ENDON 106282 Ridgeton 3 Light Ceiling Pandant User Guide
- June 13, 2024
- ENDON
Table of Contents
ENDON 106282 Ridgeton 3 Light Ceiling Pandant
Product Information
The Pendant Light Fitting is a ceiling light suitable for domestic use. It is designed to be connected to a 220-240V~ 50Hz power supply in accordance with current IEE wiring regulations. The product should be installed in compliance with local building regulations and is intended for use in ceilings only, excluding bathroom locations. It is important to note that no objects should be placed on or hung from any part of the product. Additionally, it is crucial to avoid fitting bulbs with a higher wattage than specified on the label, as this may cause overheating and damage to the fitting. The product should be handled with care and maintained properly. When replacing bulbs, ensure that the product is switched off and allowed to cool down. Cleaning should be done using a dry cloth and liquid or abrasive cleaners should not be used.
Product Usage Instructions
- Before installation, carefully read through the safety instructions provided in the manual.
- If you are unsure about the installation process, consult a qualified electrician for assistance.
- Ensure that the power supply is disconnected before starting the installation.
- Follow the assembly instructions provided in the manual to correctly assemble the pendant light fitting.
- Make sure all electrical connections are tight and there are no loose strands left out of the terminal.
- Install the pendant light fitting in accordance with local building regulations and ensure it is suitable for ceiling use only.
- Never place any objects on or hang anything from the pendant light fitting.
- When replacing bulbs, switch off the product and allow it to cool down before proceeding.
- Clean the pendant light fitting using a dry cloth. Do not use liquid or abrasive cleaners.
- If the bulb does not light after installation, check for electricity failure and ensure all connections are secure.
- If you have any doubts about the installation or use of the product, consult a qualified electrician.
- Dispose of waste electrical products responsibly by recycling them. Contact your Local Authority or local store for recycling advice.
Safety Warnings
These instructions are for your safety. Please read through them thoroughly
before use and retain them for future reference. If you are in any doubt about
installing this product, consult a qualified electrician.
This product is only suitable for connection to a 220-240V~ 50Hz supply in
accordance with current IEE wiring regulations, and should be installed in
accordance with local building regulations. It is for domestic ceiling use
only, and is not suitable for a bathroom location.
This fitting is a Class II, Double Insulated product and does not require an
Earth. Live or Neutral must not be connected to Earth.
IMPORTANT: Always switch off the mains supply during installation or
maintenance. We recommend that the fuse is withdrawn or the circuit breaker
switched off at the distribution board whilst work is in progress (turning off
the light switch is not sufficient). Connection should be via a wall switch to
enable safe isolation.
The product must be securely fixed to the mounting surface using the screws
and wall plugs supplied. The screws and wall plugs supplied are suitable for
“masonry” only. Other fixings are not supplied and must be purchased.
Decide on the position of the light fitting or remove existing light fitting.
Note the position of the electrical connections, and ensure there is a solid
mounting surface, Preferably a wooden joist or joist bridge, to support the
weight of the light fitting.
Take care not to drill into any pipes or mains cables beneath the surface
during mounting holes preparation.
Never put anything on the product or hang anything on any part of this
product.
IMPORTANT: Ensure that all electrical connections are tight and that no
loose strands are left out of the terminal.
Never fit bulbs of a higher wattage than those specified on the label (as
these may cause over heating and damage the fitting).
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
local store for recycling advice.
Care and maintenance
For bulb replacement, switch off the product (preferably, isolate it at the
distribution board) and allow it to cool down (Caution: bulb gets hot during
use).
Clean with a dry cloth only.
Do not use liquid or abrasive cleaners on this product.
Troubleshooting
When the bulb does not light after installation:
- Ensure there is no electricity failure.
- Ensure all the connections are secure.
If you have any doubt about installation/use of this product, consult a qualified electrician.
Assembly Instructions
Scan the QR Code
UK Manufactu rer: BH17 7BY
EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>