BeefEater BF3310 Glass-Door Tropicalised Refrigerator User Manual
- June 13, 2024
- BeefEater
Table of Contents
- BeefEater BF3310 Glass-Door Tropicalised Refrigerator
- Product Usage Instructions
- Important Safety Instructionsions
- Before Using For the First Time
- Preparation
- Cleaning
- Electronic Control
- Operation of the controller
- Technical Information
- Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BeefEater BF3310 Glass-Door Tropicalised Refrigerator
Product Information:
BeefEater Glass-Door Tropicalised Refrigerator
The BeefEater Glass-Door Tropicalised Refrigerator is a commercial-style fridge designed for outdoor use. It is suitable for use in outdoor kitchens as long as it is well protected from the elements and direct sunlight. The refrigerator comes in three model numbers: BF3310, BF2200, and BF1130.
The refrigerator features glass doors and is built-in for cabinet or similar outdoor kitchen arrangements. It is intended for household and similar applications only.
Important safety instructions include not operating the refrigerator in direct sunlight, as this can lead to increased temperature, excessive energy consumption, and premature component failure, which will not be covered by warranty.
Proper disposal of old appliances and packaging materials is also emphasized to ensure safety.
Product Usage Instructions
-
Before Using For the First Time:
- Allow the refrigerator to stand still and upright for 8 hours before plugging it into power.
- Position the shelf-supports inside the racks on the sides at your required level and place the shelves firmly on the supports.
- Check that the refrigerator is functioning correctly before installing shelves and filling it. The maximum load for a shelf is 40Kg.
-
Cleaning:
-
Unplug the BeefEater Fridge from the power source and remove any items from inside. Temporarily store them in another refrigerator.
-
Wash the inner compartment with warm water and neutral mild detergent. Avoid getting the control panel, cables, or plug wet. Do not use corrosive detergents, wire blasters, or abrasive scourers.
Avoid scraping any part of the fridge with metal or sharp implements. -
Dry all surfaces thoroughly.
-
Clean the condenser every three months using a vacuum hose. The condenser is located behind the lower grill of the cabinet. In exceptionally dusty areas, it is recommended to clean the condenser more often.
-
Use mild soapy water to clean the gasket and seals around the door.
-
Clean the external surfaces of the fridge with warm water and mild detergent or a non-abrasive cleaner.
To ensure safe operation, please readad this instruction manual thoroughly
before e use.
Welcome to your new BeefEEater Fridge
Thank you for purchasing this commermercial style BeefEater Fridge. It has
been designed ed and manufactured for many years of trouble-free service. It
It isis suitable to be used outdoors, as long as it is is wwell protected from
the elements, and any direct sunlight.
Operation is very simple, but please takake a few minutes to read this
booklet. It contains ains safety information and tips to ensure you receive
from your BeeBeefEater Fridge.
Important Safety Instructionsions
This Refrigerator has been designed to be Builted to be Built-in in a cabinet
or similar “Outdoors Kitchen” arrarrangement. This appliance is intended to be
used in housed in household and similar applications only.
Before starting the installation, consid nsideratieration should be given to
how the installation is to be cto be carried out, ensuring
- Adequate space and clearances. nces.
- Preventing exposure to the elements. elements.
- Preventing any exposure to direct sirect sun light.
- Availability of earthed power.
- The mechanical strength of supp supporting structures.
The installation work must be undertakertaken by a qualified and competent
person in confnformity to the rules concerning connection of electric powerc
power and wiring rules.
The manufacturer does not accept any liabilit any liability for any damage or
injury caused by improper installati installation. Before connecting to the
mains supply ensureply ensure that the mains voltage corresponds with theds
with the voltage on the Refrigerator’s rating label.
Make sure the electric plant of your hous your house is correctly earthed.
When installed, the Fridge must be po e posisitioned to ensure no moisture ingress into the applithe appliance or the appliance compartment.
- Before carrying out any kind of maintenand of maintenance or cleaning, disconnect the Fridge from te from the mains supply.
- The appliance must not be operated oed or left out in the weather. Do not expose the RefrigeraRefrigerator to rain or wet conditions.
- This appliance is not intendtended for use by persons (including children) with r ren) with reeduced physical, sensory or mental capabilities, or lack lack of experience and knowledge, unless they hahaveve been given supervision or instruction concerning use g use of the appliance by a person responsible for their safet etyy.
