AEG IKE95771FB Hob User Manual

IKE95771FB Hob
User Manua l

IKE95771FB Hob

IMPORTANT INFORMATION THAT MAY IMPACT YOUR MANUFACTURER’S WARRANTY
Adherence to the directions for use in this manual is extremely important for health and safety. Failure to strictly adhere to the requirements in this manual may result in personal injury, property damage and affect your ability to make a  claim under the AEG manufacturer’s warranty provided with your product. Products must be used, installed and operated in accordance with this manual. You may not be able to claim on the AEG manufacturer’s warranty in the event that your product fault is due to failure to adhere to this manual.
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. Visit our website for:
Get usage advice, brochures, trouble shooter, service information: www.aeg.com
Register your product for better service: www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance: www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the following data available: Model, PNC, Serial Number.
The information can be found on the rating plate. Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damage that are the result  of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
1.1 Children and vulnerable people safety

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children of less than 8 years of age and persons with very extensive and complex disabilities shall be kept away from the appliance unless continuously supervised.
• Children should be supervised to ensure that they do not play with the appliance.
• Keep all packaging away from children and dispose of it appropriately.
• WARNING: The appliance and its accessible parts become hot during use. Keep children and pets away from the appliance when in use and when cooling down.
• If the appliance has a child safety device, it should be activated.
• Children shall not carry out cleaning and user maintenance of the appliance without supervision.

1.2 General Safety

• This appliance is for cooking purposes only.
• This appliance is designed for single household domestic use in an indoor environment.
• This appliance may be used in, offices, hotel guest rooms, bed & breakfast guest rooms, farm guest houses and other similar accommodation where such use does not exceed (average) domestic usage levels.
• WARNING: The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements.
• WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.
• Never use water to extinguish the cooking fire. Switch off the appliance and cover flames with e.g. a fire blanket or lid.
• WARNING: The appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by a utility.
• CAUTION: The cooking process has to be supervised. A short term cooking process has to be supervised continuously.
• WARNING: Danger of fire: Do not store items on the cooking surfaces.
• Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot.
• Do not use the appliance before installing it in the built-in structure.
• Do not use a steam cleaner to clean the appliance.
• After use, switch off the hob element by its control and do not rely on the pan detector.
• If the glass ceramic surface / glass surface is cracked, switch off the appliance and unplug it from the mains. In case the appliance is connected to the mains directly using junction box, remove the fuse to disconnect the appliance from power supply. In either case contact the Authorised Service Centre.
• If the supply cord is damaged, it must be replaced by the manufacturer, an authorized Service or similarly qualified persons in order to avoid a hazard.
• WARNING: Use only hob guards designed by the manufacturer of the cooking appliance or indicated by the manufacturer of the appliance in the instructions for use as suitable or hob guards incorporated in the appliance. The use of inappropriate guards can cause accidents.

SAFETY INSTRUCTIONS

2.1 Installation
WARNING!
Only a qualified person must install this appliance.
WARNING!
Risk of injury or damage to the appliance.

• Remove all the packaging.

• Do not install or use a damaged appliance.

• Follow the installation instructions supplied with the appliance.

• Keep the minimum distance from other appliances and units.

• Always take care when moving the appliance as it is heavy. Always use safety gloves and enclosed footwear.

• Seal the cut surfaces of the cabinet with a sealant to prevent moisture from causing swelling.

• Protect the bottom of the appliance from steam and moisture.

• Do not install the appliance next to a door or under a window. This prevents hot cookware from falling from the appliance when the door or the window is opened.

• Each appliance has cooling fans on the bottom.

• If the appliance is installed above a drawer:
  – Do not store any small pieces or sheets of paper that could bepulled in, as they can damage the cooling fans or impair the cooling system.
  – Keep a distance of minimum 2 cm between the bottom of the appliance and parts stored in the drawer.

• Remove any separator panels installed in the cabinet below the appliance.

2.2 Electrical Connection
WARNING!
Risk of fire and electric shock.

• All electrical connections should be made by a qualified electrician.
• The appliance must be earthed.
• Before carrying out any operation make sure that the appliance is disconnected from the power supply.
• Make sure that the parameters on the rating plate are compatible with the electrical ratings of the mains power supply.
• Make sure the appliance is installed correctly. Loose and incorrect electricity mains cable or plug (if applicable) can make the terminal become too hot.
• Use the correct electricity mains cable.
• Do not let the electricity mains cable tangle.
• Make sure that a shock protection is installed.
• Use the strain relief clamp on the cable.
• Make sure the mains cable or plug (if applicable) does not touch the hot appliance or hot cookware, when you connect the appliance to a socket.
• Do not use multi-plug adapters and extension cables.
•  Make sure not to cause damage to the mains plug (if applicable) or to the mains cable. Contact our Authorised Service Centre or an electrician to change a damaged mains cable.
• The shock protection of live and insulated parts must be fastened in such a way that it cannot be removed without tools.
• Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation.
• If the mains socket is loose, do not connect the mains plug.
• Do not pull the mains cable to disconnect the appliance. Always pull  the mains plug.
• Use only correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the holder), earth leakage trips and contactors.
• The electrical installation must have an isolation device which lets you disconnect the appliance from the mains at all poles. The isolation device must have a contact opening width of minimum 3 mm.

2.3 Use
WARNING!
Risk of injury, burns and  electric shock.

• Do not change the specification of this appliance.
• Remove all the packaging, labelling and protective film (if applicable) before first use.
• Make sure that the ventilation openings are not blocked.
• Do not let the appliance stay unattended during operation.
• Set the cooking zone to “off” after each use.
• Do not put cutlery or saucepan lids on the cooking zones. They can become hot.
• Do not operate the appliance with wet hands or when it has contact with water.
• Do not use the appliance as a work surface or as a storage surface.
• f the surface of the appliance is cracked, disconnect immediately the appliance from the power supply. This to prevent an electrical shock.
• Users with a pacemaker must keep a distance of minimum 30 cm from the induction cooking zones when the appliance is in operation.
• When you place food into hot oil, it may splash.

WARNING!
Risk of fire and explosion

• Fats and oil when heated can release flammable vapours. Keep flames or heated objects away from fats and oils when you cook with them.
• The vapours that very hot oil releases can cause spontaneous combustion.
• Used oil, that can contain food remnants, can cause fire at a lower temperature than oil used for the first time.
• Do not put flammable products or items that are wet with flammable products in, near or on the appliance.

WARNING!
Risk of damage to the appliance.

• Do not keep hot cookware on the control panel.
•  Do not put a hot pan cover on the glass surface of the hob.
• Do not let cookware boil dry.
• Be careful not to let objects or cookware fall on the appliance. The surface can be damaged.
• Do not activate the cooking zones with empty cookware or without cookware.
• Do not put aluminum foil on the appliance.
• Cookware made of cast iron or with a damaged bottom can cause scratches  on the glass / glass ceramic. Always lift these objects up when you have to move them on the cooking surface.

2.4 Care and cleaning

• Clean the appliance regularly to prevent the deterioration of the surface material.
• Switch off the appliance and let it cool down before cleaning.
• Do not use water spray and steam to clean the appliance.
• Clean the appliance with a moist soft cloth. Use only neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects.

2.5 Service

• To repair the appliance contact the Authorised Service Centre. Use original spare parts only.
• Concerning the lamp(s) inside this product and spare part lamps sold

INSTALLATION

WARNING!
Refer to Safety chapters.
3.1 Before the installation
Before you install the hob, write down the information below from the rating plate. The rating plate is on the bottom of the hob.
Serial number ………………………
3.2 Built-in hobs
Only use the built-in hobs after you assemble the hob into correct built-in units and work surfaces that align to the standards.
3.3 Connection cable

• The hob is supplied with a connection cable.
• To replace the damaged mains cable, use the cable type: H05V2V2-F which withstands a temperature of 90 °C or higher. Contact an Authorised Service Centre. The connection cable may separately: These lamps are intended to withstand extreme physical conditions in household appliances, such as temperature, vibration, humidity, or are intended to signal information about the operational status of the appliance. They are not intended to be used in other applications and are not suitable for household room illumination.

2.6 Disposal
WARNING!
Risk of injury or suffocation.

• Contact your local authority for information on how to dispose of the appliance.
• Disconnect the appliance from the mains supply.
• Cut off the mains electrical cable close to the appliance and dispose of it. only be replaced by a qualified electrician.

3.4 Assembly
If you install the hob under a hood, please see the installation instructions of the hood for the minimum distance between the appliances.If the appliance is installed above a drawer, the hob ventilation can warm up the items stored in the drawer during the cooking process.Find the video tutorial “How to install your AEG Induction Hob – Worktop installation” by typing out the full name indicated in the graphic below.
www.youtube.com/electrolux
www.youtube.com/aeg
How to install your AEG Induction Hob – Worktop installation

PRODUCT DESCRIPTION

4.1 Cooking surface layout

1. Induction cooking zone
2. Control panel
3. Flexible induction cooking area consisting of four sections

4.2 Control panel layout

| Sensor field| Function| Description
---|---|---|---
1| | On / Off| To activate and deactivate the appliance.
2| | Timer| To set the function.
3| | –| To increase or decrease the time.
4| –| Timer display| To show the time in minutes.
5| | Power Slide| To activate and deactivate the function.
6| | FlexiBridge (Flexible Bridge)| To switch between three modes of the function.
7| | Pause| To activate and deactivate the function.
8| | Lock / Child Safety Device| To lock / unlock the control panel.
9| | Bridge| To activate and deactivate the function.
10| | Hob²Hood| To activate and deactivate the manual mode of the function.
11| | Power Boost| To activate the function.
12| –| Control bar| To set a heat setting.

4.3 Display indicators

warm / residual heat.

DAILY USE

WARNING!
Refer to Safety chapters.

5.1 Activating and deactivating
Press and hold to activate or deactivate the hob.
5.2 Pot detection
This feature indicates the presence of cookware on the hob and deactivates the cooking zones if no cookware is detected during a cooking session.
If you put cookware on a cooking zone before you select a heat setting, the indicator above 0 on the control bar appears.
If you remove cookware from an activated cooking zone and set it aside temporarily, the indicators above the corresponding control bar will start blinking. If you do not place the cookware back on the activated cooking zone within 120  seconds, the cooking zone will automatically deactivate.
To resume cooking, make sure to put the cookware back on the cooking zones within the indicated timeout.

5.3 Using the cooking zones
Place the cookware in the centre of the selected zone. Induction cooking zones adapt to the dimension of the bottom of the cookware automatically.
You can cook with large cookware placed on two cooking zones at the same time. The cookware must cover the centres of both zones but not go beyond the area marking. If the cookware is located between the two centres, Bridge function will not be activated. 

5.4 Heat setting

1. Press the desired heat setting on the control bar.
   The indicators above the control bar appear up to the selected heat setting level.

2. To deactivate a cooking zone, press 0.

5.5 Power Boost
This function makes more power available to the induction cooking zones.
The function can be activated for the induction cooking zone only for a limited period of time. After this time the induction cooking zone automatically sets back to the highest heat setting.

**** Refer to “Technical data” chapter.
To activate the function for a cooking zone: touch.
To deactivate the function: change the heat setting.

5.6 OptiHeat Control (3 step Residual heat indicator)

WARNING!
/ / As long as the indicator is on, there is a risk of burns from residual heat.
The induction cooking zones produce the heat necessary for the cooking process directly in the bottom of the cookware.
The glass ceramic is heated by the heat of the cookware.
The indicators appear when a cooking zone is hot. They show the level of the residual heat for the cooking zones you are currently using:
– continue cooking,
– keep warm,
– residual heat.
The indicator may also appear:

• for the neighbouring cooking zones even if you are not using them,
• when hot cookware is placed on cold cooking zone,
• when the hob is deactivated but the cooking zone is still hot.

The indicator disappears when the cooking zone has cooled down.

5.7 Timer
Count Down Timer
Use this function to specify how long a cooking zone should operate during a single cooking session.

Set the heat setting for the selected cooking zone and then set the function.
****You cannot activate the function while the Hob²Hood function is running.

1. Press . 00 appears on the timer display.
2. Press or to set the time (00-99 minutes).
3. Press to start the timer or wait 3 seconds. The timer begins to count down.

To change the time: select the cooking zone with and press or .
To deactivate the function: select the cooking zone with and press . The remaining time counts back to 00.
The timer finishes counting down, a signal sounds and 00 blinks. The cooking zone deactivates. Press any symbol to stop the signal and blinking.

Minute Minder
You can use this function when the hob is activated but the cooking zones do not operate. The heat setting shows 00.
****You cannot activate the function while the Hob²Hood function is running.

1. Press .
2. Press or to set the time.
   The timer finishes counting down, a signal sounds and 00 blinks. Press any symbol to stop the signal and blinking.
   To deactivate the function: press and . The remaining time counts back to 00.

5.8 Power management
If multiple zones are active and the consumed power exceeds the limitation of the power supply, this function divides the available power between all cooking zones (connected to the same phase).
The hob controls heat settings to protect the fuses of the house installation.

• If the hob reaches the limit of maximum available power (refer to the rating plate), the power of the cooking zones will be automatically reduced.
• The heat setting of the cooking zone selected first is always prioritised. The remaining power will be divided between the previously activated cooking zones according to the order of selection.
• For cooking zones that have a reduced power, the control bar blinks and shows the maximum possible heat settings.
• Wait until the display stops flashing or reduce the heat setting of the cooking zone selected last. The cooking zones will continue operating with the reduced heat setting. Change the heat settings of the cooking zones manually, if  necessary.

5.9 Menu structure
The table shows the basic menu structure.
User settings

ADDITIONAL FUNCTIONS

6.1 Automatic Switch Off
The function deactivates the hob automatically if:

• all of the cooking zones are deactivated,
• you do not set any heat setting or fan speed setting after the activation of the hob,
• you spill something or put something on the control panel for more than 10 seconds (a pan, a cloth, etc.). A signal sounds and the hob deactivates.
  Remove the object or clean the control panel.

To enter user settings: press and hold for 3 seconds. Then, press and hold. The settings appear on the timer of the left cooking zones.
Navigating the menu: the menu consists of the setting symbol and a value. The symbol appears on the rear timer and the value appears on the front timer. To navigate between the settings press on the front timer. To change the setting value press or on the front timer.

OffSound Control
You can activate / deactivate the sounds in the Menu > User settings.
Refer to “Menu structure”.
When the sounds are off you can still hear the sound when:

• you touch,
• the timer comes down,
• you press an inactive symbol.
• the appliance gets too hot (e.g. when a saucepan boils dry). Let the cooking zone cool down before you use the hob again.
• you do not deactivate a cooking zone or change the heat setting. After some time, the hob deactivates.
  The relation between the heat setting and the time after which the appliance deactivates:

6.2 Pause
This function sets all cooking zones that operate to the lowest heat setting.
When the function operates, and can be used. All other symbols on the control panels are locked.
****The function does not stop the timer functions.

1. To activate the function: press.
   The heat setting is lowered to 1.

2. To deactivate the function: press.
   The previous heat setting comes on.

6.3 Lock
You can lock the control panel while the hob operates. It prevents an accidental change of the heat setting.
Set the heat setting first.
To activate the function: press .
To deactivate the function: press again.
The function deactivates as you deactivate the hob.
6.4 Child Safety Device
****This function prevents an accidental operation of the hob.
To activate the function: press . Do not set any heat setting. Press and hold for 3 seconds, until the indicator above the symbol appears. Deactivate the hob with.

This function connects two right side cooking zones and they operate as one.
First set the heat setting for one of the right side cooking zones.
To activate the function: touch . To set or change the heat setting touch one of the control sensors.
To deactivate the function: touch .
The cooking zones operate independently.

6.6 Flexible induction cooking area
WARNING!
Refer to Safety chapters.
FlexiBridge function
The flexible induction cooking area consists of four sections. The sections can be combined into two cooking zones with different size, or into one large cooking area. You choose the combination of the sections by choosing the mode applicable to the size of the cookware you want to use. There are three modes: Standard, Big Bridge, and Max Bridge.
To set the heat setting use the two control bars on the left side.
Switching between the modes To switch between the modes press .
The heat setting levels will be kept.

Diameter and position of the cookware
Choose the mode applicable to the size and the shape of the cookware. The cookware should cover the selected area as much as possible.
Place the cookware with the bottom diameter smaller than 160 mm centrally on a single section. You can use a roaster pan for the Big Bridge and the Max Bridge modes.

Place the cookware with the bottom diameter larger than 160 mm centrally between two sections.

FlexiBridge Standard mode
This mode is activated by default when you activate the function. It connects the sections into two separate cooking areas. You can set the heat setting for each area separately. Use the two control bars on the left side.

Correct cookware position:

Incorrect cookware position:

FlexiBridge Big Bridge mode
To activate the mode press until you see the correct mode indicator . This mode connects the three rear sections into one cooking area. The front section is not connected and operates as a separate cooking zone. You can set  the heat setting for each area separately.
Use the two control bars on the left side.

Correct cookware position:
Make sure to place the cookware on the three connected sections. If you use cookware smaller than two sections the control bar blinks and after 2 minutes the zone deactivates.

Incorrect cookware position:

FlexiBridge Max Bridge mode
To activate the mode press until you see the correct mode indicator . This mode connects all sections into one cooking area. To set the heat setting use any of the two control bars on the left side.

Correct cookware position:
Make sure to place the cookware on the four connected sections. If you use cookware smaller than three sections the control bar blinks and after 2 minutes the zone switches off.

Incorrect cookware position:

PowerSlide
This function allows you to adjust the temperature by moving the cookware to a different position on the induction cooking area.

• The function divides the induction cooking area into three areas with different heat settings. The hob detects the position of the cookware and adjusts the heat setting corresponding with the position.
• You can place the cookware in the front, middle or rear position. If you place the cookware in the front you get the highest heat setting. To decrease it, move the cookware to middle or rear position.
• When you activate the function for the first time you will get the following default heat settings: 9 for the front position, 6 for the middle position and 3 for the rear position.
• You can change the heat settings for each position separately. The hob will remember your heat settings next time you activate the function.
• The heat setting display of the left front control bar shows the heat setting for this function. To change the heat setting use the left front control bar only. The left rear control bar is deactivated while the function operates.
  **** Use only one pot with a minimum bottom diameter of  160 mm when you operate the function.

1. Place the correct cookware on the left front side of the cooking area.

2. Press and hold to activate the hob.
   A signal sounds and indicators above and appear.

3. Press to activate the function.
   A signal sounds and an indicator above the symbol appears.

4. Move the cookware back and forth on the cooking area as needed.
   The heat setting level on the control bar adjusts automatically.

5. To change the default heat setting levels, move the cookware to the area you want to adjust first.

6. Press any of the available heat setting levels on the left front control bar.
   The updated heat setting levels will be remembered for the next time you use the function.

7. Repeat the procedure for the remaining cooking areas, if needed.

8. To deactivate the function, press .
   You can also press 0 on the left front control bar.

A signal sounds and the indicator above the symbol disappears. The heat setting level changes to 0.
You can set a timer while Power Slide operates. In this case the timer does not deactivate the cooking zones when the set time runs out. The timer affects all three cooking areas activated by the function at the same time.

6.7 Hob²Hood
It is an advanced automatic function which connects the hob to a special hood. Both the hob and the hood have an infrared signal communicator. Speed of the fan is defined automatically on basis of mode setting and temperature of
the hottest cookware on the hob. You can also operate the fan from the hob manually.

For most of the hoods the remote system is originally deactivated.
Activate it before you use the function. For more information refer to hood user manual.

Operating the function automatically
To operate the function automatically set the automatic mode to H1 – H6. The hob is originally set to H5. The hood reacts whenever you operate the hob. The hob recognizes temperature of the cookware automatically and adjusts the speed of the fan.

Automatic modes

| Automatic light| Boiling1| Frying2)
---|---|---|---
Mode HO| Off| Off| Off
Mode H1| On| Off| Off
Mode H2 3)| On| Fan speed 1| Fan speed 1
Mode H3| On| Off| Fan speed 1
Mode H4| On| Fan speed 1| Fan speed 1
Mode H5| On| Fan speed 1| Fan speed 2
Mode H6| On| Fan speed 2| Fan speed 3

1. The hob detects the boiling process and activates fan speed in accordance with automatic mode.
2. The hob detects the frying process and activates fan speed in accordance with automatic mode.
3. This mode activates the fan and the light and does not rely on the temperature.

Changing the automatic mode

1. Deactivate the hob.
2. Press for 3 seconds. The display comes on and goes off.
3. Press for 3 seconds.
4. Press a few times until H comes on.
5. Press of the timer to select an automatic mode.

To operate the hood directly on the hood panel deactivate the automatic mode of the function.
When you finish cooking and deactivate the hob, the hood fan may still operate for a certain period of time. After that time the system deactivates the fan automatically and prevents you from accidental activation of the fan for the next 30 seconds.

Operating the fan speed manually
You can also operate the function manually. To do that press when the hob is active. This deactivates automatic operation of the function and allows you to change the fan speed manually. When you press you raise the fan speed by one. When you reach an intensive level and press again you will set fan speed to 0 which deactivates the hood fan. To start the fan again with fan speed 1 press .

To activate automatic operation of the function, deactivate the hob and activate it again.
Activating the light
You can set the hob to activate the light automatically whenever you activate the hob. To do so set the automatic mode to H1 – H6.
The light on the hood deactivates 2 minutes after deactivating the hob.

HINTS AND TIPS

WARNING!
Refer to Safety chapters.
7.1 Cookware
For induction cooking zones a strong electro-magnetic field creates the heat in the cookware very quickly.
Use the induction cooking zones with suitable cookware.

• The bottom of the cookware must be as thick and flat as possible.
• Ensure pan bases are clean and dry before placing on the hob surface.
• In order to avoid scratches, do not slide or rub the pot across the ceramic glass.

Cookware material

• correct: cast iron, steel, enamelled steel, stainless steel, multi-layer bottom (with a correct marking from a manufacturer).

• not correct: aluminium, copper, brass, glass, ceramic, porcelain.
  Cookware is suitable for an induction hob if:

• water boils very quickly on a zone set to the highest heat setting.

• a magnet pulls on to the bottom of the cookware.

Cookware dimensions

• Induction cooking zones adapt to the dimension of the bottom of the cookware automatically.
• The cooking zone efficiency is related to the diameter of the cookware. The cookware with a diameter smaller than the minimum receives only a part of the power generated by the cooking zone.
• For both safety reasons and optimal cooking results, do not use cookware larger than indicated in “Cooking zones specification”. Avoid keeping cookware close to the control panel during the cooking session. This might impact the  functioning of the control panel or accidentally activate hob functions.
  Refer to “Technical data”.

