Endon 104114 Marietta Wall Light Instruction Manual

: June 13, 2024
: ENDON

Table of Contents

Endon 104114 Marietta Wall Light
Product Information
Product Usage Instructions
Safety Warnings
Care And Maintenance
Troubleshooting
Installation Instructions
More Information
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

Endon 104114 Marietta Wall Light

Endon-104114-Marietta-Wall-Light-product

Product Information

The product is a wall light fitting designed for indoor use. Itis suitable for connection to a 220-240V~ 50Hz power supply in accordance with current IEE wiring regulations. The fitting should be installed in accordance with local building regulations.

Important safety warnings include:

The product is not suitable for use in a bathroom location.
Do not put anything on the product or hang anything on any part of it.
Ensure all electrical connections are tight and no loose strands are left out of the terminal.
Never fit bulbs of a higher wattage than specified on the label to avoid over heating and damage to the fitting.
Dispose of waste electrical products through recycling facilities.

The product requires care and maintenance:

Switch off the product and allow it to cool down before replacing the bulb.
Use a dry cloth for cleaning and avoid liquid or abrasive cleaners.

If the bulb does not light after installation, troubleshooting steps include:

Ensure there is no electricity failure.
Ensure all connections are secure.
If in doubt, consult a qualified electrician.

Product Usage Instructions

Before installation, read through the safety instructions provided in the manual.
Consult a qualified electrician if you have any doubts about installing the product.
Ensure the power supply is a 220-240V~ 50Hz source and complies with IEE wiring regulations.
Select a suitable location indoors for mounting the wall light fitting.
Follow local building regulations for installation.
Do not install the product in a bathroom location.
Ensure all electrical connections are tight and no loose strands are left out of the terminal.
Only use bulbs with wattage specified on the label to prevent over heating and damage to the fitting.
Dispose of waste electrical products through recycling facilities.
To replace the bulb, switch off the product and allow it to cool down.
Remove the old bulb and replace it with a new one of the same wattage.
Clean the product using a dry cloth. Do not use liquid or abrasive cleaners.
If the bulb does not light after installation, check for electricity failures and ensure all connections are secure.
If you are unsure about any aspect of installation or usage, consult a qualified electrician.

Safety Warnings

These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. If you are in any doubt about installing this product, consult a qualified electrician. This product is only suitable for connection to a 220-240V~ 50Hz supply in accordance with current IEE wiring regulations, and should be installed in accordance with local building regulations. It is for indoor use only, and is not suitable for a bathroom location.

This is a Class I product and must be Earthed. The terminal blocks are supplied according to requirements of the fitting.

IMPORTANT: Always switch off the mains supply during installation or maintenance. We recommend that the fuse is withdrawn or the circuit breaker switched off at the distribution board whilst work is in progress (turning off the light switch is not sufficient). Connection should be via a wall switch to enable safe isolation.
The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for “masonry” only. Other fixings are not supplied and must be purchased.
Decide on the position of the light fitting or remove existing light fitting. Note the position of the electrical connections, and ensure there is a solid mounting surface, Preferably a wooden joist or joist bridge, to support the weight of the light fitting.
Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.
Never put anything on the product or hang anything on any part of this product.
IMPORTANT: Ensure that all electrical connections are tight and that no loose strands are left out of the terminal.
Never fit bulbs of a higher wattage than those specified on the label (as these may cause over heating and damage the fitting).
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

Care And Maintenance

For bulb replacement, switch off the product (preferably, isolate it at the distribution board) and allow it to cool down (Caution: bulb gets hot during use).
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.