SoundCore Motion X600 Portable Speaker A3130 User Manual

SoundCore Motion X600 Portable Speaker A3130

USER MANUAL

At a Glance

1. Power
2. Bluetooth
3. Spatial Sound
4. BassUp
5. Volume Down
6. Play / Pause
7. Volume Up
8. USB-C Charging Input
9. AUX IN

Charging

Use a certified USB-C cable and charger to prevent any damage.

Fully charge this speaker before the first use to prolong the lifespan of the built-in battery

Powering On / Off

This speaker will power off automatically after 20 minutes if no device is connected.

Using Your Speaker

Bluetooth Mode

With this speaker, you can enjoy music through your Bluetooth-enabled devices.

• To re-enter Bluetooth pairing mode, press the Bluetooth button once.
• This speaker can only play music on one mobile device at a time. To play from another connected device, pause the device that’s currently active first.
• Each time you power on your speaker, it will automatically connect to your last connected device if available within the Bluetooth range. If not, press the Bluetooth button to enter Bluetooth pairing mode.

TWS (True Wireless Stereo) Mode

Two identical Motion X600 speakers can pair with each other for stereo sound.
Both speakers can play the same audio (one as the left channel and the other as the right channel).

1. Connect either speaker with your Bluetooth device.
2. On both speakers, press and hold the Bluetooth button for at least 2 seconds to enter TWS pairing mode.

To exit TWS mode, press and hold the Bluetooth button for at least 2 seconds.

Spatial Sound

Spatial sound places sound all around you to create an immersive listening experience.

LDAC

Use devices powered by Android 8.0 or later to experience LDAC quality sound.

1. Open the soundcore app.
2. Go to the Settings icon on the home page.
3. Click on “Sound Mode.”
4. Select “Preferred audio quality” to switch to LDAC codec.

• It takes about 10 seconds to switch audio codecs. You may be requested to update the speaker’s firmware if available.
• LDAC provides higher quality sound, increases power consumption, and reduces playtime.
• Enable LDAC in a low-interference environment to ensure a stable Bluetooth connection.

AUX Mode

Insert a 3.5mm AUX cable (not included) to play audio on an external device.

When using AUX mode, control audio playback via the connected device.

Button Controls

Reset

Press and hold the Bluetooth button and volume up button simultaneously for at least 4 seconds to reset the speaker.

App

Download the soundcore app to enhance your experience

Product information: Check the product name and software version, or read the user manual.
Firmware update: You will be informed once a new version of firmware is detected when you connect the speaker with the app.
Battery status: Indicates the remaining battery level of your speaker.
Volume control: Adjust the volume level via the app without pressing the buttons on the speaker.
EQ settings: There are 6 EQ settings you can choose from in the app to optimize your experience while enjoying different music genres.

• Soundcore Signature: Standard EQ mode optimized for well-balanced sound.
• Voice: Voices stand out more clearly from other ambient sounds.
• Treble Boost: High frequencies are enhanced.
• Balance: No enhancement for high-frequency and low-frequency sounds.
•  Custom: Customize the EQ setting to suit you in the app.
•  BassUp: Turn on BassUp to enhance the low-frequency sound.

Set auto-power off time: Set an auto-power off time (5 / 10 / 20 / 60 minutes, 20 minutes by default). The speaker will automatically power off when the time is up.

Voice prompt: Mute or restore the voice prompt while powering on / off.

Specifications

Specifications are subject to change without notice.

Support Videos

How to Enable True Wireless Stereo

How to Connect Using LDAC

Soundcore Motion X600 A3130 FAQ

What’s in the box?

• Motion X600 Speaker
• 60 cm USB-C to C Cable
• Safety Card
• Quick Start Guide

Note: Aux cable and wall charger are not included!

**Does the soundcore app work with the new Motion X600? Why I cannot

find the Motion X600 listed in soundcore App?**

Yes, please reinstall soundcore app and test it again. Please know that you can download the soundcore App from the Google Play store or Apple Store.

How long does it take to charge Motion X600?

It takes around 6 hours to charge with a certified 5V/3A wall charger.

How do I reset Motion X600?

Turn on the speaker, then hold the Bluetooth button and volume up button simultaneously for 5-10 seconds to reset the speaker.

Is Motion X600 waterproof?

Motion X600 supports IPX7 waterproofing, but before submerging it in water, it is necessary to ensure that the waterproof cover on the back is securely fastened.

Why is the power button recessed?

The recessed design make it easy to use the button in low-light and dark environments.

Does Motion X600 have a built-in microphone?

Yes.

How do I turn off Motion X600’s voice prompts?

1. Connect your device to Motion X600.

2. Download and open the soundcore app.

3. Press the top right corner to access more options.

4. Turn off voice prompts.

How do I update Motion X600’s firmware?

1. Download the soundcore app.

2. Pair Motion X600 with the soundcore app, then press Update Firmware.

3. Do not use your phone while the firmware is updating, except if you’ve set the soundcore app to run in the background.

4. Motion X600 will restart automatically after updating successfully.

What is spatial audio and how do I turn it on?

Spatial audio places sound all around you to create an immersive listening experience. Simply press the Spatial Audio button to turn on.

Does spatial audio require a specific music format?

No.

Which Bluetooth decodings does X600 support?

soundcore Motion X600 supports LDAC and SBC.

Can Motion X600 be used plugged in without relying on the battery?

The power supply won’t bypass the battery. It operates in charge-and-play mode when connected to power.