7.2 The noises during operation
If you can hear:

• crack noise: cookware is made of different materials (a sandwich construction).
• whistle sound: you use a cooking zone with a high power level and the cookware is made of different materials (a sandwich construction).
• humming: you use a high power level.
• clicking: electric switching occurs.
• hissing, buzzing: the fan operates.
  The noises are normal and do not indicate any malfunction.

7.3 Öko Timer (Eco Timer)
To save energy, the heater of the cooking zone deactivates before the count down timer sounds. The difference in the operation time depends on the heat setting level and the length of the cooking operation.
7.4 Examples of cooking applications
The correlation between the heat setting of a zone and its consumption of power is not linear. When you increase the heat setting, it is not proportional to the increase of the consumption of power. It means that a cooking zone with the  medium heat setting uses less than a half of its power.
****The data in the table is for guidance only.

time to time.
2| Solidify: fluffy omelet’s, baked eggs.| 10 – 40| Cook with a lid on.
2 – 3| Simmer rice and milk based dishes, heat up ready-cooked meals.| 25 – 50| Add at least twice as much liquid as rice, mix milk dishes halfway through the procedure.
3 – 4| Stew vegetables, fish, meat.| 20 – 45| Add a few tablespoons of water. Check the water amount during the process.
4 – 5| Steam potatoes and other vegetables.| 20 – 60| Cover the bottom of the pot with 1-2 cm of water. Check the water level during the process. Keep the lid on the pot.
4 – 5| Cook larger quantities of food, stews and soups.| 60 – 150| Up to 3 I of liquid plus ingredients.
6 – 7| Gentle fry: escalope, veal cordon bleu, cutlets, rissoles, sausages, liver, roux, eggs, pancakes, doughnuts.| as necessary| Turn over when needed.
7 – 8| Heavy fry, hash browns, loin steaks, steaks.| 5 – 15| Turn over when needed.
9| Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.
P| Boil large quantities of water. Power Boost is activated.

7.5 Hints and Tips for Hob²Hood
When you operate the hob with the function:

• Protect the hood panel from direct sunlight.
• Do not spot halogen light on the hood panel.
• Do not cover the hob control panel.
• Do not interrupt the signal between the hob and the hood (e.g. with the hand, a cookware handle or a tall pot). See the picture.

The hood pictured below is for illustration purpose only.

Other remotely controlled appliances may block the signal. Do not use any such appliances near to the hob while Hob²Hood is on.
Cooker hoods with the Hob²Hood function
To find the full range of cooker hoods which work with this function refer to our consumer website. The AEG cooker hoods that work with this function must have the symbol .

CARE AND CLEANING

WARNING!
Refer to Safety chapters.
8.1 General information

• Clean the hob after each use.
• Always use cookware with a clean base.
• Scratches or dark stains on the surface have no effect on how the hob operates.
• Use a special cleaner suitable for the surface of the hob.
• Use a special scraper for the glass.
  ****The printing on the flexible induction cooking area may become dirty or change its colour from sliding the cookware. You can clean the area in a standard way.

TROUBLESHOOTING

WARNING!
Refer to Safety chapters.
Other remotely controlled appliances may block the signal. Do not use any such appliances near to the hob while Hob²Hood is on.
Cooker hoods with the Hob²Hood function
To find the full range of cooker hoods which work with this function refer to our consumer website. The AEG cooker hoods that work with this function must have the symbol.

CARE AND CLEANING

WARNING!
Refer to Safety chapters.
8.1 General information

• Clean the hob after each use.
• Always use cookware with a clean base.
• Scratches or dark stains on the surface have no effect on how the hob operates.
• Use a special cleaner suitable for the surface of the hob.
• Use a special scraper for the glass.
  The printing on the flexible induction cooking area may become dirty or change its colour from sliding the cookware. You can clean the area in a standard way.

8.2 Cleaning the hob

• Remove immediately: melted plastic, plastic foil, salt, sugar and food with sugar, otherwise, the dirt can cause damage to the hob. Take care to avoid burns. Use a special hob scraper on the glass surface at an acute angle and move  the blade on the surface.
• Remove when the hob is sufficiently cool: limescale rings, water rings, fat stains, shiny metallic discoloration. Clean the hob with a moist cloth and a non-abrasive detergent. After cleaning, wipe the hob dry with a soft cloth.
• Remove shiny metallic discoloration: use a solution of water with vinegar and clean the glass surface with a cloth.

