DPL500ATMLTER2 Hercules Power Adapter User Guide
- June 13, 2024
- DPL
Table of Contents
Quick Install Guide
No Rules. Just Results.
REV # DPL500ATMLTER2
Equipment Supplied
If any of the above items are missing please contact DPL.
Before You Begin
Activate the Hercules (if not pre activated) a minimum of two-days before installation by logging in to the Hercules Portal at hercules. dplwireless.com or by contacting DPL technical support at 1-800-561-8880 or by email at support@dplwireless.com
Be prepared to provide the following information:
- Company name
- Email address
- Hercules serial number
- Connectivity type (dial up or IP)
- Transaction processor*
- Message format to be used
*If the ATM is new to you, contact your transaction processor to set it up. For IP only ATMs. Message format supplied by transaction processor.
Connecting the Hercules
Step 1 Connect the antennas to the Hercules by screwing the SMA
connectors into the antenna jacks of the Hercules (hand tight).
Secure the magnetic mounts at the base of the antennas to a metallic surface
or near the top of the ATM terminal in a vertical orientation (top of
antenna’s pointing upward).
The MAIN antenna, connected closest to the power jack (pictured above) should
be placed in the most ideal location. The AUX antenna should be placed a
minimum of four inches away or more from the MAIN antenna. Ensure the antennas
are placed away from electronics or other metallic objects that may cause
signal interference.
Step 2 Connect the required communication cable (ethernet or telephone)
from the ATM to the Hercules.
Step 3 Plug the power adapter into the Hercules and then plug it into an
AC outlet. Verify the green Power indicator is lit on the Hercules.
Step 4 Verify the green ATM and SRVC indicators are lit indicating the
Hercules is successfully communicating with DPL’s data centers.
Step 5 Place the Hercules inside the safe of the ATM and lock the safe.
ATM Configuration
Depending on your chosen connectivity type, configure the ATM using the settings below:
IP
ATM
-
Enable DHCP
or -
Static Settings:
• IP Address: 192.168.0.55
• Subnet: 255.255.255.0
• Gateway: 192.168.0.52
Host
- Disable URL
- Host Address (1&2): 192.168.0.52
- Host Port (1&2): 8000
- Disable SSL
- Disable Permanent TCP/IP
Dial Up
ATM
- Modem speed: 1200 baud or 2400 baud
Host
- Host number: 555-0120
RMS Configuration (Optional)
2-Way configuration is available for ATMs that use remote management software (RMS).
Step 1
Configure ATM
Dial Up
- RMS telephone number: 555-0155
- Modem baud rate: 14,400 or less
- Note what your baud rate is and any other protocol settings. The Hercules+ supports v.22bis, v.32 and v.32bis (2400 – 14,400) baud rates for 2-Way.
IP
- RMS Server IP: 192.168.0.53
Note: The above settings are DPL’s standard configuration. If these
settings are not available in your ATM, contact DPL technical support.
Step 2
Contact DPL technical support to assist with RMS server configuration and
software installation.
FCC Statement
Antenna Placement: Place antenna so a minimum of 8 inches is maintained
between it and any person to limit RF exposure to within FCC guidelines. Note:
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with these
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Re-orient or relocate the antenna,
- Increase the separation between the equipment and the receiver,
- Connect the equipment into an outlet or a circuit different from that to which the receiver is connected, and
- Consult DPL or an experienced radio/TV technician for help.
Warning
Changes or modifications not expressly approved by DPL could void the user’s
authority to operate the equipment.
Declaration
This equipment contains a radio module Gemalto ELS61-US or Gemalto ELS31-V.
Refer to product label for FCC / ICAN numbers.
Electronic Devices
Most modern electronic equipment is shielded from radio frequency (RF) signals. However certain electronic equipment may not be shielded against the RF signals from the Hercules (LTE/HSPA) wireless modem. This should be considered before installing in sensitive areas such as Medical Facilities and facilities that ban the use of Digital Cellular Phones.
Trademarks and Copyright
Hercules/Hercules+ is a trademark of DPL. All rights to this publication are reserved. No part of this publication may be copied, reproduced, transmitted or stored in any form or by any means (including electronic, mechanical, photocopying, recording, or otherwise) without prior written permission from DPL.
Disclaimer
While all reasonable care has been taken to ensure that the description,
opinions and text are accurate and workable, DPL does not accept any legal
responsibility or liability to any person, organization or other entity for
any direct loss, consequential loss or damage, however caused, that may be
suffered as a result of the use of this publication or equipment.
Specifications
| Warranty | 5 years parts and labour. Details available from DPL. |
|---|---|
| Dial In Interface | Central Office POTS Line, RJ-11, 2400 baud v.22bis or 1200 |
Baud
Ethernet Port| Supports 10/100T speeds and straight or crossover cables
Interface Port| Custom port for Protetcor / Restart harness which is optional
Protocols Supported| VISA-2, Security Encoding: Triple DES
Network Services| 4G Data over LTE network with ability to fall back to
3G/HSPA (carrier dep.)
Power Supply Output| 12VDC, 2A, Center Positive, 5.5mm x 2.1mm
Power Supply Input| 100-240VAC, 50-60 Hz, 1.0 A Max
Dimensions (h w d)| 3.8 x 12.2 x 14.5 cm (1.5 x 4.8 x 5.7 inches)
Operating Temp| -10 to 45 °C (14 to 113 °F)
Weight| 1.1 kg (2.4 lbs.)
support@dplwireless.com
1-800-561-8880
https://manual-hub.com/
No Rules. Just Results.
Documents / Resources
| dpl
DPL500ATMLTER2 Hercules Power
Adapter
[pdf] User Guide
01, DPL500ATMLTER2 Hercules Power Adapter, Hercules Power Adapter, Power
Adapter, Adapter
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>