**Can Motion X600 pair with other speakers, such as the Motion+

speaker?**

No, however, Motion X600 can pair with up to another Motion X600 speakers via TWS.

Does Motion X600 come with a carry case?

No.

Can the custom EQ of Motion X600 be saved?

Yes.

Does a single Motion X600 speaker support stereo sound?

Yes.

Can the battery of Motion X600 be replaced?

No.

**Can I disable Bluetooth searching on Motion X600 when it is powered

on?**

No.

Does Motion X600 have a microphone?

Yes, Motion X600 has a built-in microphone located at the top right corner of the speaker.

Does Motion X600 support USB playback?

No.

What is LDAC?

LDAC is a Bluetooth encoding format that can transmit 3 times the amount of data of ordinary Bluetooth SBC.

Note: LDAC only works on devices running Android 8.0 or above, it doesn’t works on iPhone devices.

How do I use LDAC?

On a device powered by Android 8.0 or above, do the following:

1. Open the soundcore app.

2. Go to the Settings

3. Click on Sound Mode

4. Select Preferred Audio Quality and switch to LDAC codec.

Notes:

• It takes about 10 seconds to switch audio codecs. You may be required to update the speaker’s firmware if available. Do not use the app or speaker while updating.
• LDAC provides higher quality sound but increases power consumption and reduces playtime.
• Enable LDAC in a low-interference environment to ensure a stable Bluetooth connection.

Why do some devices experience interrupted sound when using the LDAC

function?

After enabling LDAC, your device will default to adaptive bit rate mode. Generally, there won’t be any sound interruptions, however, if Android users turn on developer mode and select LDAC 990 kbps playback, sound may slightly cut in and out.

If you would like to select 990 kbps LDAC, we recommend following these steps:

1. Turn off Wi-Fi on your Android device.

2. Turn off any extra Bluetooth and Wi-Fi devices in the room.

3. Connect your Android device to Motion X600 via Bluetooth and switch to 990 kbps.

4. Keep the distance between the Android device and Motion X600 within 0.5 m (1.6 ft).

5. Play local music files.

How do I use the EQ?

Open the soundcore app and go to Equalizer > Custom > Full-Band. Then click any dot to expand the corresponding frequency band, long press the dot and drag to customize the frequency.

How can I TWS pair two Motion X600 speakers at the same time?

Method 1:

1. Speaker 1 and Speaker 2: Long press the power button to start both speakers.

2. Speaker 1: Hold the Bluetooth button until the button light flashes white.

3. Speaker 2: Hold the Bluetooth button until the button light flashes white.

4. Wait for a few seconds, and you will hear a sound when the two speakers have paired successfully.

5. The master speaker is the one with the blue light.

6. Use the master speaker to pair with your device.

Method 2:

1. Long press the power button to start both speakers

2. Connect either speaker with your Bluetooth device.

3. On both speakers, press and hold the Bluetooth button for at least 2seconds to enter TWS pairing mode.

4. Wait for a few seconds, and you will hear a sound when the two speakers have paired successfully.

Note: To exit TWS mode, hold the Bluetooth button for at least 2 seconds.

How does stereo sound work during TWS pairing?

When you have two Motion X600 speakers paired at the same time, the master speaker supports the left channel and sky channel(if the spatial audio is turned on), while the secondary speaker supports the right channel and sky channel(if the spatial audio is turned on).

Can I get stereo sound when using one Motion X600?

Yes, you can also get the stereo sound with a single Motion X600 speaker. The left side plays left channel, the right side plays the right channel.

Why is the battery life less than 12 hours?

12-hour battery life is based on measurements taken at 1/4 power and with Bass Mode off. The actual battery life may vary depending on factors such as the type of content being played, custom EQ settings, and volume level.

Can I increase the bass on my Motion X600?

You can download the soundcore app and pair the speaker with soundcore app to enhance the bass via the EQ.

The audio source quality might also affect the performance of the bass. Try using high-quality audio files or streaming services.

I can’t detect Motion X600 via Bluetooth. What should I do?

1. Fully charge the speaker.

2.Turn on the speaker, then hold the Bluetooth button and volume up button simultaneously for 5-10 seconds to reset the speaker.

3. Turn your device and your device’s Bluetooth off and on.

4. Clear all pairing records on your device.

5. Restart your speaker and reconnect to it.

6. Try the speaker with different devices if possible.

How can I share a custom EQ？

1. Download the soundcore app.

2. Pair Motion X600 with the soundcore app.

3. Click Equalizer.

4. Click the share button in the upper right corner, then click Copy Link or QR Code. You can choose an app to share the link or the QR Code with your friends.

Note: To use the sharing function, you need to log in to your soundcore account first.

How do I import a custom EQ that someone has shared with me?

Method 1: Copy the Link (Note: The link must be the EQ link of Motion X600 generated in the soundcore App)

Open the soundcore app and pair with Motion X600, then copy the EQ link, the link will automatically be detected and you will be asked whether or not your want to import it.

Click “Yes” and then click “Import”.

Method 2: Scan the QR Code

Open the soundcore app and pair with Motion X600.

Go to Equalizer > Add > Scan Code for EQ. Then scan the QR code your friend shared with you and click “Import”.

DOWNLOAD

SoundCore Motion X600 Portable Speaker A3130 User Manual – [Download PDF]

SoundCore Motion X600 Portable Speaker A3130 QSG – [Download PDF]

A3130 Soundcore Motion X600 Declaration of Conformity – [Download PDF]

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>