Emax 2.4G Nano Aeris Link Micro Express LRS User Guide
- June 13, 2024
- Emax
Table of Contents
Aeris Link Micro
ExpressLRS 2.4G/915M
www.emaxmodel.com
www.emax-usa.com
Thanks for purchasing Aeris Link ExpressLRS 2.4G/915M，
Please follow the instruction manual to assemble and configure your product.
Disclaimer
Before using this product, users are advised to carefully read this
disclaimer. By using this product, it is deemed that the user fully
acknowledges and accepts all the contents of this disclaimer. Individuals
under the age of 18 are not suitable to use this product.
The Aeris Link Micro ExpressLRS 2.4G/915M high-frequency module is a new
generation remote control wireless system developed based on the open-source
project ExpressLRS. The ExpressLRS system features long-range remote control,
stable connection, low latency, high refresh rate, and flexible configuration.
When using this product, please carefully read the user manual and follow the
instructions. Ensure that the power supply system is in good condition and
the operations are correct. In the event of personal injury, property damage
(direct or indirect), our company will not assume any civil or legal
liability.
Safety Precautions
- Please assemble and operate this product correctly following the instructions provided.
- Avoid dropping or impacting the product to prevent malfunctions.
- Do not block the ventilation openings to prevent overheating.
- If you experience any discomfort during use, stop using the product immediately and resume use only with the permission of a doctor.
- Do not use this product while under the influence of alcohol, drugs, medication that causes drowsiness, or in a weakened or mentally impaired state.
- Do not disassemble, modify, or use other parts and accessories beyond the recommended configurations.
- Avoid using a damaged high-frequency module to prevent short circuits or fires.
- Do not immerse the product in water.
- Do not use this product in harsh environmental conditions such as strong winds, rainy days, lightning, or snow.
- Avoid using this product in environments with strong electromagnetic interference.
Description
- 915M-T Type Antenna
- 2.4G-T Type Antenna
- Antenna Interfaces : 915M Version: SMA-KY external thread with female connector 2.4G Version: RP-SMA-KY external thread with male connector
- RGB LED Lights / Fan Ventilation / Heat Dissipation Port
- Ventilation Port
- Power (XT30) Interface
- Type-C Interface
- NC
- CRSF
- GND
- 5-21V
- Reset button
- Flash button
Operation Instructions
- Using the OpenTX remote control system as an example, start by selecting “MODEL” from the main menu.
- Once in the “MODEL” menu, navigate to the “TOOLS” interface.
- Within the “TOOLS” interface, locate and select “ExpressLRS” to enter the information screen related to ExpressLRS configuration.
| Weight | Parameter | Illustrate |
|---|---|---|
| 1.Packet Rate： | 50hz (Purple light) |
100hz FULL (Purple light)
150hz (Deep blue light)
250hz (Light blue light)
333hz FULL (Light blue light)
500hz (Blue-green light)
D250hz (Green light)
D500hz (Yellow-green light)
F500hz (Orange light)
F1000hz (Orange light)| 2.4G Version: The refresh rate can be adjusted to
change the color of the LED lights and fan. The default setting is 250hz
(blue light). (It is recommended to use firmware version 2.7.1 or higher to
run the F1000Hz mode.)
25hz (Purple light)
50hz (Blue light)
100hz (Blue-green light)
100hz Full (Yellow-green light)
200hz (Red light)| 915M Version: The refresh rate can be adjusted to change
the color of the LED lights and fan. The default setting is 50hz (blue
light).
2.Telem Ratio：| Std OFF 1：128 1：64 1：32
1：16 1：8 1：4 1：2 Race| Default setting is “Std” (1:128)
3.Switch Mode：| Wide Hybrid| 2.4G Version, default setting is “Wide.
8ch 16ch Rate 12ch Mixed| 915M Version：Default Wide
4.Model Match：| OFF(ID:0) On (ID:0)| Default OFF(ID:0)
5.TX Power
Max Power：| 10mW 25mW 50mW 100mW 250mW 500mW 1000mW| 2.4G Version: the maximum
power is 1W, and it can be adjusted based on actual needs. The default power
setting is 10mW.
| 10mW 25mW 50mW 100mW 250mW 500mW 1000mW 2000mW| For the 915M Version: the
maximum power is 2W, and it can be adjusted based on actual needs. The
default power setting is 10mW.
Dynamic：| OFF Dyn AUX9 AUX10 AUX11 AUX12| Default OFF
Fan Thresh：| 10mW 25mW 50mW 100mW 250mW 500mW 1000mW 2000mW Never| The fan
starts corresponding to the power switch and can be adjusted according to
actual needs. The fan starts by default at 10mW.
6.VIX Administrator
Band：| OFF A B E F R L| Default OFF
Channel：| 1 2 3 4 5 6 7 8| Default 1
Pwr Lvl ：| （ – 1 2 3 4 5 6 7 8 ）| Default –
Pitmode：| OFF On AUX1↑ AUX1↓ AUX2↑ AUX2↓ AUX3↑ AUX3↓ AUX4↑ AUX4↓ AUX5↑ AUX5↓
AUX6↑ AUX6↓ AUX7↑ AUX7↓ AUX8↑ AUX8↓ AUX9↑ AUX9↓ AUX10↑ AUX10↓| DefaultOFF
Send VTx
7.WiFi Connectivity| | The high-frequency module has enabled WiFi
functionality for firmware updates. : http://10.0.0.1
Enable WiFi| | P/#expresslrs
Enable Rx WiFi|
Enable Backpack WiFi|
Enable VRx WiFi
8.Backpack| |
DVR Rec:| OFF AUX1↑ AUX1↓ AUX2↑ AUX2↓ AUX3↑ AUX3↓ AUX4↑ AUX4 ↓ AUX5↑ AUX5↓
AUX6↑ AUX6 ↓ AUX7↑ AUX7↓ AUX8↑ AUX8 ↓ AUX9↑ AUX9↓ AUX10↑ AUX10↓| Default OFF
DVR Srt Dly:| 0s 5s 15s 30s 45s 1min 2min| 0s
DVR Stp Dly:| 0s 5s 15s 30s 45s 1min 2min| 0s
10.Bind| The high-frequency module enters the binding state. Note: When
the highfrequency module enters the binding state, there will be no light
flashing or other visual indications. After 5 seconds, the module will
automatically exit the binding state. Note: If you have updated the firmware
of the high-frequency module and configured a binding password (Binding
Phrase), you won’t be able to enter the binding state using the previous
method. In this case, please set the receiver with the same binding password,
and module and receiver will automatically establish a binding connection.
Version| V3.0|
Warning:
- Before powering on this product, please ensure that the matching antenna is properly installed. Failure to do so may result in damage to the chip!
- When operating this product at high power output, please use an external power source. Failure to do so may lead to insufficient power supply for the remote control!
Product Specifications:
| Weight | Approximately 39g (exduding antenna) |
|---|---|
| Dimensions | 72 x 32 x 32mm (excluding antenna) |
| Operating Frequency | 2.4G Version: 2.4GHZ ISM. |
915M/868M Version: 915MHz FCC/868MHz EU
Output Power| 10mW (default)
2.4G Version: Supports adjustable power levels of
25mW/50mW/100mW/250mW/500mW/1000mW.
915M Version: Supports adjustable power levels of
25mW/50mW/100mW/250mW/500mW/1000mW/2000mW
Refresh Rate| 2.4G Version: 50hz, 100hz FULL, 150hz, 250hz, 333hz FULL, 500hz,
D250hz, D500hz, F500hz, F1000hz.
915M Version: 25hz, 50hz, 100hz, 100hz Full, 200hz
Antenna| 2.4G Version: Comes with a built-in gain T-shaped antenna, and can
also use other antennas with RP-SMA-J internal thread and female connector.
915M Version: Comes with a built-in gain T-shaped antenna, and can also use
other antennas with SMA-J internal thread and male connector.
Configuration| Supports Crossfire serial data protocol (CRSF) signal and uses
LUA scripts to control the high-frequency module. Compatible with OpenTX
remote controllers.
Interface| Type-C interface.
External Power| XT30 interface (supports voltage input of 5-21V, recommended
to use 2S (8.4V))
Product List:
2.4G Version:
Eris Link Micro ExpressLRS 2.4G (Complete set)………………………..X1
2.4G-T Type Antenna……………………………………………………………………..X1
Product Introduction Manual/Website Card……………………………….X1
915M Version:
Eris Link Micro ExpressLRS 915M (Complete set) ……………………..X1
915M-T Type Antenna…………………………………………………………………..X1
Product Introduction Manual/Website Card……………………………….X1
Regarding the disposal of the product:
This product (plastic casing with printed circuit board inside) should be
disposed of following the local residential waste disposal regulations. Please
adhere to the guidelines provided by your local authorities for proper waste
disposal. Avoid disposing of electronic products with regular household
waste, as they may contain hazardous materials that can harm the environment
if not handled correctly. Instead, look for designated electronic waste
recycling facilities or collection points in your area to ensure responsible
and environmentally friendly disposal.
Thanks for choosing EMAX products！
Reminder:
- Avoid prolonged usage to prevent discomfort. If you experience any discomfort while using the product, stop using it immediately, and continue only after getting approval from a doctor. This product is not suitable for individuals under the age of 18.
- Before powering on the product, ensure that the matching antenna is properly installed to avoid damaging the chip.
- When operating the product at high power output, use an external power source to prevent inadequate power supply to the remote controller.
- When changing the power, please follow the relevant local laws and regulations!
www.emaxmodel.com
www.emax-usa.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>