can only be operated by adults or professionals, is not intended for use by person with reduced physical sensory, mental capabilities, or lack of experience and knowledge including children.
  • Do not leave the machine running unattended, make sure all powers are off when leaving.
  • Children should be supervised to ensure that they do not play with the machine.
  • Do not use the machine upside down or tilt it, it might cause damages or malfunction.
  • Never allow any object or part of your body to enter path of the fan blades to prevent any injury or damages Do not spray the fan with any liquid including cleaner and insecticide to avoid injury or damages.

CAUTION

  • Keep the machine dry at all time. The machine is not waterproof, do not expose the machine to water, rain, or moisture environment.
  • Please make sure the power outlet is not damaged or loose before plug in the power cord.
  • If the power cord is damaged, it must be replaced by Antari or its local dealers, otherwise the warranty will be void.
  • The machine is for indoor use only.
  • Do not operate the machine in any area with unstable voltage.
  • If you experience strange sound or malfunction, turn off the power and unplug the power cord immediately and contact your local Antari dealer for assistant.
  • Do not contact any moving part.
  • Only use accessories recommended or sold by Antari.
  • Please make sure the power is off when not using the machine and unplug the power cord if not intend to use for a long period of time.
  • To disconnect, turn all controls to the off position, then remove plug from outlet.
  • Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
  • Unplug from outlet before servicing or cleaning.
  • Ensure that curtain, clothing, cables or other items cannot be suck into the fan.
  • Do not operate the machine with a damaged cord or plug, or after the machine malfunctions or is dropped or damaged in any manner. Return machine to the nearest authorized service facility for examination, repair, or electrical or mechanical adjustment.
  • After a period of operation, abnormal noise and uneven air volume may appear because of dust blocking airflow. It will disappear after cleaning the air inlet and outlet.

Before operating the machine, please read all warning labels on the machine, description as below:

WARNING!
Do not allow any object or part of your body get near the protection grill while operating the fan.
Operate fan only with adult supervision.
Do not use fan without protection grill.
Do not use the fan in damp environment.

Package Contents & Inspection

Immediately upon receiving the machine, carefully unpack the carton, check the content to ensure it is the correct model and all parts are included. If any part appears to be damaged or missing during transportation, please contact your local dealer and return with original package for inspection.
3.1 Package Contents

AF-4 AF-4R
1 x AF-4 Special Effects Fan 1 x AF-4R Special Effects Fan
1 x User Manual or Scan QR Code on the Machine 1 x WTR-20 Wireless Remote
1 x User Manual or Scan QR Code on the Machine

3.2 Optional Accessories

Item Code Description
Z-3 Cable Remote
WTR-20 Wireless Remote (W-2 Wireless Transmitter and W-2 Wireless Receiver)

Machine Details

Antari AF-4 Special Effects Fan - Machine Details

01. Fan Inlet 06. Cable Remote Connector
02. Fuse 07. Fan Outlet
03. Expansion Slot 08. Adjusting Knob
04. LCD Screen 09. Handle
05. XLR 5-Pin Connector (DMX) 10. Stand

 Technical Label Information

Please read the technical label information on the back of the machine before operating it.

Antari AF-4 Special Effects Fan - Label

1. Model Name| 5. Breaker/Fuse
2. Input Voltage| 6. QR CODE for User Manual
3. Frequency| 7. Serial No.
4. Rated Power|

Setting and Manual Operation

Step 1. Place the machine on a flat, level hard and well ventilated surface area and reserve at least 50cm open space around the machine, and make sure there is no flammable gas or material nearby;
Step 2. Plug the machine to the power outlet. Please read the technical label on the back of the machine and make sure the power outlet has the correct rated voltage for the machine;
Step 3. Turn on the power, when the LCD displays “Ready”, now the machine is ready for operation;
Step 4. To start, press [VOLUME] button and you can adjust the fan speed by pressing [UP/DOWN] and to stop, please press [STOP] button;
Step 5. To turn off the power, please make sure the machine is not operating. If you will not use the machine a long period of time, please unplug the power cord.

Control Settings

AF-4/AF-4R Special Effects Fan can be operated in the following modes. The machine can only accept 1 type of signal at a time.

  • Manual
  • Timer
  • DMX512
  •  Wireless
  • Cable Remote

7.1 Control Panel Description

AF-4 /AF-4R Special Effect Fan can be operated with the onboard digital control interface.

Button Operating Method Action
MENU Press Scroll through setting menu
TIMER Press Activate Timer function
VOLUME Press Activate Volume function
UP/DOWN Press Increase/Decrease Value
STOP Press Deactivate Timer/Volume function & Confirm/Leave Setting Menu

7.2 Menu Options Description

Options Description
Interval 180 seconds Set Interval between 1-180s
Duration 120 seconds Set Duration between 1-120s
Volume Out 100 % Set Volume Output from 20-100%
Timer Out 100 % Set Timer Output from 20-100%
DMX512 Add.512 Set DMX Address from 1-512
Wireless OFF Turn ON/OFF for Wireless Control
Quick Start OFF Turn ON/OFF Run Last Setting
Back Lite Always On/Auto Off (30s)

DMX Connection

8.1 DMX Connector Pin Assignment
The machine has a XLR 5-Pin for DMX connection. The diagram below indicates pin assignment information.

Pin Function
1 Ground
2 Data-
3 Data+
4 NA
5 NA

** There is a protection cap on DMX IN, please remove it with your finger before operation.

8.2 DMX Setting

Channel Mode Channel DMX Value Range Function
1 1 0 – 5 Off
6 – 255 Fan 20 – 100%

Z-3 Cable Remote (Optional)

Z-3 Cable Remote is an optional accessory for AF-4/AF-4R Special Effects Fan, please see instruction below;

  1. Plug the cable remote to the connector on the back of the machine, red indicator light on (Power);
  2. Press the switch (Orange Indicator Light on); turn the knob to adjust the output of the fan;
  3. Press the switch (Orange Indicator Light Off), or turn the knob to far left to turn off the fan.
    ** If you encounter any problem, please contact your local Antari dealer for assistant

WTR-20 Wireless Remote (Optional)

WTR-20 Wireless Remote is an optional accessory for AF-4 Special Effects Fan, it included a W-2 wireless transmitter and a W-2 wireless receiver. If you already purchased the wireless model, it’s ready to use. If you purchase the WTR-20 Wireless Remote afterwards, please follow the instruction below. If you encounter any problem, please contact your local Antari dealer for assistant.

10.1 W-2 Wireless Transmitter & Receiver

  • Battery:27A 12V
  • Effective Range:The effective range is approximately 50m, depends on actual condition, it may vary.
  • If effective range is significantly shorter, please change battery.
  • W-2 wireless transmitter has 4 buttons, each function as follow:
Button Function
[A] Start
[B] Stop
--- ---
[C] Increase Fan Speed
[D] Decrease Fan Speed

10.2 W-2 Wireless Receiver Installation

If you purchased the WTR-20 Wireless Remote afterwards, please follow the instructions below to install the receiver. If you encounter any problem, please contact your local Antari dealer for assistant.

Antari AF-4 Special Effects Fan - Graph

  1. Please see graph 1, remove the cover from the pointed place;
  2. You will see a white cable like graph 2, pull it out and connect to the W-2 wireless receiver;
  3. Screw it back to the machine like graph 3 and follow the instruction on 10.3 for pairing.

10.3 Pair & Unpair
Each receiver can pair up to 5 transmitters, please follow the steps below to pair or unpair;

Step 1. Go to [MENU]→[Wireless], turn on wireless function;
Step 2. Power off the machine first then press and hold [DOWN] button, then turn on the power (still press & hold the [DOWN] button until screen shows below;
Step 3. Press [UP] to start pairing and press any button on W-2 transmitter to complete the pairing;
Step 4. Please repeat Step 2. to pair multiple transmitters
Step 5. To unpair, repeat Step 2. and press [DOWN] to unpair.

Service and Maintenance

DANGER Disconnect the power cord before starting maintenance operation!

  • Always keep the machine clean.
  • Can use an air compressor, a vacuum or a soft brush to remove the dust on the machine.
  • Can use a slightly damp cloth to clean the casing.
  • Before store the machine, please make sure the machine is completely cool down to avoid moisture inside the machine causing malfunction.
  • It is recommended to run the machine at least once a month in order to maintain its best performance and output condition.
  • Excessive dust will reduce the performance and cause overheat.

Fuse Specification
120V=T2.0A 250V
240V=T1.0A 250V

Technical Specifications

| AF-4/AF-4R
---|---
Rated Voltage| US Model : AC 100-120V, 50/60Hz 1.0A
EU Model : AC 220-240V, 50/60Hz 0.5A
Rated Power| 100W
Ambient Temp. Range| 0°C – 40°C (32°F – 104°F)
Air Flow| 1187 CFM (AC 110V/60Hz)、1035 CFM (AC 220V/60Hz)
Fan Speed| 1242 – 1480 rpm (AC 110V/60Hz)、1175 – 1,289 rpm (AC 220V/60Hz)
Noise Level| 68.5 dB (Max. Output)
Control Methods| Manual、Timer、DMX512、Wireless (Optional)、Cable Remote (Optional)
Interface| XLR 5-Pin Connector (DMX)
DMX Channel| 1 Channel
Included Accessories| N/A
Optional Accessories| Z-3 Cable Remote、WTR-20 Wireless Remote
Dimension| L 353 W 377 H 517 mm (L 13.90 W 14.84 H 20.35 inch)
Weight| 9.00 kg (19.84 lbs.)

Warranty Disclaimer

We guarantee the merchandise manufactured by us to be free from defect in material and workmanship for a period of one year. Our obligation and liability under this warranty shall be restricted to repair or replacement at our factory or local authorized dealer. We assume no liability of the products that are improperly used or used for any purpose other than that for which they are specially designed. This warranty shall not apply to any merchandise which has been repaired, altered or assembled outside our factory in any way so as in our judgment to affect its performance, nor which has been subjected to misuse, negligence, or accident nor to any merchandise operated contrary to our printed instructions. We will not allow or be liable of any loss or any damages of any kind in connection with the use, sale, or repair of any merchandise purchased from us.

Machine Dimension

Antari AF-4 Special Effects Fan - Machine Dimension

Appendix I – Grounding Instruction

This appliance must be grounded. In the event of malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipmentgrounding conductor. If repair or replacement of the cord or plug is necessary, do not connect the equipmentgrounding conductor to a live terminal. Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This appliance is for use on a nominal 120V circuit, and has a grounding plug that looks like the plug illustrated in sketch A in Figure. A temporary adaptor, which looks like the adaptor illustrated in sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet can be installed by a qualified electrician.
The green colored rigid ear, lug, and the like, extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by the metal screw.

Antari AF-4 Special Effects Fan - Grounding

Antari AF-4 Special Effects Fan - icon © 2023 Antari Lighting and Effects Ltd.

Documents / Resources

| Antari AF-4 Special Effects Fan [pdf] User Manual
AF-4, AF-4R, AF-4 Special Effects Fan, Special Effects Fan, Effects Fan, Fan
---|---

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals