DEXATEK DK9179 Bluetooth Low Energy Module Instruction Manual

June 13, 2024
DEXATEK

DEXATEK - logo

DEXATEK
DK9179
Bluetooth Low Energy
Module Specification

Revision History
This table describes the changes to the specification.

Version Date Description
1.0.0 11/12/2020 Official Release
2.0.0 11/27/2020 Modify Info

Introduction

The DK9179 module is compact, surface mount Bluetooth Low Energy, Bluetooth esh, Thread, Zigbee, 802.15.4 , ANT and 2.4 GHz compliant wireless module. The module is based on Nordic nRF52840 radio Transceiver IC, has a ARM® Cortex®-M4 32-bit processor with FPU, 64 MHz, Flash memory. The outstanding performance at low power consumption and ultra-low cost, the DK9179 module is leading the way for the new generation of Bluetooth low energy modules.

Key Features

  • ARM® Cortex®-M4 32-bit processor with FPU, 64 MHz

  • 2.4GHz multi-protocol transceiver

  • Supported data rates :
    Bluetooth®5: 2 Mbps, 1 Mbps,
    IEEE 801.15.4-2006: 250 kbps

  • 1MB flash, 256kB RAM

  • Flexible power management , DC/DC power mode Wide supply voltage range: LDO (1.8 to 3.3V)

  •  Flexible and configurable 25 GPIO

  •  Peripheral 12-bit/200ksps ADC, Temperature sensor

  •  Up to 4x SPI master/3x SPI slave with EasyDMA

  • Up to 2x I2C compatible 2-wire master/slave

  •  2x UART (CTS/RTS) with EasyDMA

  •  128-bit AES/ECB/CCM/AAR co-processor (on-the-fly packet encryption)

  • Quadrature Decoder (QDEC)

  • Bluetooth mesh and Thread support

Block Diagram

DEXATEK DK9179 Bluetooth Low Energy Module -

Specification

Model DK-9179
Antenna PCB Antenna
Main Chip nRF52840
Application smart home sensors and controllers

industrial loT sensors and contollers
Transmit Power| Transmit Mode output power 0 -÷8 dBm
Wireless Standards| Bluetooth ® 5.0
Data Rates| Bluetooth®5: 2 Mbps, 1 Mbps,
IEEE 802.15.4-2006: 250kbps
Work Mode| Bluetooth ® 5.0
Frequency Range| 2405MHz—2480MHz
Power Consumption
(in different states)| Radio transmitting @ 0 dBm output power, 1 Mbps BLE : 6.4mA
Voltage:| 3.3V
Modulation Technique| GFSK Modulation
Wireless Security| AES/ECB/CCM/AAR Encryption
Dimension(WxDxH)| 25x17x2.3 mm
Certification| BQB
Environment| Operating Temperature: -10°C-45°C
Storage Temperature: -20°C-65°C

Module Pin Definition

DEXATEK DK9179 Bluetooth Low Energy Module - fig2

DK-9179B Module Pin Definition

1| SWDIO| 16| P0.24
2| SWDCLK| 17| P0.05 (ADC)
3| P0.26| 18| P1.09
4| P0.27| 19| P0.25
5| GND| 20| P0.16
6| P0.18| 21| P0.14
7| NC| 22| P0.15
8| P0.13| 23| P1.00 (SWO)
9| VDD| 24| P0.07
10| P0.31 (ADC,LF)| 25| P0.08
11| P0.04 (ADC)| 26| P1.08
12| P0.29 (ADC,LF)| 27| P0.10(NFC2)
13| P0.06| 28| P0.09(NFC1)
14| P0.11| 29| P1.01
15| P0.12| 30| P1.02

Product Dimension

  • PCB SIZE: (W) 25 x (D) 17 mm
  •  PIN OUT: 30
  • Recommended Layout of solder Pad

TOP Layer

DEXATEK DK9179 Bluetooth Low Energy Module - fig3

BOTTON Layer

DEXATEK DK9179 Bluetooth Low Energy Module - fig4

Packaging Info

  • Reel Packaging

DEXATEK DK9179 Bluetooth Low Energy Module - fig5

ITEM DIM ALTERNATE
W 44.001:3°

30

|
E| 1.75 +00..:00|
F| 20.20+°0:::|
So| 40.401:11:|
P| 24.001::|
po| 4.00 “a:|
P2| 2.00 +00:1155|
Do| 01.501;00|
T| 0.40 to:|
Ao| 18.410°|
130| 25.861::::|
Ko| 3.30 +0.10|

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. (Example – use only shielded interface cables when connecting to computer or peripheral devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
If the identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module, Contains FCC ID: SZY-DK9185
Co-location of this module with other transmitters that operate simultaneously are required to be evaluated using the multi-transmitter procedures.
The host integrator must follow the integration instructions provided in this document and ensure that the composite-system end product complies with the requirements by a technical assessment or evaluation to the rules and to KDB Publication 996369.
The host integrator installing this module into their product must ensure that the final composite product complies with the requirements by a technical assessment or evaluation to the rules, including the transmitter operation and should refer to guidance in KDB 996369.
If the identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module, Contains IC: 28614-DK9185
The Separation distance between the device and the user should be more than 20cm. In Canada this device may only be operated indoors.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals