nauto ADAS-2000 Predictive ADAS Plus DMS Installation Guide

Installation Guide

Nauto® 3 Device & MarkButton

OBD Installation

US Installation Guide
July 2021

Overview

PURPOSE

The purpose of this document is to provide guidelines for the installation of the Nauto 3 Device. The installation guidelines, specifications, materials and examples provided in this document are for information purposes only, are non- exhaustive, and must not be relied upon for the specific installation in any vehicle. This guide is not intended to replace any regulatory requirements in the jurisdiction where the Nauto 3 Device is installed or used.

Before starting the Nauto 3 Device installation and configuring the system, please ensure that you have read this guide thoroughly. If you have any questions or concerns regarding the installation of the Nauto 3 Device, please contact Nauto Support at 1 888-628-8690 or support@nauto.com.

WARNING

This equipment may only be located in a position where it cannot interfere with the normal and safe operation of the vehicle, or present a hazard to the driver, or passengers. When routing all cables ensure that the insulation does not become worn or damaged. All cabling must be secured utilizing industry standard methods.

If you are unsure about the placement or installation of this equipment, stop work, and contact your Nauto representative immediately.

Under no circumstances should any part of the Nauto system be installed inside the engine compartment area.

This equipment should not be operated in hazardous environments, or in areas that contain explosive materials or flammable vapors.

This equipment should not be operated in aircraft or in close proximity to medical equipment.

Unauthorized changes or alterations to the equipment may invalidate the Nauto warranty, and may also affect the vehicle manufacturer’s warranty.

DISCLAIMER & SAFETY INFORMATION

Due to ongoing development, information and specifications may change at any time without notice. While the information is believed to be accurate, it may include errors or inaccuracies. Nauto shall not be liable for any use of this installation guide or information supplied in it.

The installation of the Nauto 3 Device may adversely affect other vehicle components or safety equipment. Nauto assumes no responsibility and disclaims any liability for any damage to any vehicle components or safety equipment, or bodily injury, that may arise due to installation or use of Nauto’s products and services.

THE INFORMATION IN THIS INSTALLATION GUIDE IS PROVIDED “AS IS” AND TO THE EXTENT PERMITTED BY LAW, IS PROVIDED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT.

Nauto shall not be liable for any damages, losses, costs or expenses, direct, indirect or incidental, consequential or special, resulting from the use of this installation guide.

This guide is not written for any specific vehicle since the proper wiring and installation of electronics differs for each vehicle. Installation should be completed by qualified individuals who are trained to wire electronics such as the Nauto 3 Device. It is your responsibility to know how to wire in electronics such as the Nauto 3 Device for your specific vehicle. Improper wiring may cause injury or damage and void the warranty. Any changes or modification to the Nauto 3 Device not expressly approved by Nauto or the entity responsible for compliance may void any warranties and your authority to operate the Nauto 3 Device.

This installation guide contains proprietary information that is protected by copyright. All rights are reserved. This guide may not be copied, reproduced, or translated into another language without Nauto’s prior written consent.

Installation Tool List

The following tools are recommended to perform installation ofthe Nauto Device:

 T5 Torx driver with handle

 Smartphone or tablet with wireless or wifi Wire crimpers

 Trim panel removal too

Nauto Components

1. Nauto 3 Device

2. Windshield Mounts

3. Mark Button

This is optional and may not be included. If included, do not dispose of small bag with “MAC address” label.

4. Power Cable
   2 versions: hardwire and OBD
   

5. OBD Adapters
   See reference guide on page7
   

6. OBD Y-Cable
   This is optional and may not be included

Nauto Components | OBD Adapter Reference

The OBD adapters included with the Nauto 3 Device allow technicians to install the included Y cable. Use the following adapter reference guide and included instructions to install the Y cable for the Nauto 3 Device.

North American FlangeMount

• Ford
• GM
• Chrysler

North American Extended FlangeMount

• Ford

North American Snap-InMount

• Chrysler

North American Side & LockMount

• Ford
• GM

European LockMount

• Mercedes
• BMW

AsianSnap-In

• Toyota
• Hyundai
• Kia
• Ford

European Latch &Snap

• Fiat
• Citroën
• Peugeot

VWSnap-In

• Volkswagen
• Audi

BMW Slide &Lock

• BMW

Ford RoundSnap-In

• Ford

Iveco Slide &Lock

• Iveco

Volvo SlideMount

• Volvo

Installation | OBD Connection

OBD Port Connection (without Y-Cable)

1. Locate the OBD port within the vehicle, removing vehicle panels, as necessary.
2. Insert make end of the Nauto OBD power cable into the vehicle’s OBD port

After making proper power and ground connections, properly secure all loose and extra wiring.

