Kuzco Lighting WV346006 Wall Lamp Instruction Manual
- June 13, 2024
- Kuzco Lighting
Table of Contents
Kuzco Lighting WV346006 Wall Lamp
Product Information
- Product Name: WV346006 Wall Lamp
- Technical Support: 1.855.855.8926 / technicalsupport@aloralighting.com.
- Manufacturer: Alora Lighting
- Website: www.aloralighting.com.
- Model Number: WV346006
- Package Contents: Wall Lamp fixture, mounting plate, canopy, canopy screws, junction box screws, wire nuts, glass, driver
Warnings and Cautions
- Please handle the product with care.
- Ensure proper electrical connections to avoid any accidents.
- Read and follow all assembly instructions carefully.
Product Assembly Instructions
- Remove the Wall Lamp fixture from its original package.
- Separate the mounting plate (1c) from the canopy (2a) by removing the canopy screws (2b).
- Attach the mounting plate (1c) to the electrical junction box (1a) using the junction box screws provided (1e) in the hardware package.
- Make proper electrical connections by connecting the black wire to hot L, white wire to neutral N, and ground wire to GND using the wire nuts (1b) provided in the hardware package. Place the driver (4a) in the electrical junction box (1a).
- Attach the canopy (2a) to the mounting plate (1c) using the canopy screws (2b).
- Secure the glass (3a) to the fixture by threading it clockwise.
You are now ready to enjoy your Wall Lamp fixture.
Contact Information
- Phone: 1.855.855.8926
- Address (Canada): 19054 28th Avenue Surrey – BC V3Z 6M3
- Address (USA): 3035 E. Lone Mountain Rd – Las Vegas, NV, 89081
PRECAUTION
WARNINGS AND CAUTIONS
- Make sure POWER is COMPLETELY OFF at the fuse box
- Have your fixture installed by a qualified licensed electrician
- Prepare everything in a clear area
- Wear gloves at all times during this installation
- Read instructions carefully before you start assembly
- Keep this installation sheet for future reference
Please Note:
- This Alora LED fixture comes with pre-wired LED module(s)
- Unless instructed, Do Not touch any part of the LED module(s) as any unnecessary contact with the module could cause permanent damage
- For dimming, an ELV (Electronic Low Voltage) or TRIAC type of dimmer is required
- 120V input
NOTICE
- The important safeguards and instructions outlined in this sheet cannot cover all possible conditions and situations that may occur. It must be understood that caution and certain care factors must be followed. These instructions are provided for your safety and we highly recommend that a licensed, trained electrician install this unit.
- This fixture is designed to be mounted on a correctly installed standard round or octagon box OR through a wiring box with a plaster frame. The box must be securely mounted to the structure of the building. The crossbar and hardware supplied should be used, directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.
ASSEMBLY INSTRUCTIONS
-
Step 1
Remove fixture from its original package. -
Step 2
Separate mounting plate (1c) from canopy (2a) by removing canopy screws (2b). -
Step 3
Attach mounting plate (1c) to electrical junction box (1a) using junction box screws provided (1e) in hardware package. -
Step 4
Make proper electrical connections (black to hot “L”, white to neutral “N”, ground to “GND”) with wire nuts (1b) provided in hardware package and place driver (4a) in electrical junction box (1a). -
Step 5
Attach canopy (2a) to mounting plate (1c) with canopy screws (2b). -
Step 6
Secure glass (3a) to fixture by threading clockwise. You are now ready to enjoy your fixture.
-
P: 1.855.855.8926
-
CANADA: 19054 28th Avenue Surrey – BC V3Z 6M3
-
CANADA: w 3035 Lone Mountain Rd – Las Vegas, NV, 89081 www.aloralighting.com.
-
20230619 ww.aloralighting.com.
TECHNICAL SUPPORT
- 1.855.855.8926
- technicalsupport@aloralighting.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>