JohnDow Industries JDI-CD21 Oil Container Drainer User Manual
- June 13, 2024
- JohnDow Industries
Table of Contents
JohnDow Industries JDI-CD21 Oil Container Drainer
- Part No. JDI-CD21
- FOR WARRANTY INFORMATION, PLEASE CALL 800-433-0708
- DATE OF PURCHASE: READ AND SAVE THIS MANUAL
- FOR SERVICE ASSISTANCE, CALL 800-433-0708 OR VISIT JOHNDOW.COM
- Rev 12/2022 CD21-MAN
- 151 Snyder Ave. Barberton, OH 44203
Important Product Information
- Read this manual before using this product.
- Please contact your local county environmental health department to understand how to properly dispose of the automotive fluids you generate.
GETTING STARTED
Before assembly, ensure you have all parts according to the contents. If any parts are missing or damaged, contact JohnDow Industries for replacement.
CONTENTS
| Item No. | Description | Qty |
|---|---|---|
| 1 | Drain Box | 1 |
| 2 | Drain Station | 1 |
| 3 | M6 x 100 Threaded Bumper | 2 |
| 4 | Door Brace | 2 |
| 5 | 2 NPT to 42mm Bung Adapter, 3-piece | 1 |
| 6 | 1-1/4 NPT x 6 Extension Tube | 1 |
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED: Pipe Wrench
- Remove all contents from carton and plastic packaging. Open drain doors on Drain Box (1) and remove all components.
OPERATION
- Place empty oil bottles upside down on Oil Container Drainer pegs until all residual oil drains from bottles. Remove bottles and discard.
- Note: the pegs on the doors are for gallon container handles.
- When not in use, close and lock doors to prevent potential fire hazard (Lock not included).
FOR SERVICE ASSISTANCE, CALL 800-433-0708 OR VISIT JOHNDOW.COM
Important Product Information
- Read this manual before using this product.
- Please contact your local county environmental health department to understand how to properly dispose of the automotive fluids you generate.
GETTING STARTED
- Before assembly, ensure you have all parts according to the contents. If any parts are missing or damaged, contact JohnDow Industries for replacement.
CONTENTS
| Item No. | Description | Qty |
|---|---|---|
| 1 | Drain Box | 1 |
| 2 | Drain Station | 1 |
| 3 | M6 x 100 Threaded Bumper | 2 |
| 4 | Door Brace | 2 |
| 5 | 2 NPT to 42mm Bung Adapter, 3-piece | 1 |
| 6 | 1-1/4 NPT x 6 Extension Tube | 1 |
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED: Pipe Wrench
- Remove all contents from carton and plastic packaging. Open drain doors on Drain Box (1) and remove all components.
- Flip drain over. Thread Extension Tube (6) onto drain port. Tighten with pipe wrench.
- Thread Bung Adapter (5) onto used oil tank/drum port.
- Loosen Bung Adapter to slide tube through. Adjust to desired height and hand tighten.
- Thread together Threaded Bumper and Threaded Rod (both #3 in image above).
- Use Threaded Bumpers (3) to slightly angle and support the drain.
- Place Door Braces (4) in the side pockets of the Drain Box angling outward.
- Open Drain doors and place Drain Station (2) into drain box.
OPERATION
- Place empty oil bottles upside down on Oil Container Drainer pegs until all residual oil drains from bottles.
- Remove bottles and discard.
- Note: the pegs on the doors are for gallon container handles.
- When not in use, close and lock doors to prevent potential fire hazard (Lock not included)
FOR SERVICE ASSISTANCE, CALL800-433-0708 OR VISIT JOHNDOW.COM
- FOR WARRANTY INFORMATION, PLEASE CALL 800-433-0708
- DATE OF PURCHASE :——————————–
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>