MAAX 105359 Freestanding Bathtub Instruction Manual
- June 4, 2024
- MAAX
Table of Contents
105359 Freestanding Bathtub
Instruction Manual
105359 Freestanding Bathtub
http://t.azon.biz/3rkvZ5
http://t.azon.biz/wrUl0w
View F² Drain Video – Scan QR code with a mobile device
Enjoy the experience
MODEL: 105359 • 105571 • 105742 • 105744 • 105745 • 105756 • 106266 •
106267
Read
all instructions carefully before proceeding.
SAVE THIS GUIDE FOR FUTURE REFERENCE.
IMPORTANT • Record the serial number
**** If the optional F² Drain kit was purchased, please refer to the 10032746
installation guide before installing the bathtub
BEFORE YOU BEGIN
-
Carefully read all the instructions in the manual before beginning the installation.
-
Consult local building codes to make sure the installation complies with standards.
-
Remove the unit from its packaging. Before disposing of it, inspect the unit to make sure it is in good shape.
Should inspection reveal any damage or defect in the finish, contact your distributor. The warranty does not cover damages or defects in the finish once the unit has been installed. MAAX’s responsibility for shipping damages ceases upon delivery of the product in good order to the carrier. All complaints regarding damage due to transport must be made directly to the carrier. -
Place the unit in the bathroom before you start working. Sectional units should be disassembled if necessary. Conserve all nuts and bolts.
-
To protect the unit during installation, we recommend that you lay a piece of cardboard on the bottom.
-
If the unit is covered with polyethylene protective film, do not remove it until installation is complete to grant maximum protection. However, remove the film where two surfaces will be in permanent contact.
-
Install all plumbing and drainage before securing the unit. It is always recommended to have a professional plumber do the plumbing installations. See rough-in information for your model on our website.
TOOLS
REQUIRED
SUPPLIES
SOLD SEPARATELY
Unpacking the unit
STEP 1
Cut the cardboard box so as to keep one side to protect the bathtub while
is upside down. Turn the bathtub upside down. Unscrew the skirt from the
wooden blocks.
** Not all bathtubs have screws and wooden blocks holding the skirt and the
bathtub together.
Remove the skirt. Insert a flat-head screwdriver between the wooden blocks and
the wood plank to remove the blocks.
Follow
all instructions and check them off as you go.
1.1 Check me!
1.2
Check me!
**
**Leveling legs adjustment
**
STEP 2
Place back the skirt in the inverted bathtub. Adjust the legs so that they
exceed the top of the edge of the skirt by 1/8″. You can use a 2×4 to take the
measure as shown.
Bolt leg
installation is only applicable to certain models.
2.1 Check me!
Bathtub skirt and drain positioning
STEP 3
With the help of the bathtub apron or the optional template, mark the center
of the drainage line in relation to the desired position of the bathtub. See
also the rough-in information for your model on our website.
Make sure the floor is level.
Before drilling a hole in the floor for the drainpipe, make sure there
are no hidden elements underneath (pipes, floor joists, heating ducts, or
electrical wires).
Place the bathtub in the previously marked position.
Verify that the bathtub is completely leveled. Use the leveling legs if
needed. Remove the bathtub.
Drill the cutout on the floor for the drain and overflow in the previously
marked position.
** If the user needs a faucet on the same side as the overflow, he must
validate that there is no interference between them.
3.1 Check me!
3.2
Check me!
3.3
Check me!
**
If the user needs a faucet on the same side as the overflow, he must validate
that there is no interference between them.
Installing faucets (NOT INCLUDED)
STEP 4
Faucet elements must be installed in the intended area.
See the technical drawing of your model on our website for model-specific
faucet areas when applicable. Mark the location of the faucets on the unit.
Refer to your faucet installation guide to complete their installation.
** If the user needs a faucet on the same side as the overflow, he must
validate that there is no interference between them.
Drill directly on the finished side, following the faucet installation
instructions.
4.1 Check me!
4.2
Check me!
**
Bathtub preparation and installation
STEP 5
Install the waste and overflow and faucets according to the manufacturer’s
instruction manuals.
For models 105571 (Optik 60”) and 106266 (Ariosa 60″) ONLY:
Standard drainpipe and overflow compatible with end-drain freestanding bathtub
models: 105571 (Optik 60”) and 106266 (Ariosa 60”).
5.1 Check me!
Standard drainpipe and overflow compatible with center drain freestanding
bathtub model: 105742 (Optik 66”) and 106267 (Ariosa 66”).
Apply a silicone seal under the apron (optional).
According to bathroom flooring, use proper screws (not included) to secure the
skirt to the floor.
Make sure the skirt is level.
Add two spacers (example 2×4) on the skirt ends and position the bathtub
inside the skirt. Attach the hot and cold water riser to the plumbing hoses.
The faucet must be connected to 1/2″ flexible hoses of sufficient length
to allow the bathtub to be lifted if needed (25″ or 635mm).
5.2 Check me!
5.3
Check me!
Remove the spacers. Make sure all the legs are in contact with
the ground so that the bathtub is not supported by the skirt (see the cut view
below).
The bathtub must be tested before installation is complete. Fill the bathtub
to the overflow and inspect for leaks. Tighten and loosen connections between
the hoses and motor by hand.
To complete the installation and solidify the bathtub, apply a bead of
silicone along the seam where the bathtub rests against the skirt.
5.4 Check me!
5.5
Check me!
TROUBLESHOOTING
Water accumulates around the drain and the bathtub does not completely empty.
- Check that the installation is leveled and that the bathtub is well supported by the legs. With the help of a level, place it at the bottom of the bathtub, and make sure to have a slight slope towards the drain. If necessary, adjust the legs under the bathtub.
The bottom of the bathtub moves during use.
- The bathtub is not sitting firmly on its base; adjust leveling legs.
Polyethylene film will not come off.
- Use a hair dryer to blow hot air on the surface.
MAINTENANCE
Regular disinfections provide an effective defense against various types of
bacteria susceptible to developing in the deposits that build up over time in
all bathtubs and showers.
For daily maintenance cleaning, use a moist cloth and gentle liquid detergent.
For acrylic surfaces, the occasional use of a special acrylic surface cleaner
such as LUMASHINE® or LUMACREAM® will add luster and protect the finish.
Do not use abrasive cleaners, scrapers, metal brushes, or any items or
products that could scratch or dull the surface.
Paint stains: Use either turpentine or paint thinner.
Joint compound: Use a plastic or wood spatula covered with a damp cloth.
Do not use a metal blade or a metal brush.
If a rubber mat is used, it must be removed immediately after each use.
Ignoring this recommendation will cause damage not covered by the warranty.
Certain types of therapeutic products when added to bath water, or if applied
non-diluted directly in the bath, may damage the unit finish. Test the product
on a small inconspicuous surface prior to use.
LIMITED WARRANTY— UNITED STATES
MAAX Bath Inc. offers an express limited warranty on each of its products.
This warranty extends only to the original owner/end-user for personal
household use. For commercial uses, additional limitations apply.
For access to the product Limited warranty please visit: www.maax.com/us-
warranty
LIMITED WARRANTY — CANADA
MAAX Bath Inc. offers an express limited warranty on each of its products.
This warranty extends only to the original owner/end-user for personal
household use. For commercial uses, additional limitations apply.
For access to the product Limited warranty please visit: www.maax.com/ca-
warranty
www.maax.com
Technical Services
T. 1 877 GET-MAAX (1 877 438-6229)
F. 1 888 361-2045
PRINTED IN CANADA
© 2021 MAAX Bath Inc.
10028753
Documents / Resources
| MAAX
105359 Freestanding
Bathtub
[pdf] Instruction Manual
105359, 105571, 105742, 105744, 105745, 105756, 106266, 106267, 105359
Freestanding Bathtub, Freestanding Bathtub, Bathtub
---|---
References
- MAAX Bathware USA - Sharing Experiences Since 1969
- Price, Payment, and Warranty Terms |MAAX Bathware Canada
- Prix, paiement et conditions de garantie |MAAX Produits de salle de bains Canada
- Price, Payment, and Warranty Terms |MAAX Bathware USA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>