- Children should be supervirvised t sed to ensure that they do not play with the applianccee.
- If the supply cord is damagedaged, it must be replaced by the manufacturer, its servicevice agent or similarly qualified persons in order to avoid aid a hazard.
- There shall be adequate venventilation of the area when the Refrigerator is used, aned, and vents provided must be kept clear, clean and open.pen.
- There is a fire risk if cleanin cleaning is not carried out in accordance with the instru instructio ctions, or if damage occurs to cooling system.
- Always ensure the Refrigerefrigerator is kept at the correct settings for the required op operation of the appliance. Do not use cooking utensiensils to handle things inside, or clean the interior of the fridgridge, as damage to liners may result.
- During use rear of applianliance becomes hot. Care should be taken to avoid touchuchiing elements at rear of the Fridge.
- Children should never be e aallowed to sit or stand on any part of the appliance.
- Use this appliance only for r its intended use.
- This appliance is intended ftended for household use only. It is designed to be used in sheled in sheltered areas only and must not be exposed to the elemements.
NOTE:
THE REFRIGERAEFRIGERATOR MUST NEVER OPERATE IN DIREDIRECT SUNLIGHT! The
refrigeratoror will not operate to specifications if susunlight penetrates the
glass doorsdoors. Prolonged exposure to direct sunlignlightht inside the
fridge will result in incrincreased temperature, excessive energyy
consumption, and even prematurree component failure, and will not be coovered
by warranty.
Please also Note:
Before switching your BeefEater Fridge on for the first time, read the
information in this user manual carefully.
This manual contains important information relating to the assembly, operation
and maintenance of the appliance.
Please keep this booklet in a safe place for future reference. If you ever
sell your BeefEater Fridge, hand this user manual to the new owner.
The manufacture does not accept responsibility for any damages that may arise
due to non-observation of these instructions. The user is liable for any
material damage or bodily injury (product liability) cause by using the
refrigerator carelessly or failing to follow instructions.
- Do not use damaged appliance. If you are in any doubt, consult a suitably qualified technician.
- Connection and installation of your BeefEater Fridge are to be carried out in strict compliance with the instructions in this manual.
- For safety, the appliance must be properly earthed in accordance with specifications
- Do not damage any parts of the appliance which carry refrigerant by piercing, perforating, crushing, twisting or scraping. If the refrigerant comes into contact with the eyes, it may cause serious eye injury.
- Always remember to unplug the appliance before cleaning. Never unplug your appliance by pulling on the power cable. Always grip plug firmly and pull straight out from the socket. Always check that the plug and cable are undamaged.
- All repairs must be carried out by a qualified technician. Inadequate repairs may be dangerous. Never try to repair the refrigerator yourself.
- Should the cover of the interior light or fan fall off or break, switch the refrigerator off immediately and replace the cover.
- Ensure your chosen location has a flat and stable surface. The unit may be leveled by turning either or both of the adjustable feet in the front corners. Check the unit is level using a spirit level.
- Do not obstruct or cover the ventilation aperture.
- Make sure there is a suitable power Outlet (240 volts, 10 amps outlet) with proper grounding to power the refrigerator.
Disposal of Old Appliances
Be sure to make any locks unusable, remove any doors and discard separately.
Warning – chemical hazard: do not allow children to play with the old appliance.
Contact your local authority for disposal procedures.
Before disposing of an old appliance, please make sure it is switched off and
safe. Unplug the appliance and break any locks in order to avoid children
becoming trapped.
Please note: refrigeration system contains gas and refrigerants which require
specialised waste disposal. Some vulnerable materials in a refrigerator can be
recycled .Contact your local waste disposal depot for proper disposal of an
old appliance and contact your local authority or dealer if you have any
questions.
Please ensure the cooling systems and tubes of your refrigerator are not
damaged prior to disposal.
You can contribute to environmental awareness by insisting on an appropriate
non-polluting method of disposal.
Disposal of Packaging
Do not allow children to play with the packaging, and dispose of plastic bags
safely.
The cardboard may be broken or cut into smaller pieces and recycled. Any
wrapping cover is made of polyethylene. The polyethylene pads and padding
contain no fluorochloric hydrocarbons, and as such are most suitable for
adequate recycling.
Before Using For the First Time
Do not position this appliance with its rear panel directly against a wall.
For good circulation and operating efficiency, the ventilation grilles must
never be blocked.