OBD Port Connection (with Y-Cable)

1. Locate the OBD port within the vehicle,removing vehicle panels, as necessary.
2. Gently remove the factory OBD plug from the mount.
3. Select and install the vehicle-appropriate adapter from Nauto’sOBD Adapter Kit (page 6).
4. Using the appropriate adapter,replace the vehicle’s OBD port with the female end of the Nauto Y-cable.
5. If there was an existing device in the vehicle’s OBD port, please reconnect it utilizing the Nauto Y-cable.
6. Plug the male end of the Nauto Y-cable into the vehicle’s OBD port.
7. Zip tie all connections to help ensure plugs will not disconnect.

After making proper power and ground connections, properly secure all loose and extra wiring. A slot built into the side of the power supply unit can help to secure excess wiring to conceal and secure the wires of the harness, and trim or bundle up unused wires.

Installation | Power Cable Connection

Power Cable Connection

1. Locate the power end of the power cable, or the end with the small black block (see image for reference).

2. Leave 8-10″ of the cable exposed at the rearview mirror and route the cable safely and securely to the power supply unit.

3. One way to do so that may be appropriate is as follows:
   a. Start tucking the cable under the windshield headliner starting just above the rearview mirror.
   b. The cable should be buried under the headliner so that it will not slide out or drop from the headliner.
   c. Route the cable to the left (driver’s side of the vehicle) and remove the A-pillar panel to route the cable around, behind, and away from all airbag components and related vehicle accessories.
   d. Pull the door gasket away from the body of the vehicle and run the power cable into the channel near the pinch weld, but without crossing over the pinch weld, towards the power supply unit.

4. Bundle and secure all excess wiring so it will not interfere with vehicle and driver controls.

5. Mount the bundled cable in a secure location under the dash of the vehicle with zip ties.

1. Power end of powercable

Installation | Device Registration

Download the Nauto InstallerApp
from the App Store or Google Playstore.

1. Login.

Please use the login credentials provided to you previously to access the Nauto installer app.

2. Select “New Installation”.

3. Scan QRCode.

The QR code is located on the device. You may also manually enter the serial number,which is located next to the QR code on the NautoDevice.

4. Review and confirm the fleet name.

Installation | Device Installation

5. Perform the installation

6. Take photo of connection and confirm

Take a clear unobstructed photo of the power connections made if hardwired. If connected via OBD, take photo of OBD connection. Once taken the app will ask you to confirm the photo.

1. Connect the Nauto Device to power.
Insert the power cable end that extends from under the headliner into the device’s power port. The Nauto Device will now boot up.

2. Check for green lights on the device.
This can take up to one minute. Blue lights will appear on the device first, meaning the device is updating software, followed by two green lights.

3. Fit the windshield mount to the back of the Nauto Device.
Do not remove the adhesive backing at this time.

4. Review live images from the NautoDevice.
The Nauto Installer app will show live images from both interior and exterior cameras. This can take a few minutes.

5. Determine the optimal mounting location.
This is based on the live images and recommended locations (see image on right).

6. Locate the small screw on the accessible side of the device. Find this on the exposed side from the rearview mirror. Rotate the T5 screw clockwise to lock the Nauto Device into place. The other screw will not be tightened.

7. Mark the location for the Nauto device.
Using the provided measurements and live images as guidance, mark the location for he Nauto device on the windshield with tape or marker. This marked location should be at the bottom of where the bracket will be placed to give you a reference point to place the bottom of the bracket. For optimal device performance:

a. The forward-facing camera should have a clear view of the front of the vehicle with no obstructions.

b. The forward-facing camera should not be blocked by window tint or metal film found near the rearview mirror. If neither side of the rearview mirror will produce the desired result, please contact Nauto for additional options.

c. The driver-facing camera should not be easily obstructed by the driver-side visor or other OEM and aftermarket equipment.

d. The cameras should not block any sensors or rearview mirror functions.

Recommended mounting locations

Camera views during installation

7. Images from the device
The app will now communicate with the device to get live images to help properly align the device. See next page for more details.

8. Clean the desired location using the provided swab.
Dry the area with a clean paper towel, removing all film and residue.

9. Peel the liner from the adhesive on the windshield mount.

10. Slowly align the device into position.
Check the live images on the app. If your view is properly aligned, gently press the whole assembly to the windshield.
– Please ensure that the top of the Nauto device is not touching the headliner
– If necessary for optimal placement, only allow a portion of the adhesive to be on the frit/metallization

11. Press and hold.
Press and hold the complete mount to the windshield for at least 15 seconds. 15 seconds is the minimum time for the adhesive to adhere properly. Failure to properly secure the Nauto Device may cause it to detach from the windshield, which may lead to catastrophic damage or injury.

12. Verify the mount and Nauto Device are securely attached.
From the outside of the vehicle, verify that the bracket adhesive is completely attached. Press and hold for an additional 15 seconds if not. Please see picture to right for how adhesive should look from the outside.

