Shure 588SDX Instrument Condenser Microphone

General Description

Shure Model R180 Replacement Cartridge For Models 588SDX, 515SDX, 515SBGX, 515SBG-18X, 515SBG-18XF, and 515BSLX

This kit contains the following:

• One R180 replacement cartridge
• Two pieces of shrink-wrap tubing (for 515SBGX, 515SBG-8X, 515SBG-8XF, and 515BSLX only)

The following tools are needed to replace the cartridge:

• Long-nose pliers (for 588SDX and 515SDX only)
• A soldering iron of 25 to 40 watts
• Wire cutters (for 515SBGX, 515SBG-18X, 515SBG-18XF, and 515BSLX only)

• 4 (.050 in., 1.3 mm) hex wrench (supplied with 515SBGX, 515SBG-18X, 515SBG-18XF, and 515BSLX only)

Models 588SDX and 515SDX

Wiring Diagram

It is recommended that the following procedure be performed on a table or other flat surface to support the cartridge and case in order to avoid the possibility of breaking the cartridge leads.

To replace the R180 cartridge in the 588SDX and 515SDX, proceed as follows:

1. Unscrew and remove the grille (turning counterclockwise).
2. Gently pull out the old cartridge, being careful not to break the leads.
3. Using a Phillips screwdriver, remove the screws and lock plate which hold the switch in place.
4. Using long-nose pliers, gently pull out the switch, being careful not to break the leads.
5. Unsolder and remove the leads of the old cartridge from the switch.

To prevent damage to the switch, soldering iron between 25 and 40 watts is recommended.

1. Solder the lead closest to the RED dot on the new cartridge (see wiring diagram above) to the terminal with the YELLOW lead on the switch.
2. Solder the other lead from the new cartridge to the terminal with the BLUE lead on the switch.
3. Using long-nose pliers, carefully replace the switch in the case with the blank terminal on the switch facing towards the cartridge (to ensure the UP position is ON), being careful not to pinch the leads.
4. Placing your finger inside the case to support the switch, secure the switch in place by screwing the non-lockplate screw on the side of the switch closest to the grille.
5. Gently insert the new cartridge into the case, being careful not to pinch the leads, and making sure the foam gasket on the cartridge is above the aluminum ring.
6. Replace and screw on the grille.
7. Replace the lockplate on the side of the switch opposite the grille, then secure it with the remaining screw.

Models 515BSLX, 515SBGX, 515SBG-18X, and 515SBG-18XF

It is recommended that the following procedure be performed on a table or other flat surface to support the cartridge and case in order to avoid the possibility of breaking the cartridge leads.

To replace the R180 cartridge in the 515X Series (except the 515SDX), proceed as follows:

1. Slide the supplied shrink-wrap tubing over both leads on the R180 replacement cartridge.
2. Using a #4 (.050 in., 1.3 mm) hex wrench, loosen the setscrew on the base of the grille.
3. Unscrew and remove the grille (turning counterclockwise).
4. Gently pull out the old cartridge, being careful not to break the leads.
5. Using wire cutters, cut the lead from the old cartridge marked by the dot as close to the cartridge as possible, so the lead sticks out from the handle. Mark the cut lead with a small piece of tape.
6. Strip about 1/4-in. (6 mm) of insulation from the end of the lead.
7. Take the lead marked with a red dot on the R180 replacement cartridge and splice it to the taped lead, twisting the stripped ends together.
8. Solder the spliced leads.

To prevent damage to the leads, a soldering iron of 25 to 40 watts is recommended.

1. Slide the shrink-wrap tubing so it entirely covers the soldered connection and bare wires. Gently rub the tip of the soldering iron back and forth along the shrink-wrap tubing until it shrinks.
2. Using wire cutters, cut the other lead of the old cartridge as close to the cartridge as possible, so the lead sticks out from the handle.
3. Strip about 1/4-in. (6 mm) of insulation from the end of the lead.
4. Take the unmarked lead on the R180 replacement cartridge and splice it to the second lead of the handle, twisting the stripped ends together. Solder the leads.
5. Slide the shrink-wrap tubing so it entirely covers the soldered connection and bare wires. Gently rub the tip of the soldering iron back and forth along the shrink-wrap tubing until it shrinks.
6. Gently insert the new cartridge into the case, being careful not to pinch the leads, and making sure the foam gasket on the cartridge is above the aluminum ring.
7. Replace and screw on the grille.
8. Using a #4 (.050 in., 1.3 mm) hex wrench, secure the grille by tightening the setscrew.

Do not torque the setscrew too tightly.

FREQUENTLY ASKED QUESTIONS

What is the Shure 588SDX Instrument Condenser Microphone?

The Shure 588SDX is a high-quality instrument condenser microphone designed for capturing the sound of musical instruments and amplifiers with exceptional clarity and precision.

What types of instruments is the 588SDX microphone suitable for?

The 588SDX is versatile and can be used with a wide range of instruments, including acoustic and electric guitars, drums, brass instruments, and more.

Is the microphone suitable for live performances and studio recording?

Yes, the 588SDX is designed for both live performances and studio recording, making it a versatile choice for musicians and audio professionals.

What is the polar pattern of the 588SDX microphone?

The microphone features a cardioid polar pattern, which is ideal for isolating the sound source and reducing unwanted background noise.

Does the microphone require phantom power?

Yes, the 588SDX requires +48V phantom power to operate. Ensure that your audio interface or mixer provides phantom power.

What is the frequency response range of the 588SDX microphone?

The microphone has a frequency response range of 50Hz-15kHz, which ensures accurate reproduction of instrument sounds.

What accessories are included with the 588SDX microphone?

In the box, you'll typically find the Shure 588SDX microphone, a microphone clip or stand adapter, and a user manual with setup and usage instructions.

Can I use the 588SDX microphone with amplifiers and speaker cabinets?

Yes, the microphone is suitable for miking amplifiers and speaker cabinets, providing excellent sound capture for guitar and bass amplifiers.

Is the 588SDX microphone compatible with wireless systems?

Some models of the 588SDX microphone may offer compatibility with wireless systems when used with the appropriate transmitter and receiver units.

How do I position the microphone for optimal sound capture?

Position the microphone close to the sound source, aiming it at the instrument's sweet spot. Experiment with placement to achieve the desired sound.

Can I use the 588SDX microphone for recording vocals?

While it is primarily designed for instruments, it can be used for recording vocals, but keep in mind that specialized vocal microphones may be more suitable for vocal recordings.

What maintenance is required for the 588SDX microphone?

Regularly clean the microphone grille and ensure proper storage to protect it from dust and moisture. Follow the maintenance guidelines in the user manual.

Is there a warranty for the Shure 588SDX microphone?

Warranty coverage may vary, so be sure to check the warranty details provided by Shure or the retailer at the time of purchase.

Can I purchase replacement parts and accessories for the 588SDX microphone?

Yes, replacement parts and accessories for the 588SDX microphone are available through authorized Shure dealers and the manufacturer's website.

Where can I find additional resources and tips for using the Shure 588SDX microphone?

You can find additional resources, tutorials, and tips on microphone usage on the Shure website and in various online audio and music production communities.

DOWNLOAD THE PDF LINK:Shure 588SDX Instrument Condenser Microphone User Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>