HELVIA REDY-630SET Speaker Set User Manual

June 13, 2024
HELVIA

HELVIA REDY-630SET Speaker Set User Manual
SET Speaker Set

IMPORTANT SAFETY INSTRUCTIONS

  • Read these instructions
  • Keep these instructions
  • Heed all warning
  • Follow all instructions

Water and Moisture
The apparatus should be protected from moisture and rain and can not be used near water; for example near a bathtub, a kitchen sink, a swimming pool, etc.

Heat
The apparatus should be located away from heat sources such as radiators, stoves or other appliances that produce heat.

Object and Liquid Entry
Objects should not fall and liquids should not be spilled into the inside of the apparatus for safety.

Cleaning
Clean only with a dry cloth. Do not use any solvents such as benzene or alcohol\ as they may damage the surface.

Servicing
Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only. Only use accessories/attachments or parts recommended by the manufacturer

UNPACKING

Thank you for purchasing your REDY-630SET Active+Passive speaker set. All\ units have been rigorously tested before leaving the factory. Carefully unpack the carton and check the contents to ensure that all parts are present and in good conditions:

  • 1x Active Speaker
  • 1x Passive Speaker
  • 1x 1,7m (5.6 ft) Power Cable
  • 1x Remote Control
  • This User manual

If anything is damaged during transport, notify the shipper immediately and keep packing material for inspection. Again, please save its carton and all packing materials. If the unit must be returned to the manufacturer, it is important that the
unit is returned in the original manufacturer’s packing. Please do not take any action without first contacting us. Our productsaresubject to a continuous process of further development. Therefore modifications to the technical features remain subject to change without further notice.

PRODUCT OVERVIEW

The REDY-630SET is the answer to all those small audio amplification needs (small shops, multimedia educational contexts, etc.) where practicality, ease of installation, multi-functionality and compactness need to coexist in perfect harmony.

The system consists of a pair of 2-way ported speakers with 6.5” woofer and 0.5” tweeter. One of the speakers is active and features a 30+30W RMS (100+100W Peak Power) Class-D amplifier and a media player with USB input, Line Stereo\ input and BT streaming. The other speaker is passive and is connected to the first\ speaker to create a perfect stereophonic sound system.

The Line Stereo input is equipped with RCA, 1/8” mini jack and Phoenix connectors, allowing connection to a wide range of portable (CD, DVD, Tuner, etc.), multimedia (mobile phones, tablets, etc.) and fixed sources. The system is also equipped with a stereo Link Out and a mono subwoofer output. This allows the REDY-630SET to be expanded to include additional speakers or sound systems.

BT streaming and remote control also allow wireless operation. Use your own BT devices and access your own playlists. The TWS (True Wireless Stereo) function is also available and lets the user connect to a second REDY-630SET and use the additional active speaker as Right channel or simply as wireless audio link.

Features:

  • 2x30W RMS (2x100W Peak Power) Class-D Power Amplifier
  • 2-Way Ported Speaker with 6.5” Woofer and 0.5” Tweeter
  • C-shaped Brackets with Adjustable Horizontal Angle
  • T/USB/Line-in Player with Remote Control
  • Stereo Line input with RCA, Mini-jack and Phoenix connections
  • 2-Band EQ, Link Out and Sub Out
  • True Wireless Stereo (TWS) function

PRODUCT APPEARANCE

Front Panel
Front Panel
Rear Panel
Rear Panel

  1. 3.5mm Stereo Aux input

  2. Stereo LINK output

  3. Mono SUB output

  4. R-SPEAKER output

  5. LED indicator

  6. USB Drive input

  7. RCA Stereo/Mono input

  8. Line In balanced input

  9. Treble control knob

  10. Bass control knob

  11. Volume control knob

  12. Loop button

  13. Mode button

  14. Skip Backwards/Rewind button

  15. Skip Forward/Fast-Forward button

  16. Play/Pause/ TWS pairing button

  17. Power switch

  18. Power supply input

  19. 1. 3.5mm Stereo Aux Input
    3.5mm stereo TRS input for external audio sources such as CD/MP3 player, laptops, smartphones or tablets.

