Proficient Audio Systems W800 In-Wall Speakers OWNER’S MANUAL

June 13, 2024
PROFICIENT AUDIO SYSTEMS

Proficient-Audio-Systems-logo

Proficient Audio Systems W800 In-Wall Speakers

SPEAKER PLACEMENT

  • Before installing your speakers, you should consider their placement carefully, taking into account the location of electrical, plumbing, and other fixtures. Contact your Dealer for assistance if you are unsure of the best location for your particular listening environment.
  • Placement In Wall: When installing your speakers into the wall, the ideal sound will be achieved when the tweeters are placed at ear level or slightly higher and the primary listening area is no closer to the wall than the distance between the speakers themselves.(See Diagram 1)
  • If the speakers are positioned far away from the primary listening area, adjust the pivoting tweeters so they are pointed towards it.

Note: To avoid possible damage to the pivoting tweeters, read the section entitled “SPEAKER ADJUSTMENTS” in this manual prior to performing the tweeter adjustment.

MOUNTING SURFACE PREPARATION

New Construction – Unfinished Walls

A Pre-Construction Bracket, available from your Dealer, may be installed prior to drywall application across studs (up to 24″ on-center) where a speaker will be located. After the hole is cut and the drywall is installed, the speakers are then easily installed fol-lowing the instructions for mounting in “Finished Walls” below. Note: If the speakers are to be mounted more than 24″ on-center, a special “Extra Long Wing” is available from your Dealer.

Finished Walls

Prior to the actual installation of the speakers, it will be necessary to run cables to the speaker locations. See your Dealer for more information about cable installation. After the cable has been properly installed, you are ready to mount the speakers. Following the simple steps listed below will result in a professional-looking installation:

  1. Determine the best area to mount your speakers. This area of the wall should be free of obstructions such as electrical conduits, HVAC ducts, or water lines. This can best be determined by noting the placement of fixtures and gaining access to an attic or crawl space for further analysis of the location of such obstacles.
  2. Find the studs nearest the desired speaker mounting location. We highly recommend using a good stud-finder tool for this procedure. If you are lining up the speakers to some other object or molding in the room, make sure you consider the size of the baffle flange which extends beyond the mounting hole on all four sides.
  3. Mark the hole. A template for setting the hole is provided in the box (along with two paint mask inserts for use when painting). Position the template in the desired position and pencil an outline on the wall.
  4. Cutting the hole. CAUTION: This is the most important part of the entire installation. If you are not certain whether any obstructions exist behind the desired mounting area, you should start by cutting a small hole in the center of your pen-ciled mounting hole with a drywall saw. Cut at a 45˚ angle towards the inside of the hole (See Diagram 2). Cutting the small hole at this angle will make drywall repair much easier as the piece cut out can be installed neatly back into the hole. Once you have determined there aren’t any obstructions in your desired mounting location, start cutting the finished hole at a 90˚ angle to the wall surface.
  5. Add insulation. If the area in the wall is not already insulated, add an adequate amount of insulation material to fill the cavity. If the insulation material used is faced with foil or paper, posi-tion the foil or paper away from the speaker.

SPEAKER ADJUSTMENTS

Your Wall Series speakers come from the factory with the tweeter facing straight out from the baffle. This will result in the overall smoothest response. However, depending on your particular pri-mary listening area, room acoustics, ceiling height, or personal preference, you may find the sound more pleasing by pointing the tweeters in a particular direction. If additional treble is desired in the primary listening area, point the tweeter towards that area; and if less treble is required, point the tweeter away. When used in a home theater environment as side or rear channel speakers, the best result will be obtained by pointing the tweeters toward an adjacent wall. Push gently at the edge of the tweeter to point it in the desired direction. (See Diagram 3)

CAUTION: Avoid touching metal dome tweeters, as damage may occur (W680, W690, W800 & W850).

Tweeter Adjustment (W680, W690, W800 & W850):

The switch labeled TREBLE allows for 3dB of treble adjustment. Your speakers were shipped with the treble switch in the “–” position, providing the most linear frequency response. If you desire more treble, move the switch to the “+” position, and the tweeter will play 3dB higher. To return to the neutral setting, push the switch back to the “–” position. (See Diagram 4)

Woofer Adjustment (W680, W690, W800 & W850):

The switch labeled BASS allows for 3dB of bass adjustment. Your speakers were shipped with the bass set to “–”. This setting provides the flattest bass frequency response. If you desire more bass, push the switch to the “+” position and the bass will play 3dB higher. To return to the neutral setting, push the switch back to the “–” position. (See Diagram 4)

SPEAKER INSTALLATION

The unique integral six-foot mounting system incorporated into each Wall Series speaker allows for a quick installation by following these easy steps:

  1. Remove the grille. It may be necessary to push one or two of the mounting screws and its attached foot towards the baffle and against the inside surface of the grille to force the grille out of its retaining groove.

  2. Attach the speaker cable (observing the proper polarity with your amplifier, + to + and – to –). Make sure the left channel of the amplifier is connected to the left speaker and the right channel is connected to the right speaker.

  3. Make sure the mounting feet are turned inward to clear the opening and insert the speaker into the wall. Position the speaker into the hole.
    Note: The flange of the speaker is designed to flex and conform to any small imperfections in the wall’s surface. Tighten the six screws on the front of the baffle only enough to make the flange become snug against the wall. As you tighten the screws, the feet will automatically flip into an outward position (See Diagram 5), thereby clamping the drywall between the feet and the flange. CAUTION: Over-tightening may warp the baffle, crack the wall, cause the flange to distort, and make the grille difficult to install.

  4. Push the grille firmly into the slot in the speaker baffle.

PAINTING THE SPEAKERS

  • If you plan to paint your speakers, we recommend that it be done prior to installation. If you plan to paint your speakers sometime in the future, it is best to remove them by simply reversing the steps for “SPEAKER INSTALLATION” above.
  • If it is necessary to paint the speakers when they are in the wall, the paint masks provided in the carton must be installed between the grille and flange while they are being painted with the wall.
  • Before painting your speakers, remove the material under the grilles. Once the speakers have been painted, return the material back into place.
  • Great care should be taken not to clog the holes of the grille, as this will reduce the sound quality of the speakers.
  • Proficient Audio Systems recommends only light spray painting using 5 parts thinning agent to 1 part paint.

SPEAKER SPECIFICATIONS

W665

  • Speaker Type : 2-Way In-Wall
  • Woofer : 6½” Polypropylene Cone with Rubber Surround
  • Impedance : 8 Ω
  • Sensitivity : 90dB 1W/1m
  • Contour Switches : None
  • Frequency Response : 45Hz – 20kHz
  • Power Handling : 75 watts
  • Dimensions (H x W x D) : 12¼” x 83⁄16″ x 33⁄16″
  • Wall Cut Out (H x W) : 10 7/8″ x 6 3/4″

W670

  • Speaker Type : 2-Way In-Wall
  • Tweeter : Pivoting 1″ Silk Dome
  • Woofer : 6½” Polypropylene Cone with Rubber Surround
  • Impedance : 8 Ω
  • Sensitivity : 91dB 1W/1m
  • Contour Switches : None
  • Frequency Response : 36Hz – 20kHz
  • Power Handling : 100 watts
  • Dimensions (H x W x D) : 12¼” x 83⁄16″ x 31⁄8″
  • Wall Cut Out (H x W) : 10 7/8″ x 6 3/4″

W680

  • Speaker Type : 2-Way In-Wall
  • Tweeter : Pivoting 1″ Aluminum Dome
  • Woofer : 6½” Graphite Cone with Rubber Surround
  • Impedance : 8 Ω
  • Sensitivity : 92dB 1W/1m
  • Contour Switches : Front-Mounted 2-Position +3dB Bass & Treble Switches
  • Frequency Response : 32Hz – 22kHz
  • Power Handling : 125 watts
  • Dimensions (H x W x D) : 12¼” x 83⁄16″ x 33⁄16″
  • Wall Cut Out (H x W) : 10 7/8″ x 6 3/4″

W690

  • Speaker Type : 2-Way In-Wall
  • Tweeter : Pivoting 1″ Aluminum Dome
  • Woofer : 6½” Kevlar Cone with Cast Magnesium Basket and Rubber Surround
  • Impedance : 8 Ω
  • Sensitivity : 92dB 1W/1m
  • Contour Switches : Front-Mounted 2-Position +3dB Bass & Treble Switches
  • Frequency Response : 32Hz – 22kHz
  • Power Handling : 150 watts
  • Dimensions (H x W x D) : 12¼” x 83⁄16″ x 33⁄16″
  • Wall Cut Out (H x W) : 10 7/8″ x 6 3/4″

W800

  • Speaker Type : 2-Way In-Wall
  • Tweeter : Pivoting 1″ Aluminum Dome
  • Woofer : 8″ Graphite Cone with Rubber Surround
  • Impedance : 8 Ω
  • Sensitivity : 92dB 1W/1m
  • Contour Switches : Front-Mounted 2-Position +3dB Bass & Treble Switches
  • Frequency Response : 28Hz – 22kHz
  • Power Handling : 150 watts
  • Dimensions (H x W x D) : 14 7/8″ x 10 1/8″ x 3 3/4″
  • Wall Cut Out (H x W) : 13 5/8″ x 8 3/4″

W850

  • Speaker Type : 2-Way In-Wall
  • Tweeter : Pivoting 1″ Aluminum Dome
  • Woofer : 8″ Kevlar Cone with Cast Magnesium Basket and Rubber Surround
  • Impedance : 8 Ω
  • Sensitivity : 92dB 1W/1m
  • Contour Switches : Front-Mounted 2-Position ±3dB Bass & Treble Switches
  • Frequency Response : 28Hz – 22kHz
  • Power Handling : 175 watts
  • Dimensions (H x W x D) : 14 7/8″ x 10 1/8″ x 3 3/4″
  • Wall Cut Out (H x W) : 13 5/8″ x 8 3/4″

LIMITED TEN-YEAR WARRANTY

Proficient Audio Systems warrants to the original retail purchaser only that this product will be free from defects in materials and workmanship for a period of ten years, provided the speaker was purchased from a Proficient Audio Systems Authorized Dealer.

Defective products must be shipped, prepaid, and insured, together with proof of purchase, to the Proficient Audio Systems Authorized Dealer from whom they were purchased, or to Proficient Audio Systems at the address listed on this installation instruction manual. Freight collect shipments will be refused. It is preferable to ship this product in the original shipping container to lessen the chance of transit damage. In any case, the risk of loss or damage in transit is to be borne by the purchaser.

If, upon examination at the Factory or Proficient Audio Systems Authorized Dealer, it is determined that the unit was defective in materials or workmanship at any time during this warranty period, Proficient Audio Systems or the Proficient Audio Systems Authorized Dealer will, at its option, repair or replace this product at no additional charge, except as set forth below. If this model is no longer available and cannot be repaired effectively, Proficient Audio Systems, at its sole option, may replace the unit with a current model of equal or greater value. In some cases where a new model is substituted, a modification to the mounting surface may be required. If mounting surface modification is required, Proficient Audio Systems assumes no responsibility or liability for such modification. All replaced parts and product become the property of Proficient Audio Systems. Products replaced or repaired under this Warranty will be returned to the original retail purchaser, within a reasonable time, freight prepaid.

This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of the product which has not been authorized or approved by Proficient Audio Systems. This Warranty also excludes normal cosmetic deterioration caused by environmental conditions. This warranty will be void if the Serial Number on the product has been removed, tampered with or defaced.

This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above, the purchaser’s sole remedy shall be repair or replacement as provided above. In no event will Proficient Audio Systems be liable for any incidental or consequential damages arising out of the use or inability to use the product, even if Proficient Audio Systems. or a Proficient Audio Systems Authorized Dealer has been advised of the possibility of such damages, or for any claim by any other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply.

All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow limitations on the length of an implied warranty. If the original retail purchaser resides in such a state, this limitation does not apply.

For technical inquiries, please don’t hesitate to contact us:

Our dedicated support team is available to assist you on every weekday, excluding holidays, from 7:00 a.m. to 5:00 p.m. PST. Feel free to reach out whenever you need assistance.

  • Address: 940 Columbia Avenue, Riverside, CA 92507
  • Phone: 800.448.0976
  • Fax: 951.787.8747
  • Website: proficientaudio.com

Please feel free to reach out to them for any inquiries or assistance you may need.

FAQs

What is the maximum power handling capacity of the Proficient W800 In-Wall Speakers?

The Proficient W800 In-Wall Speakers have a power handling capacity ranging from 5 watts to 150 watts.

What is the size of the subwoofer in these speakers?

These speakers feature an 8-inch injection-molded graphite woofer with a rubber surround for delivering robust bass.

Can the tweeter be adjusted for directing sound in a specific direction?

Yes, the speakers come with a 1-inch aluminum dome pivoting tweeter that can be adjusted or pivoted to direct sound precisely where you want it.

What is the impedance (Ohm rating) of the Proficient W800 In-Wall Speakers?

The impedance of these speakers is 8 Ohms.

What is the frequency response range of these speakers?

The frequency response of the Proficient W800 In-Wall Speakers ranges from 28 Hz to 22 kHz, ensuring a wide range of audio frequencies are reproduced.

Are these speakers suitable for in-wall installation?

Yes, these speakers are designed for in-wall installation, making them ideal for home theater setups or discreet audio installations.

What are the product dimensions and weight of the Proficient W800 In-Wall Speakers?

The speakers have dimensions of 16.5 x 11.5 x 10.25 inches and weigh approximately 15.6 pounds.

Can these speakers handle high-power audio output?

Yes, these speakers are capable of handling up to 150 watts of maximum output power, making them suitable for high-quality audio setups.

What is the model name and brand of these in-wall speakers?

The model name is W800, and the brand is Proficient.

Can these in-wall speakers be used as part of a surround sound system?

Yes, the Proficient W800 In-Wall Speakers are designed for use as surround sound speakers, making them an excellent choice for home theater setups.

Are these speakers easy to install in a wall?

Installing these speakers in a wall typically requires some DIY skills and knowledge of wiring. If you're not comfortable with installation, it's advisable to seek professional help.

Can I paint or customize the speaker grilles to match my room's decor?

Yes, you can often paint or customize the speaker grilles to match your room's decor. However, it's essential to follow the manufacturer's recommendations for painting to avoid affecting sound quality.

Download This PDF Link: Proficient Audio Systems W800 In-Wall Speakers OWNER’S MANUAL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals