Connect ST100 Wireless Conferencing System User Guide
- June 13, 2024
- CONNECT
Table of Contents
Wireless Conferencing System
Quick Start Guide
ST100 Wireless Conferencing System
Connect is an all-in-one wireless conferencing system designed to
simplify your meetings. With full BYOD support, it allows you to effortlessly
connect your laptop to the speakerphone using a single cable. Enjoy 4K
wireless screen casting, access to conference camera streaming in 1080P, and
the convenience of plug-and-play functionality without the need for software
or drivers.
Connect streamlines your conferencing experience, eliminates cable clutter,
and ensures secure and effcient collaboration.
Package Contents
Overview
ST100
RX100
a Mic Mute
Green light : Mic On
Red light : Mic off
b Speaker Volume Screencast
c Press to start/end screen casting
d Type C cable to laptop
For power supply and signal transmission
e Kensington Nano Slot
f Status Indicator
g USB Interface for camera Language / Pair
h Short press : switch language
Long press : Re-pair
i Power Supply
j HDMI Out for display
Getting Started with Connect
-
Connect the RX100 receiver to the display using the power cable and HDMI cable. If the display does not have a Type-C port to support power more than 5V/2A, use the included switch cable to convert it into two USB-A connectors. One of the USB-A connectors should be USB3.0, which can supply power for the receiver. Alternatively, you can connect the Type-C cable to a power adapter (not included in the package).
-
To connect a USB webcam, plug the camera’s USB cable into the USB-A port on the receiver.
-
Mount the receiver RX100 on the display using the built-in mounting clip. Ensure that the receiver is positioned towards the front side for optimal wireless signal transmission. The optimal wireless transmission range is within 5 meters.
-
Switch the display output source to the connected HDMI port.
-
Connect the speakerphone ST100 to a full-featured Type-C port on your laptop. Wait until the screencasting button light turns green, then press the button to start casting your screen. Press the button again to pause screencasting.
- In the case where the laptop’s type C port does not meet the full feature requirement, use the USB-C to HDMI & USB-A Adapter instead.
USB-C to HDMI & USB-A Adapter * Use the USB 3.0 Extension Cable if the laptop’s USB3.0 port is not nearby the HDMI port.
USB-C to HDMI & USB-A Adapter
- USB 3.0
Extension Cable
- To use the speakerphone ST100 and access the camera wirelessly, in your video conference software, select “Connect” as your microphone, speaker, and camera.
“Connect” option is only available in the camera device list when a camera is connected to the receiver.
Status Indicators
Speaker (ST100)
| Flashing Green | Connecting in progress. |
|---|---|
| Static Green | Connection succeed, read for screencasting. |
| Static Yellow | No DP signal from the laptop port. |
| Static Red | Connection failed: |
1. Replug the speakerphone 5T100
2. The receiver RX100 is not powered, please replug and ensure the RX100
indicator light shows static white.
3. The RX100 and 5T100 are not paired. Please ensure they are the original
paired units. Otherwise please re-pair.
Receiver (RX100)
| Flashing Green | Connection in progress. |
|---|---|
| Static Green | Connection succeed, ready for screen casting. |
| Static White | Stand by. |
Specifications
Microphone
| Built-in Microphone | 8 MEMS Microphone for 360-degree pickup |
|---|---|
| Pick-up Distance | 4 m |
| Signal/Noise Ratio (SNR) Sensitivity | 94dB SPL@1KHz 65dB(A) |
| Acoustic Overload Point | 94dB SPL@1KHz -37±1dB FS |
| Frequency | 132.5dB FS, 10%THD@1KHz |
| Duplex | 20Hz – 8000Hz |
| Beamforming | V |
| Automatic Noise | V |
| Suppression | V |
| Acoustic Echo Cancellation | V |
| Automatic Gain Control | V |
Speaker
| Speaker | 4Ω3W |
|---|---|
| Speaker Size | 50mm |
| Sensitivity | 1KHz 83dB + 3dB @1m @3W |
| Signal/Noise Ratio (SNR) | 50dB |
| Frequency Range | 88dB SPL @1m @3W |
| Max. Sound Pressure Level | 200Hz~20KHz |
| Background Noise | <30dB |
| Total Harmonic Distortion | 200Hz ~ 10KHz MAX 5% |
Wi-Fi
| Authentication protocol | SRRC |
|---|---|
| Wireless Transmission Protocol | Quick UDP Internet Connections |
| Transmission Distance | Up to 10M |
Camera Streaming
| Max. Output Resolution | 1920×1080 @30FPS |
|---|---|
| Support Camera Type | UVC camera |
| Format Supported | H.264 |
Screen Casting
| Max. Screen Output Resolution | 3840×2160 @30FPS |
|---|---|
| Average Latency | 150ms |
Others
I/O Interface| Speakerphone (ST100) : Type C PD + DP ALT
Receiver(RX100) : HDMI x1; TYPE C PD ; USB A 3.0
---|---
Operating System| Win 10/ 11; Mac 10.8 and Later
Product Dimensions| Speakerphone (ST100):
180 x 81 x 32mm / 7.09 x 3.19 x 1.26″ Receiver (RX100):
102 x 45 x 20mm/ 4.02 x 1.77 x 0.79″
Product Weights| Speakerphone (ST100): 385g / 13.58oz
Receiver (RX100): 70g / 2.47oz
Package Contents| Connect: speakerphone(ST100) and receiver(RX100), 2m Type-C
to Type-C cable,
1.5m HDMI Cable,
0.3m USB switch cable
USB-C to HDMI & USB-A Adapter
USB 3.0 Extension Cable
USB Type-C Specification Table
Regulatory and Service Information
The products documented in this guide include aspects which are protected
under their respective patent, copyright, design copyright, registered design
and trademark laws. All other trademarks remain the property of their
respective owners. This guide is distributed online. It may only be
reproduced for use within the institution in which the product is used. For
use outside of your institution, no part of this guide may be reproduced,
transmitted, stored in a retrieval system or translated into any other
language without the prior permission of our company. Please note that the
content in this guide is protected under copyright law. Although every care
has been taken in the compilation of this guide, our company accepts no
responsibility for errors or omissions, or for damages resulting from the use
of information contained within this guide.
Compliance
United States of America
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense. Do not
make any changes or modifications to the equipment.
Europe
We declare under our Sole responsibility that the Connect conforms to the
essential requirements of European Union Directives 2014/53/EU Radio Equipment
Directive (RED), 2014/30/EU Electromagnetic Compatibility Directive,
2014/35/EU Low Voltage Directive and 2011/65/EU Restriction of Hazardous
Substances in Electrical and Electronic Equipment.
Warning
Connect are Class B Products. In a domestic environment, they may cause radio
interference in which case the user may be required to take adequate measures.
United Kingdom
We declare under our sole responsibility that the Connect conforms to the
essential UKCA requirements 2016 No : 1091. Electromagnetic Compatibility
regulations 2016, 2016 No : 1101 Electrical Equipment Safety Regulation 2016,
2017 No : 1206 The Radio Equipment Regulation 2017, and UK SI 2016 No : 1091,
RoHS Restriction of the use of certain Hazardous Substances in Electrical and
Electronic Regulations 2012 – UK SI 2012 No : 3032.
Waste Electrical and Electronic Equipment (WEEE)
For more information concerning the correct disposal of these products, please
contact your reseller.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy. If not installed and used in accordance with the instructions, it may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures :
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and the receiver.
- Connect the equipment to outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
- Any changes or modifications not expressly approved by the party responsible for compliance coud void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>