ENDON 96598 Brodey Table Light Instructions
- June 13, 2024
- ENDON
Table of Contents
ENDON 96598 Brodey Table Light
Product Information
- Product Name: Table Light
- Product Type: Class II, Double Insulated Lamp
- Power Supply: 220-240V~ 50Hz
- Suitability: Indoor use only (not suitable for bathroom location)
- Age Restriction: Not suitable for persons under 14 years of age
- Fuse Requirement: 3 amp fuse in the mains plug
- Manufacturer: UK Manufacturer – BH17 7BY, EU Manufacturer -Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
Product Usage Instructions
- Read the safety warnings and installation instructions thoroughly before using the product.
- Consult a qualified electrician if you have any doubts about installing or using the product.
- Ensure the product is only connected to a suitable 220-240V~ 50Hz power supply.
- Place the lamp on a stable and flat surface before use.
- Assemble the lamp fully before plugging it in or using it. Disconnect from the mains power during assembly or maintenance.
- Do not cover the lamp with any material as it may pose a safety hazard.
- Avoid placing any objects or hanging anything on the lamp.
- Ensure the lamp is protected by a 3 amp fuse in the mains plug.
- Use bulbs with wattage specified on the label. Do not use bulbs with higher wattage as it may damage the fitting.
- For bulb replacement, switch off the product and allow it to cool down before replacing the bulb. Use a dry cloth for cleaning and avoid liquid or abrasive cleaners.
- If the external flexible cable or cord is damaged, it should only be replaced by a qualified electrician.
- Dispose of waste electrical products through appropriate recycling facilities. Check with your Local Authority or local store for recycling advice.
- If the bulb does not light after installation, follow these troubleshooting steps:
- Plug in and operate the foot switch to turn on the lamp.
- Check the bulb.
- Check the 3 amp fuse in the plug and the relevant fuse in your fuse box.
- If in doubt, consult a qualified electrician.
- To use the product in Europe, the 3-pin adaptor can be removed by loosening the central screw and removing the adaptor to reveal the 2-pin Europe plug (BS 5733).
Safety Warnings
These instructions are for your safety. Please read through them thoroughly
before use and retain them for future reference. If you are in any doubt about
installing this product, consult a qualified electrician.
This product is only suitable for connection to a 220-240V~ 50Hz supply. It is
for indoor use only, and not suitable for a bathroom location. This fitting is
a Class II, Double Insulated product and does not require an Earth. Live or
Neutral must not be connected to Earth. Do not attempt to plug in or use this
product until it has been fully assembled. Disconnect from mains during
assembly or maintenance. this product must be used on a stable, flat surface.
Under no circumstances must this lamp be covered with any material as this
could pose a safety hazard.
This product is not suitable for persons under 14 years of age. This product may contain delicate parts – be careful during handling and maintenance to avoid breakage. The lamp must be protected by a 3 amp fuse in the mains plug. Never fit bulbs of a higher wattage than those specified on the label as these may damage the fitting. Never put anything on the product or hang anything on any part of this product. If the external flexible cable or cord of this luminaire is damaged, it must only be replaced by a qualified electrician to avoid any electrical hazards. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
Care and maintenance
For bulb replacement, switch off the product (preferably, isolate it at the distribution board) and allow it to cool down (Caution: bulb gets hot during use). Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
Troubleshooting
When the bulb does not light after installation:
- Please plug in and operate the foot switch to turn your lamp on.
- Please check the bulb.
- Please check the 3 amp fuse in the plug and ultimately check the relevant fuse in your fuse box.
If you have any doubt about the installation/use of this product, consult a qualified electrician. To use this item in Europe, the 3-pin adaptor can be removed by loosening the central screw and removing the adaptor to reveal the 2 pin Europe plug.
Converting 3-pin to 2-pin plug
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>