9.1 What to do if…

You cannot activate or oper‐
ate the hob.| The hob is not connected to
an electrical supply or it is
connected incorrectly.| Check if the hob is correctly connected to the electrical supply. Refer to the connection diagram.
| The fuse is blown.| Make sure that the fuse is the cause of the malfunction.
If the fuse is blown again and again, contact a  qualified electrician.
| Pause operates.| Refer to “Daily use”.
Hob²Hood does not work.| You covered the control pan‐
el.| Remove the object from the control panel.
| You use a very tall pot which
blocks the signal.| Use a smaller pot, change the cooking zone or  operate the hood manually.
There is no sound when you
touch the panel sensor
fields.| The sounds are deactivated.| Activate the sounds. Refer to “Daily use”.
The flexible induction cook‐
ing area does not heat up
the cookware.| The cookware is in a wrong position on  the flexible induction cooking area.| Place the cookware in the correct position on  the flexible induction cooking area.
The position of the cookware depends on the  activated function or function mode.
Refer to “Flexible induction cooking area”.
| The diameter of the bottom of the  cookware is incorrect for the activated function or function mode.| Use cookware with a diameter applicable to the activated function or function mode. Use  cookware with a diameter smaller than 160 mm  on a single section of the flexible induction  cooking area. Refer to “Flexible induction  cooking area”.
| FlexiBridge operates. One or more  sections of the function mode which operates are not covered by the cook‐ ware.| Place the cookware on the correct number of  sections of the function mode which operates or  change the function mode. Refer to “Flexible induction cooking area”.
| PowerSlide operates. Two pots are  placed on the flexible induction  cooking area.| Use only one pot. Refer to “Flexible induction  cooking area”.

9.2 If you cannot find a solution…
If you cannot find a solution to the problem yourself, contact your dealer or an Authorised Service Centre. Give the data from the rating plate. Make sure, you operated the hob correctly. If not the servicing by a service technician or
dealer will not be free of charge, also during the warranty period. The information about guarantee period and Authorised Service Centres are in the guarantee booklet.

TECHNICAL DATA

10.1 Rating plate

Model IKE95771FB
Typ 62 E5A 07 AA
Induction 7.35 kW
Ser.Nr. ……………..
AEG| PNC 949 597 976 00
220 – 240 V, 50 Hz
Made in: Germany
7.35 kW
---|---

10.2 Cooking zones specification

Cooking zone| Nominal power (maximum heat setting) [W]| PowerBoost [W]| PowerBoost maximum duration [min]| Cookware diameter [mm]
---|---|---|---|---
Middle rear| 1800 / 3500| 2800 / 3700| 10 / 10| 145 – 245 / 245 -280
Right front| 2300| 3200| 10| 125 – 210
Right rear| 2300| 3200| 10| 125 – 210
Flexible induc- tion cooking area| 2300| 3200| 10| minimum 105

The power of the cooking zones can be different in some small range from the data in the table. It changes with the material and dimensions of the cookware.
For optimal cooking results use cookware no larger than the diameter in the table.

ENERGY EFFICIENCY

11.1 Energy saving
You can save energy during everyday cooking if you follow the hints below.

• When you heat up water, use only the amount you need.
• If it is possible, always put the lids on the cookware.
• Put the cookware directly in the centre of the cooking zone.
• Use the residual heat to keep the food warm or to melt it.

WARRANTY – AUSTRALIA AND NEW ZEALAND

FOR SALES IN AUSTRALIA AND NEW ZEALAND
ALL AEG BRANDED APPLIANCES
This document sets out the terms and conditions of the product warranties for AEG Appliances. It is an important document. Please keep it with your proof of purchase documents in a safe place for future reference should there be a manufacturing defect in your Appliance. This warranty is in addition to other rights you may have under the Australian Consumer Law.

1. In this warranty:
   a) ‘ACL’ or ‘Australian Consumer Law’ means Schedule 2 to the Competition and Consumer Act 2010;
   b) ‘Appliance’ means any Electrolux product purchased by you and accompanied by this document;
   c) ‘ASC’ means Electrolux’s authorised serviced centres;
   d) ‘AEG’ is the brand controlled by Electrolux Home Products Pty Ltd of 163 O’Riordan Street, Mascot NSW 2020, ABN 51 004 762 341 in respect of Appliances purchased in Australia and Electrolux (NZ) Limited (collectively “Electrolux”) of 3-5 Niall Burgess Road, Mount Wellington, in respect of Appliances purchased in New Zealand;
   e) ‘Warranty Period’ means the period specified in clause 3 of this warranty;
   f) ‘you’ means the purchaser of the Appliance not having purchased the Appliance for re-sale, and ‘your’ has a corresponding meaning.

2. Application: This warranty only applies to new Appliances, purchased and used in Australia or New Zealand and is in addition to (and does not exclude, restrict, or modify in any way) other rights and remedies under a law to which  the Appliances or services relate, including any non-excludable statutory guarantees in Australia and New Zealand.

3. Warranty Period: Subject to these terms and conditions, this warranty continues for in Australia for a period of 60 months and in New Zealand for a period of 60 months, following the date of original purchase of the Appliance.

4. Repair or replace warranty: During the Warranty Period, Electrolux or its ASC will, at no extra charge if your Appliance is readily accessible for service, without special equipment and subject to these terms and conditions, repair or  replace any parts which it considers to be defective. Electrolux may, in its absolute discretion, choose whether the remedy offered for a valid warranty claim is repair or replacement. Electrolux or its ASC may use refurbished parts to  repair your Appliance. You agree that any replaced Appliances or parts become the property of Electrolux.

5.  Travel and transportation costs: Subject to clause 7, Electrolux will bear the reasonable cost of transportation, travel and delivery of the Appliance to and from Electrolux or its ASC. Travel and transportation will be arranged by  Electrolux as part of any valid warranty claim.

6. Proof of purchase is required before you can make a claim under this warranty.

7. Exclusions: You may not make a claim under this warranty unless the defect claimed is due to faulty or defective parts or workmanship. This warranty does not cover:
   a) light globes, batteries, filters or similar perishable parts;
   b) parts and Appliances not supplied by Electrolux;
   c) cosmetic damage which does not affect the operation of the Appliance;
   d) damage to the Appliance caused by:
   – negligence or accident;
   – misuse or abuse, including failure to properly maintain or service;
   – improper, negligent or faulty servicing or repair works done by anyone other than an Electrolux authorised repairer or ASC;
   – normal wear and tear;
   – power surges, electrical storm damage or incorrect power supply;
   – incomplete or improper installation;
   – incorrect, improper or inappropriate operation;
   – insect or vermin infestation;
   – failure to comply with any additional instructions supplied with the Appliance; In addition, Electrolux is not liable under this warranty if:
   – the Appliance has been, or Electrolux reasonably believes that the Appliance has been, used for purposes other than those for which the Appliance was intended, including where the Appliance has been used for any nondomestic purpose;
   – the Appliance is modified without authority from Electrolux in writing;
   – the Appliance’s serial number or warranty seal has been removed or defaced.

8. How to claim under this warranty:
   To enquire about claiming under this warranty, please follow these steps:
   a. carefully check the operating instructions, user manual and the terms of this warranty;
   b. have the model and serial number of the Appliance available;
   c. have the proof of purchase (e.g. an invoice) available;
   d. telephone the numbers shown below.

9. Australia: For Appliances and services provided by Electrolux in Australia: Electrolux goods come with guarantees that cannot be excluded under the Australian Consumer Law.
   You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the Appliance repaired or replaced if the Appliance fails to be of acceptable quality and the failure does not amount to a major failure.
   ‘Acceptable quality’ and ‘major failure’ have the same meaning as referred to in the ACL.

10. New Zealand: For Appliances and services provided by Electrolux in New Zealand, the Appliances come with a guarantee by Electrolux pursuant to the provisions of the Consumer Guarantees Act, the Sale of Goods Act and the Fair  Trading Act. Where the Appliance was purchased in New Zealand for commercial purposes the Consumer Guarantee Act does not apply.

11. Confidentiality: You accept that if you make a warranty claim, Electrolux and its agents including ASC may exchange information in relation to you to enable Electrolux to meet its obligations under this warranty.

Important Notice
Before calling for service, please ensure that the steps listed in clause 8 above have been followed.

FOR SERVICE
or to find the address of your nearest authorised service centre in Australia PLEASE CALL 1300 363 664
OR EMAIL
customercare@aegaustralia.com.au
For the cost of a local call (Australia only)

FOR SPARE PARTS
or to find the address of your nearest spare parts centre in Australia
PLEASE CALL 13 13 50
OR EMAIL
customercare@aegaustralia.com.au
For the cost of a local call (Australia only)

SERVICE NEW ZEALAND
aegnewzealand.co.nz

FOR SERVICE
or to find the address of your nearest authorised service centre in New Zealand
PLEASE CALL 0800 234 234
OR EMAIL
customercare@electrolux.co.nz
(New Zealand only)

FOR SPARE PARTS
or to find the address of your nearest spare parts centre in New Zealand
PLEASE CALL 0800 10 66 20
OR EMAIL
customercare@electrolux.co.nz
(New Zealand only)

ENVIRONMENTAL CONCERNS

Recycle materials with the symbol.
Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of appliances marked with the symbol with the household  waste. Return the product to your local recycling facility or contact your municipal office.

www.aeg.com/au 867378347-A-332022

References

• AEG | Premium Home & Kitchen Appliances
• AEG New Zealand | Premium Home & Kitchen Appliances
• Welcome to AEG
• AEG - aeg.com
• Welcome to AEG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>