  20. Stereo LINK Output
    3.5mm stereo LINK output for connection to another active speaker or amplifier.

  21. Mono SUB Output
    3.5mm mono SUB output for connection to a subwoofer.

  22. R-SPEAKER Output (Euroblock)
    2-pin Eurobolck speaker output for connection to the passive speaker. Please refer to section “5.2. Speaker Connection” at page 10 for information on how to\ connect speakers.

  23. LED Indicator
    This LED lights up in blue when the active speaker is turned on.

  24. USB Drive Input
    Supports up to 32GB USB flash drives formatted in FAT 32 file system. Supports audio formats such as FLAC, WMA, WAV and high quality MP3 (up to 320 kbps).
    Note: Audio from the USB drive starts playing as soon as the drive is inserted and will have priority over any other audio source.

  25. RCA Stereo/Mono Input
    RCA stereo or mono unbalanced input for external Line level sources such as smartphones or laptops. Press the MODE button, (“13. Mode Button” at page 8), to select this input.

  26. Line In Balanced Input (Euroblock)
    Euroblock Line input for balanced connections. Please pay attention to the polarity of the wires (+=Hot, -=Cold, G=ground).

  27. Treble Control Knob
    This knob increases or decreases the high frequency response. The 0 position (middle) produces a flat response. Control range goes from -12 dB to +12 dB.

  28. Bass Control Knob
    This knob increases or decreases the low frequency response. The 0 position (middle) produces a flat response. Control range goes from -12 dB to +12 dB.

  29. Volume Control Knob
    This knob adjusts the output volume level.

  30. Loop Button
    This button is not used in this version.

  31. Mode Button
    Short press to switch between different audio sources connected to the active speaker. When switching to BT Mode, there will be a quick, short sound at first, then a longer ascending sound after about 10 seconds, indicating that your device is now paired with the speaker. Now press Play/Pause “ ” on the active speaker (or on\ your device) to start playback.
    Note: this process is done anytime you switch to BT mode from another source. Please refer to section “5.3. BT Mode Pairing” at page11 for more information on connecting your device via BT for the first time.
    Note: If you are unable to hear any audio when switching from one source to another, make sure the audio from the selected source is not paused.

  32. Skip Backwards/Rewind Button
    In BT and USB mode, press once to play previous track. Press and hold to rewind. This button does not work in AUX and RCA mode, please use the controls on yourdevice for these functions.

  33. Skip Forward /Fast-Forward Button
    In BT and USB mode, press once to play next track. Press and hold to fast- forward. This button does not work in AUX and RCA mode, please use the controls on your device for these functions.

  34. Play/Pause / TWS Pairing Button
    Short press to start/pause audio playback in BT and USB mode. In AUX and RCA mode, this button only mutes audio but does not pause it. Use the play/pause function on your connected device to pause and resume playback.
    If you want to use the TWS (True Wireless Connection), make sure two activespeakers are turned on and in BT Mode, then press and hold the TWS button for3 seconds on any one of the speakers. Two active units will now be connected automatically.

  35. Power Switch
    Use this switch to turn the speaker on or off.

  36. Power Supply Input
    Connector for mains power

INSTALLATION

Read these instructions carefully before installing and using the product.

  1. Prior to installing the speaker into any wall, check the structure for weight bearing ability and avoid contact with any wiring or plumbing that might be behind the surface area. Installing on soft materials or in areas incapable of supporting the speaker’s weight may cause personal injury or damage to the speaker.
  2. Make sure the speaker is properly secured to the wall. Please use the proper screws, bolts, or anchors. Failure to do so may cause the speaker to become unsecured and cause potential damage/injuries.
  3. When installing the speakers outside, choose areas such as the underside of eaves to avoid strong direct sunlight that may affect the color and life of the speaker enclosure.
  4. Use only approved and certified wiring in your installation. Do not stretch or place the wire in contact with sharp objects.
  5. Before removing the cables, make sure the amplifier and other components are switched off.
  6. Damage to the woofer and tweeter may occur if the speaker is dropped orhit, resulting in distorted sound or no sound at all.
  7. Never overdrive your speaker to the point of distortion and always reduce volume prior to switching input sources.

Speaker Installation
The hardware equipment listed below is needed to install the speaker:

  • Wire Strippers

  • Screwdriver

  • Tape Measure

  • Stud Finder (for wood stud wall

  • Ladder

  • Screws x4

****The installer is responsible for the installation. Please make sure to\ install speakers according to local safety regulations.

****When handling these speakers, be careful not to touch the speaker net, otherwise there is a risk of deforming it

Speaker Connection
Speaker Connection

  • Make sure that the active speaker is unplugged from the mains before making any connection.
  • Connect active and passive speaker as shown above, please make sure that there polarity is not inverted (+ connected to -). If the polarity of the speakers is reversed, the sound will be unnatural and will play without bass

Note: Anytime you note distortion, reduce the volume to a lower level. Never allow the amplifier to be driven into “clipping”, otherwise the speakers may be damaged. Damage caused by operating the speakers at distorted volume levels is not covered by the warranty.

BT Mode Pairing

BT Mode allows connection of a smartphone, PC or tablet to the active speaker for playback of stored files or streamed digital audio. In order to enable this function make sure that the speaker is turned on and proceed as follows:

  1. Press the MODE button, “13. Mode Button” at page 8, to enter BT mode. A quick, ascending sound is played, indicating that the speaker is in BT mode and ready for pairing.
  2. Open the Settings menu on your external device and enable BT connection.
  3. Search for “REDY-630” on the list of devices and click to pair with the speaker.
  4. The speaker will emit a longer and sharper ascending sound, indicating that your device is now paired.
  5. To unpair the speaker, open the BT menu on your device, select “REDY-630” from the list, and choose “unpair”. The speaker will emit a different sound indicating that your device is now unpaired.
  6. Repeat the above process if you want to pair your device again or if pairing fails. If you are unable to reconnect a previously connected device, remove the “REDY-630” from the list of paired devices and follow the above instructions from the start.

Note: BT input has the priority over the RCA input when both BT and RCA are connected simultaneously. To listen to audio from the RCAinput make sure all BT devices are disconnected, or select it via the MODE button .

Note: One device can be connected via BT to one speaker only. If youwant to pair a different device to the same speaker, disconnect the one previously paired first.

Note: BT connection will be lost if the distance between the speaker and the paired device is longer than 10m (32.8 ft.).

Remote Control

Remote Control| **** 1.| **** On/Off Button: Press this button to put the speakers in stand- by. Audio is muted but speakers are still powered. Press again to resume playback. In RCA and AUX mode, audio is muted but playback continues on your connected device. In BT and USB mode, playback is paused and then resumed from the same point. When re- suming in BT mode, the device will be paired again as described in point “13. Mode Button” at page 8.
---|---|---
Note: Numbers and RPT button are not used.| 2.| Mode Button: Same functions as point “13.Mode Button” at page 8.
| 3.| Stop Button: Press this button to stop play- back. Press the Play/Pause button to resume the audio from the start.This button works only in USB mode.
| 4.| Volume Up Button: Press repeatedly toincrease volume in steps, or keep pressed toincrease it continuously.
| ****
5.| Skip Backward/Rewind Button: in BT and USB mode, press once to skip to previous track or press and hold to rewind.This button does not work in AUX and RCAmode.
| 6.| Play/Pause Button: in BT and USB mode, press once to play/pause playback. In AUX and RCA mode, audio is muted but playbackis not paused.
| 7.| Mute Button: Press to mute/unmute audio.Playback is not paused.
| ****
8.| Skip Forward/Fast-Forward Button: in BT and USB mode, press once to skip to next track or press and hold to fast-forward.This button does not work in AUX and RCAmode.
| 9.| Volume Down Button: Press repeatedly todecrease volume in steps, or keep pressed todecrease it continuously.
| 10.| EQ Button: Press to choose between equal-ization presets.
Model| REDY-630SET
---|---
Speaker Type| 2-Way Active Speaker| 2-Way Passive Speaker
Frequency Response| 70 Hz – 20 kHz @ -10 dB| 70 Hz – 20 kHz @ -10 dB
Max SPL| 104 dB@ 25W| 104 dB@ 25W
Sensitivity| 90 dB| 90 dB
HF Type| Mylar Dome Tweeter| Mylar Dome Tweeter
Voice coil Diameter| 0.5”| 0.5”
Directivity (HxV)| 100° x 100°| 100° x 100°
Crossover Frequency| 7.0 kHz| 7.0 kHz
Woofer Diameter| 6.5”| 6.5”
Cone Material| Paper Cone rubber edge| Paper Cone rubber edge
Voice coil Diameter| 1.0 inches| 1.0 inches
Impedance| 8 ohm| 8 ohm
Amp Class| Class-D|
RMS Power| 30 W| 30 W
Peak Power| 100 W| 100 W
Inputs| 1/8” Stereo Jack, Stero RCA, 5-pinPhoenix| Binding Post (Red/Black)
**** Outputs| 1/8” Stereo Jack (Link Out), 1/8” Mono Jack (Sub Out), 2-pin Phoenix(Right Speaker Out)|
Line/Aux/RCA controls| Volume|
EQ Treble| Cut-off freq: 20kHz|
| Gain: +/- 12dB|
EQ Bass| Cut-off freq: 20kHz|
| Gain: +/- 12dB|
LED| Power On (Blue)|
Multimedia Player controls| Mode, Song +/-, Rew, FF, Play/Pause, TWS|
Power Requirement| 100-240 Vac – 50-60Hz|
Power Consumption| 100W|
Fuse| T2A-250V|
Housing Material| Polypropylene| Polypropylene
Grille Material and Thickness| 0.6 mm, Steel| 0.6 mm, Steel
---|---|---
Wall-mount| C-Bracket with horizontal adjust- ment| C-Bracket with horizontal adjust- ment
Product Size (WxDxH)| 215 x 197 x 298 mm (13.2 x 14.8 x11.7 in)| 215 x 197 x 298 mm (13.2 x 14.8 x11.7 in)
Speaker Weight| 3.8 kg (8.4 lbs.)| 3.8 kg (8.4 lbs.)
Packing Size – Pair(WxDxH)| 483 x 288 x 345 mm (19.0 x 11.3 x13.6 in)| 483 x 288 x 345 mm (19.0 x 11.3 x13.6 in)
Packing Weight| 7.7 kg (17.0 lbs.)| 7.7 kg (17.0 lbs.)

Our products are subject to change.Modifications to technical features remain subject to change without notice.

WARRANTY AND SERVICE

All HELVIA® products are covered by warranty according to European regulations (2 years in the case of purchase by private person – B2C; 1 year in the case of purchase by company – B2B). The warranty is valid from the date of purchase by the end user (private individual or company), indicated in the purchase document (receipt in the case of private person; invoice in the case of company). The following cases / components are not covered by the above warranty:

  • All accessories supplied with the product;
  • Improper use;
  • Failure due to wear and tear;
  • Any unauthorized modification of the product by the user or third parties

HELVIA must meet the warranty obligations due to any non-compliant materials or manufacturing defects, by remedying free of charge at HELVIA’s discretion by either repairing orreplacing specific parts or the entire equipment. Any defective parts removed by a product in the event of a warranty claim become property of HELVIA. During the warranty period, defective products can be returned to HELVIA retailer or installer with proof of original purchase (receipt or invoice). To avoid damage during transport, please use the original packaging, if available. For more information, visit the website: www.frenexport.com.

WARNING

READ CAREFULLY – only for EU and EEA (Norway, Iceland and Liechtenstein).

This symbol indicates that the product must not be disposed of with household waste, according to the WEEE directive (2202/96/EC and subsequent amendments) and national legislation.

The product must be delivered to a designated waste collection center (e.g. on an authorized one-for-one basis when you buy a new similar product, or to an authorized collection site for recycling waste electrical and electronic equipment). Improper handling of this type of waste can have a negative impact on the environment and human health due to potentially dangerous substances that are generally associated with electrical and electronic equipment. At the same time, your cooperation in the properdisposal of this product will contribute to the effective use of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service.

This product is imported in the European Union by
Questo prodotto è importato nell’Unione Europea da

FRENEXPORT SPA – Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy
HELVIA® is a registered trademark of FRENEXPORT SPA – Italy
HELVIA® è un marchio di fabbrica registrato di FRENEXPORT SPA – Italia

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HELVIA User Manuals

Related Manuals