Remove all packaging and place the BeefEater Fridge on a stable, secure flat
surface. Position the
BeefEater Fridge away from heat sources, where the unit is well-ventilated and
protected from moisture, or extremes of heat or cold. The refrigerator may not
function properly if the ambient temperature rises above +40 for prolonged
periods of time.
When installed in a BeefEater Outdoor Kitchen, ensure the vents behind the
fridge are clear, and clean, and not obstructed from the other side, such that
air circulation is enabled.
Do Not Use An Extension Lead. If the mains cable will not reach the nearest
socket, either rearrange your installation layout or ask a qualified
electrician to fit a new socket.
If power is cut off, wait for at least 5 minutes before plugging the unit in
again to avoid damaging the compressor.
Do not place combustible, explosive or volatile articles, corrosive acid or
alkali, or liquid in glass containers into the BeefEater Fridge. Always
exercise caution if adjusting the temperature.
IMPORTANT: allow the refrigerator to stand still and upright for 8 hours before plugging it into the power!
Preparation
Position the Shelf-Supports inside the racks on the sides as illustrated below, at your required level, and then place the shelves firmly on the supports.
Note: check that the refrigerator is functioning correctly before installing shelves and filling it.
The maximum load for a shelf is 40Kg.
Cleaning
-
Unplug your BeefEater Fridge from power source and remove any items from inside. It is best to place these temporarily in another refrigerator.
-
Wash the inner compartment with warm water and neutral mild detergent. DO NOT allow the control panel, cables or plug to get wet.
NEVER use corrosive detergents, wire blasters, or abrasive scourers to clean your BeefEater Fridge.
NEVER use metal or sharp implements to scrape any part of the fridge. -
Dry all surface thoroughly.
-
To ensure trouble-free operation the condenser should be cleaned every three months where appropriate using a vacuum hose. The condenser is located behind lower grill of the cabinet. In exceptionally dusty
It is recommended that areas around the condenser are cleaned more often. -
Use mild soapy water to clean the gasket and seals around the door.
The external surfaces of the fridge can be cleaned with warm water and mild detergent, or with a suitable Stainless-Steel cleaning material.
Electronic Control
The electronic controller is located outside the unit on the bottom, right- hand side front plinth.
It looks like this:
During normal operation the controller display will show the temperature inside the refrigerator.
A small indicator light will illuminate under the ‘Cooling’ symbol to confirm the fridge is in its normal cooling mode, and compressor is running.
Operation of the controller
-
To set the desired temperature of the fridge:
o Press the button once. A ‘beep’ will sound, and the display will start to flash.- Use the buttons to set to the desired temperature.
- Press again to complete the operation, or just leave it for 5 – 10 sec, and the display will revert back to showing internal temperature, while new settings saved.
Note:
The fridge is built to automatically defrost and prevent any ice forming on
the Evaporator.
It will automatically run a ‘Defrost cycle for 20min once every 8 hours.
When in a ‘Defrost’ cvcle. the indicator light will illuminate under the
‘Defrost’ sumbol:
To manually activate ‘Defrost’ cycle:
-
Press the button, and hold it. a ‘beep’ will sound as soon as pressed.
Hold button pressed for 10 – 20 seconds, until a second ‘beep’ can be heard. -
The indicator light will now illuminate under the ‘Defrost’ symbol and the fridge is into a ‘Defrost’ cycle.
-
‘Defrost’ will run for 20min, and then automatically revert to normal operation.
- To manually change back to normal operating mode from the ‘Defrost’ mode:
-
Press the button again, a ‘beep’ will sound.
-
Hold button pressed for 10 – 20 seconds, until a second ‘beep’ is heard.
-
Both indicator lights under the ‘Defrost’ symbol and under the ‘Cooling’ symbol will now flash operation.
while the fridge is gearing up to switch back to normal -
After 5 – 20 minutes, only the indicator light I will illuminate under the ‘Cooling’ symbol to confirm the fridge is back in its normal cooling mode.
Important:
The fridge will go through a normal periodical defrosting cycle, and a manual
defrosting operation is only require in most extreme cases. It is better to
avoid if not necessary.
While in the ‘defrost’ mode, the fridge cooling power is reduced, as the
compressor is notworking. The automatic cycles ensure the defrosting is done
in the most efficient manner, and when required. It is not recommended to
leave the fridge in the manually set defrost mode for prolonged periods of
time.
NOTE: the controller allows you to choose a desired operating temperature
of between -2°c and 8°c.
