ENDON 106003 Hopton Wall Light User Manual

: June 13, 2024
: ENDON

Table of Contents

ENDON 106003 Hopton Wall Light
Product Information
Product Usage Instructions
Safety Warnings
Care and maintenance
Troubleshooting
Assembly Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ENDON 106003 Hopton Wall Light

ENDON-106003-Hopton-Wall-Light-product

Product Information

The product is a wall light fitting designed for indoor use only. It is suitable for connection to a 220-240V~ 50Hz power supply in accordance with current IEE wiring regulations. The installation should be done in accordance with local building regulations. The product is not suitable for use in a bathroom.

It is important to note that no objects should be placed on the product or hung on any part of it. The product should not be used for any purpose other than its intended use.
The electrical connections should be tight and no loose strands should be left out of the terminal. It is crucial to only fit bulbs of the specified wattage mentioned on the label to prevent overheating and damage to the fitting.
When disposing of the product, it should not be disposed of with household waste. Please check with your Local Authority or local store for recycling advice.
For maintenance, the product should be switched off before replacing bulbs. It is recommended to isolate the product at the distribution board. The bulb may become hot during use, so caution should be exercised while handling. Cleaning should be done with a dry cloth only, and liquid or abrasive cleaners should not be used.
If the bulb does not light up after installation, it is advised to check for electricity failure and ensure all connections are secure. If there are any doubts about installation or usage, it is recommended to consult a qualified electrician.

Product Usage Instructions

Before installing the wall light fitting, read through all safety instructions in the manual.
If you are unsure about installation, consult a qualified electrician.
Ensure that the power supply is 220-240V~ 50Hz in accordance with IEE wiring regulations.
Install the wall light fitting in accordance with local building regulations.
Do not install the product in a bathroom or any other unsuitable location.
Ensure that no objects are placed on the product or hung on any part of it.
Make sure all electrical connections are tight and secure.
Only use bulbs of the wattage specified on the label.
Do not dispose of the product with household waste. Check with your Local Authority or local store for recycling options.
Switch off the product before replacing the bulbs.
Allow the product to cool down before handling hot bulbs.
Clean the product with a dry cloth only. Do not use liquid or abrasive cleaners.
If the bulb does not light up after installation, check for electricity failure and ensure all connections are secure.
If you have any doubts about installation or usage, consult a qualified electrician.

Safety Warnings

These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. If you are in any doubt about installing this product, consult a qualified electrician. This product is only suitable for connection to a 220-240V~ 50Hz supply in accordance with current IEE wiring regulations and should be installed in accordance with local building regulations. It is for indoor use only and is not suitable for a bathroom location. This fitting is a Class II, Double Insulated product and does not require an Earth. Live or Neutral must not be connected to Earth.

IMPORTANT:
Always switch off the mains supply during installation or maintenance. We recommend that the fuse is withdrawn or the circuit breaker switched off at the distribution board whilst work is in progress (turning off the light switch is not sufficient). Connection should be via a wall switch to enable safe isolation.

The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for “masonry” only. Other fixings are not supplied and must be purchased.
Decide on the position of the light fitting or remove the existing light fitting. Note the position of the electrical connections, and ensure there is a solid mounting surface, Preferably a wooden joist or joist bridge, to support the weight of the light fitting.
Take care not to drill into any pipes or main cables beneath the surface during mounting hole preparation.
Never put anything on the product or hang anything on any part of this product.
Ensure that all electrical connections are tight and that no loose strands are left out of the terminal.
Never fit bulbs of a higher wattage than those specified on the label (as these may cause overheating and damage the fitting).
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

Care and maintenance

For bulb replacement, switch off the product (preferably, isolate it at the distribution board) and allow it to cool down (Caution: bulb gets hot during use).
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.