13. Secure all dash panels.
Make sure all cables are secure and out of the driver’s view and movement.

Interior view of NautoDevice

Exterior view of NautoDevice

1. Poor attachment
2. Good attachment

Installation | Vehicle Information

8. Scan the VIN barcode.

The barcode is located in the vehicle.

9. Enter the vehicle license plate and vehicle name.

Confirm with the fleet manager the vehicle identifier for Vehicle Name or ID.

Installation | Image Submission

1. Capture installation images.
Follow prompts to capture three images of the vehicle.

1. Install Location
2. License Plate
3. Mount adhesive

2. Complete installation.
Upload images through the Nauto Installer app to complete installation. This will be done via LTE connection, unless you connect to a new Wi-Fi network.

10. Take photo of camera location and confirm

From the driver’s seat, capture a photo of the camera position on the windshield. Once taken the app will ask you to confirm the photo.

11. Take photo of license plate and confirm

From the back/front of the vehicle, capture a photo of the license plate. Once taken the app will ask you to confirm the photo.

12. Take photo of Mount adhesive

From the outside of the vehicle, capture a photo of the mount adhesive. Once taken the app will ask you to confirm the photo.

13. Submit Installation

Once completed, submit the installation for completion.

Installation | Mark Button

The Mark Button is a Bluetooth device that may be included with the Nauto 3 Device. The button is designed to enable drivers to initiate uploads of video to the cloud.

1. Turn Mark Button ON.
Locate the switch on the back side of the device and toggle it to the “On” position. It may take up to 30 seconds for the Mark Button to connect to the Nauto 3 Device via Bluetooth.

2. Confirm connection.
Review the LED light on the Mark Button when pressed. A green LED should activate upon press. The Mark Button will not need to be manually paired to the Nauto 3 Device. When the device has power, and the Mark Button is turned on, press the Mark Button and it should automatically pair with the nearest Nauto 3 Device.

3. Attach the Mark Button.
Using the provided Velcro, attach the Mark Button to the vehicle. Consult the fleet manager for preferred Mark Button placement.

Troubleshooting

1. Items to check if device is not working

• Is the device connected to constant power, switched power, and a ground?
• Is the power cable plugged firmly into the device?
• Is the in-line fuse in working condition?

2. Device LED color meanings

• Green: Device is ready to be installed or has completed installation
• Flashing Green: Device is in install mode
• Orange: No LTE connection
• Red: Possible hardware issue
• Dim red (almost invisible): Device is in night / infrared mode (should not be on if outside in sunlight)

3. Mark Button pairing

• The Mark Button will not need to be manually paired to the Nauto 3 Device. When the device has power, and the Mark Button is turned on, press the Mark Button and it should automatically pair with the nearest Nauto 3 Device. If replacing a Mark Button, you may need to let the Nauto 3 Device go to sleep before waking it back up and pressing a new Mark Button near the device for it to pair to the new button.

4. Cannot connect to device via Wi-Fi

• If you are unable to connect to the Nauto 3 Device with your phone via WiFi, the Nauto app will give you the option to connect via LTE
• Note: you need to have an LTE or separate WiFi connection on your cellular device to finish installation

5. The power LED (visible from outside) turns off when the device goes to sleep when parked/off. Please check for power with ignition on.

6. Resetting the Device. If you are unable to connect to the device and if Nauto support instructions you to do so, you may manually reset the device using a small pointed object such as a paperclip to press the reset button between the + and -­ buttons on the front of the device.

• One press ­- a quick press of this button will reset the device. DO NOT hold this button for long as it will result in a factory reset. Please only do this if instructed to by Nauto support

**Do not manually reset the device unless instructed by the Nauto support team.

Additional Resources

• the12volt.com (www.the12volt.com)
• Bulldog Security (www.bulldogsecurity.com)
• OBD Port Locater (www.fitguide.installernet.com/progressive/progressive.aspx)
• Mitchell 1 (www.mitchell1.com)
• ALLDATA (www.alldata.com)
• Local dealer for vehicle manufacturer

Nauto Inc. is not responsible for, and does not endorse, the content of any linked site. Links are provided only as a convenience.

For any questions or support

     888.628.8690
    support@nauto.com

Nauto Support is available Mon – Fri 6AM – 6PM PST.

© Nauto 2020. All RightsReserved.

References

• Car Alarm, Car Stereo, Mobile Video, and Cruise Control Info for Installers
• OEM Mechanical and Collision Information | ALLDATA
• Progressive OBD-II port locator
• Automotive Repair Software & Repair Shop Solutions | Mitchell 1
• Car Alarm, Car Stereo, Mobile Video, and Cruise Control Info for Installers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>