BeefEater do not recommend to operate the fridge on settings of below 4°c, as
such settings will cause content of the fridge to freeze, and will result in
unnecessary strain on the cooling systems, and undue high energy consumption.
- it is advisable to keep the cover over the controller closed when not being accessed, so no unintended operation or damage will occur.
- in normal operation the controller turns the compressor off at the set temperature, and back on after the temperature had risen by a few degrees.
As such, the reading in the controller is always a couple of degrees above set-point, and that is perfectly OK.
When temperature was reached and the compressor is in its ‘off’ cycle, no indicator light will illuminate in the controller:
Internal Fridge Light
The light inside the fridge can be turned On and Off using the light switch
found on the right-hand side internal wall of the fridge:
Replacing Lamps
Your BeefEater Fridge is using long-life, energy-saving LED light tube. Should
you need to replace this light, please contact your nearest BeefEater
stockiest or service agent for a suitable replacement part.
To change the light tube:
- Unplug the power plug and ensure the light switch is off.
- Remove the screws on both end of the light cover.
- Take off the lamp cover, pull out the wires slightly.
- Gently pull out the connector at the end of the light tube.
- 0Insert the connector into the new lamp, place the lamp cover and fasten it.
Technical Information
Note: your BeefEater Fridge is built to eliminate any fog accumulating on the glass doors, so vision through the doors is never obstructed. This is achieved by heating the outer surface of the door slightly, and as such it is normal for the door to feel slightly warm for the touch.
Woodland Home Products
3-5 Birmingham Av, Chester Hill, NSW,
Australia, 2162
Phone: 1800 356 660
Facsimile: 02 9724 8899
E-mail: mail@beefeaterbbq.com
Website: www.beefeaterbbq.com
USA TollFree:
1866 550 2333
Images in this manual are for illustrative purposes only.
Due to constant improvement, Beeffater advises that changes to the design,
material, specifications and product configuration may occur at any time
without notice.
Warranty
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Should any part fail due to defective workmanship or faulty materials within the specified period from the date of purchase, BeefEater or its distributor will repair or, (at distributors option), replace the defective part free of charge.
Warranty Administration
In Australia, warranty is administered by Woodland Home Products.
To ensure speedy processing of your warranty service claim, ensure that you
record all specific details about your BeefEater Fridge. Keep this information
handy for future reference, and a copy of your purchase receipt.
Not Covered
Storage
BeefEater fridge must not be exposed to the elements. It must never be
positioned in direct sunlight, or subjected to any moisture ingress.
This warranty does not cover the purchaser or any other person for damage,
malfunction or loss due to the following:
- Lack of maintenance, abuse, neglect, misuse, accident or improper installation of this Fridge.
- Scratches, dents, corrosion or discoloring caused by heat, abrasive or chemical cleaners or chipping of porcelain or painted parts.
- Corrosion or damage caused by exposure to the elements, grease fires, insects, weather or hail.
- Cleaning and normal wear and tear. Service calls of this nature are chargeable.
- Rusting of steel parts and accessories.
- Commercial use of the Fridge.
- Unauthorized repairs during the warranty period
- Removal or re-installation costs.
- Cracks and weathering of any parts caused by exposure to the elements or damage by weather, heat, insects, chemicals or foods acids or juices.
Note:
- Fridge must be protected and under cover at all times.
- Any staining to the outer surfaces should be removed by a gentle scrub pad and the surface cleaned with suitable cleaning materials.
Conditions of Warranty
- The BeefEater Fridge is delivered to the BeefEater distributor’s service department or authorized service agent and freight charges both ways are paid by the owner. No liability is accepted for loss or damage during transit
- The Barbecue is operated and maintained in accordance with the instructions supplied.
- Repairs or service must be carried out by an authorized person. Installation must be in line with instructions as set out in this book.
- No alterations or repairs have been carried out without obtaining the distributors prior consent. Such repair or any replacement does not extend the warranty period.
- Proof of purchase together with this warranty card must be provided to verify purchase date and establish the warranty period. Only the original purchaser is covered under this warranty.
- The warranty period is calculated from the date of purchase only.
- Where this warranty is inconsistent with any state laws, the statutory rights of the purchaser shall prevail.
- Parts installed from other manufacturers’ products will void this warranty.
Warranty Term
All parts and workmanship of this BeefEater Fridge are covered for a period of
1 year from date of purchase.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>