Endon 106710 Lambeth Light Instruction Manual

: June 13, 2024
: ENDON

Table of Contents

Endon 106710 Lambeth Light
Product Information
Product Usage Instructions
Installation and Safety Instructions
Care and maintenance
Troubleshooting
Assembly Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Endon 106710 Lambeth Light

Endon-106710-Lambeth-Light-PRODUCT

Product Information

This product is a pendant light fitting designed for domestic ceiling use. It is suitable for connection to a 220-240V~ 50Hz power supply and should be installed in accordance with local building regulations. The product is classified as Class l and must be Earthed. It is important to note that this pendant light fitting is not suitable for use in a bathroom.

The terminal blocks are supplied according to the requirements of the fitting. It is crucial to ensure that all electrical connections are tight and no loose strands are left out of the terminal. Bulbs of a higher wattage than specified on the label should never be used, as they may cause overheating and damage to the fitting.

When disposing of this product, do not throw it away with household waste. Please recycle it where facilities exist. You can check with your Local Authority or local store for recycling advice.

For maintenance, switch off the product and allow it to cool down before replacing the bulb. Clean the product with a dry cloth only, avoiding the use of liquid or abrasive cleaners.

Product Usage Instructions

Before installation, read through the safety instructions thoroughly.
If you are unsure about installing the pendant light fitting, consult a qualified electrician.
Ensure that the power supply is 220-240V~ 50Hz and meets current IEE wiring regulations.
Select an appropriate location for installation, ensuring it complies with local building regulations.
Make sure the product is suitable for domestic ceiling use and not intended for bathroom installation.
Ensure proper Earth connection for the Class l product.
Do not place anything on the product or hang anything on any part of it.
Check the label for the specified wattage of bulbs to be used and never exceed it.
When replacing bulbs, switch off the product and allow it to cool down before handling.
Clean the product with a dry cloth only, avoiding liquid or abrasive cleaners.
If the bulb does not light after installation, check for electricity failure and ensure all connections are secure. If in doubt, consult a qualified electrician.

Installation and Safety Instructions

Safety Warnings

These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. If you are in any doubt about installing this product, consult a qualified electrician. This product is only suitable for connection to a 220-240V~ 50Hz supply in accordance with current IEE wiring regulations, and should be installed in accordance with local building regulations. It is for domestic ceiling use only, and is not suitable for a bathroom location.

This is a Class l product and must be Earthed. The terminal blocks are supplied according to requirements of the fitting.

IMPORTANT : Always switch off the mains supply during installation or maintenance. We recommend that the fuse is withdrawn or the circuit breaker switched off at the distribution board whilst work is in progress (turning off the light switch is not sufficient). Connection should be via a wall switch to enable safe isolation. The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for “masonry” only. Other fixings are not supplied and must be purchased. Decide on the position of the light fitting or remove existing light fitting.

Note the position of the electrical connections, and ensure there is a solid mounting surface, Preferably a wooden joist or joist bridge, to support the weight of the light fitting. Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation. Never put anything on the product or hang anything on any part of this product.

IMPORTANT :

Ensure that all electrical connections are tight and that no loose strands are left out of the terminal.
Never fit bulbs of a higher wattage than those specified on the label (as these may cause over heating and damage the fitting).
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

Care and maintenance

For bulb replacement, switch off the product (preferably, isolate it at the distribution board) and allow it to cool down (Caution: bulb gets hot during use). Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.