Machineart Moto 2005-2012 R1200GS Puig Touring Windscreen Installation Guide

Machineart Moto 2005-2012 R1200GS Puig Touring Windscreen

Product Information

• Fits all 2005-2012 R1200GS/A + 2013 R1200 Adventure motorcycles.
• Parts: Slipscreen (uses stock fasteners).
• Tools Required: T25 Torx Driver, 10mm box end wrench.

For installation on a GS Adventure, additional parts are required (listed below).

• Available from your BMW dealer:
  • Locking Disk Left (part #46637707221),
  • Locking Disk Right (part #46637707222),
  • Covering Left (part #46637673913),
  • Covering Right (part #46637673914),
  • Exterior Bushing (2 required, part #46637676997),
  • Bushing Inside (2 required, part #46637676996).
• Contact information: Specialized Products for BMW twins,
• Phone : 908.996.7210,
• Website : www.machineartmoto.com.

Product Usage Instructions

1. Remove the mounting hardware from your stock screen (GS) and reinstall it on the SlipScreen. For ADV models, refer to the NOTE below.
2. Install the stock Locking Disc & Covering on the SlipScreen in the same manner they were removed from your stock windshield. Ensure that the Locking Disc & Covering are placed correctly (marked L & R).
3. Position the SlipScreen and secure it by installing two front screws and nuts.
4. Insert the side mounting hardware – Sleeve and Clamping Bolt – and adjust the SlipScreen to the desired angle. Hand tighten the Clamping Bolt.
5. Tighten the 10mm nut on the inside to secure the SlipScreen firmly.

NOTE : For installation on a GS Adventure model, you will require additional parts listed above. The Adventure  Clamping Bolts (longer versions of part #3) can be reused. For further assistance or inquiries, please contact Specialized Products for BMW twins at the provided phone number or visit their website.

Installation Guide
Fits all 2005-2012 R1200GS/A + 2013 R1200 Adventure

Parts:

• Slipscreen
• Uses stock fasteners

Tools Required

• T25 Torx Driver
• 10mm box end wrench

INSTALLATION

1. Remove mounting hardware from your stock screen (GS) and re-install on the SlipScreen.(For ADV see NOTE).
   • Install the stock Locking Disc & Covering in the same way they were removed from your stock windshield. Locking Disc & Covering are marked L & R.
2. Position screen and install two front screws and nuts.
3. Insert the side mounting hardware – Sleeve and Clamping Bolt – and tilt the SlipScreen to the desired angle. Hand tighten the Clamping Bolt. Tighten the 10mm nut on the inside.

NOTE: For installation on a GS Adventure, you will require parts for the standard GS listed below. The Adventure Clamping Bolts (longer versions of part #3 above) may be re-used. The following are available from your BMW dealer:

Part numbers

• 46637707221 Locking Disk Left
• 46637707222 Locking Disk Right
• 46637673913 Covering Left
• 46637673914 Covering Right
• 46637676997 Exterior Bushing
• 46637676996 Bushing Inside

WARNING AND DISCLAIMER :
All parts manufactured, designed or sold by Machineart Moto (“MaMo”) should be installed by a qualified motorcycle technician. The risk of injury is increased by improper installation or misuse of equipment. MaMo’s customers must exercise good judgment in the use, control, alteration, part selection and installation, and maintenance of their motorcycles. In the event of a possible defect in material or design, or any other defect in a part manufactured, designed or sold by MaMo, the responsibility of MaMo is limited to a refund of the purchase price or the replacement of the part if MaMo determines the part to be defective, and subject to MaMo’s inspection of the part within thirty (30) days from the date of purchase. (Note: any attempted repairs or modifications made to MaMo products will void this limited warranty). MaMo, under no circumstances will be responsible for incidental and/or consequential damages, property damage, personal injury damage, or damage, injury, cost or expense of any kind or nature whatsoever except as provided by law. MaMo makes no other warranty, express or implied, including without limitation any warranties of merchantability and fitness for a particular purpose.

Specialized Products for BMW twins  908.996.7210
www.machineartmoto.com

References

• Protection Products for BMW & Adventure Touring Motorcycles – MachineartMoto

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>