BG NFB95-01 In line Switches Blank Plates Instruction Manual
- June 13, 2024
- BG
Table of Contents
BG NFB95-01 In line Switches Blank Plates
General Installation Instructions
- If using the new product to replace an old one, note the cable connec- tions and wire up new product in the same way as the old one, with Earthing as stated in these instructions.
- Ensure the mounting box (metal or plastic) for either flush or surface mounting is the appropriate size for the product.
- Route the cable through the most suitable entry point of the mounting box. If a metal box is used a protective cable grommet should be used.
- Strip the cable to the dimensions in the diagram.
- Connect the inner conductor under the central plate and screw. Se- curely clamp the screening braid under the clamp, ensuring that there are no loose conductor strands that may cause short circuits. To assist with the correct installation of this product please consult the wiring diagram.
- When tightening the screening braid clamp ensure that the cable is firmly gripped and that the inner insulation is not squashed beyond a slight oval shape. Always tighten the terminal screws securely, but do not overtighten them.
- Carefully position the accessory into the mounting box, ensuring that no wires are trapped between the plate and the wall and secure with screws (do not over tighten) then insert screw covers (optional).
- Once work has been completed correctly, the product is ready for use.
Note – If your installation uses a four lug metal mounting box, remove the top and bottom lugs or bend fully back.
Care
- To maintain the high quality appearance of decorative finish switches and sockets, BG Electrical recommend the use of a soft cloth periodically to clean the front face. When installing a decorative product please ensure that the wall is decorated, finished and free of moisture prior to installa- tion.
- BG Electrical recommends avoiding using, but not restricted to, these substances from becoming in contact with the decorative metal front-plates when cleaning or decorating:
- Adhesive tape, including low tack masking tape
- Solvents
- White spirit
- Multi surface cleaners
- Industrial multipurpose cleaning wipes
- Wet wipes
- Using items like those listed above may cause a degrading effect to the front-plates lacquer/plated finish, although the function will remain unaffected.
Additional Advice for Decorative Products
Fixing method varies depending on which product range is supplied. Always
ensure wall surface is reasonably flat and smooth, with no bumps or
projections. Metal frontplates WITH screw fixing holes, fix the unit to the
back box using two fixing screws supplied. All Decorative products MUST have
an earth connection between the frontplate and back box. Frontplates WITHOUT
screw fixing holes. These products comprise main unit with integral gasket,
and frontplate as separate item. Fix unit to back box using two fixing screws
supplied. Clip frontplate onto main assembly, ensuring screwdriver notch is
located bottom right hand corner.
To remove plate, place medium size flat bladed screwdriver in notch and lever
off against gasket.
Technical
ASTA Approved
The ASTA quality mark is evidence that the product has been independently
tested to comply with the relevant clauses of the applicable standards. LIC
No.1020
Environmental Protection
This symbol is known as the “Crossed-out Wheelie Bin Symbol”. When this symbol is marked on a product or battery, it means that it should not be disposed of with your general household waste. Some chemicals contained within electrical/ electronic products or batteries can be harmful to health and the environment. Only dispose of electrical/electronic/ battery items in separate collection schemes, which cater for the recovery and recycling of materials contained within. Your co-operation is vital to ensure the success of these schemes and for the protection of the environment.
Address/Helpline
- Luceco PLC
- Stafford Park 1
- Telford TF3 3BD
- ENGLAND
- (EU) Luceco SE
- C/ Bobinadora 1-5
- 08302 Mataró
- SPAIN
- If you have further technical assistance you can get in touch with our
- Technical Helpline on:
- +44 (0)3300 249 279
- technical.supportabgelectrical.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>