Nikon 10×42 LaserForce Rangefinder Binocular Instruction Manual

RANGEFINDER BINOCULARS
LaserForce

10×42
Instruction manual

Introduction

Thank you for purchasing the Nikon Rangefinder Binoculars LaserForce.
Before using this product, read and understand the contents of this manual thoroughly for correct use. After reading, keep this manual handy for easy reference.
About the manual

• No part of the manual may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form, by any means, without Nikon’s prior written permission.
• Nikon will not be held liable for any errors this manual may contain.
• The appearance, specifications, and capabilities of this product are subject to change without notice.

About controls for radio interference

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and to the EU EMC directive. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

About measurement results
This device is a basic rangefinder. Its measurement results cannot be used as official evidence.

SAFETY AND OPERATION PRECAUTIONS

Strictly observe the guidelines contained in this manual in order to use this product safely and prevent possible injury or property damage to you and others. Understand the contents thoroughly for correct use of the product.

**WARNING
This indicates that improper use by ignoring the contents described herein can result in potential death or serious injury.
CAUTION
This indicates that improper use by ignoring the contents described herein can result in potential injury or material loss.
SAFETY PRECAUTIONS (Laser)**
This product uses an invisible laser beam. Be sure to observe the following:

WARNING

• Do not press the PWR button while looking into the laser emission aperture. You may damage your eyes.
• Do not aim at the eyes.
• Do not point the laser at people.
• Do not look at lasers with other optical instruments such as lenses or binoculars. You may damage your eyes.
• When not measuring, keep your fingers away from the PWR button to avoid accidentally emitting the laser.
• When not in use for an extended period, remove the battery.
• Do not disassemble, remodel, or repair the product. The laser emission may be harmful to your health. If the product is disassembled, remodeled, or repaired, it is no longer guaranteed by the manufacturer. Refer to a Nikon authorized service representative for repairs.
• If the product’s body is damaged or if it emits a strange sound because it was dropped or some other cause, stop using it immediately and remove the battery. Store the product in a place out of reach of children.

SAFETY PRECAUTIONS (Binoculars)
This product employs binoculars in its optical system to aim at a target. Be sure to observe the following:
WARNING
Never look directly at the sun while using this product.
Looking directly at the sun, intense light, or lasers may seriously damage the eyes or cause blindness.

**CAUTION**

• Keep the plastic bag used to wrap this product out of reach of children. The bag may block their mouths and noses and cause them to suffocate.
• Your fingers may get pinched when you adjust the interpupillary distance or diopter. Be particularly careful when letting small children use the product.
• Keep children from inadvertently swallowing the cap, eyecup, etc. In such a case, consult a doctor immediately.
• When not using this product, do not turn it on.
• When carrying this product, store it in the case.
• If this product fails to operate correctly for any reason, discontinue use immediately and consult with a Nikon authorized service representative.
• Do not leave this product in an unstable place. It may fall and cause injury.
• Do not use this product while walking. You may walk into unexpected objects or fall and get hurt.
• Do not swing this product by the strap. You may hit others and cause injury. The rubber parts of this product (such as the eyecups) or included case and strap may deteriorate if used or stored for a long period of time. The deteriorated rubber may attach on clothes and cause stains. Check their condition before use, and consult with a Nikon authorized service representative if a defect is found.
• Using the eyecups for extended periods of time may cause skin inflammation. If you develop any symptoms, stop using and consult a doctor immediately.

PRECAUTIONS (Lithium battery)
Incorrect use may cause the lithium battery to rupture or leak, which will corrode the device or stain your hands and clothing.
Be sure to observe the following:

• Install the battery with the + and – poles positioned correctly.
• Remove the battery when this is depleted or will not be used for extended periods.
• Keep the battery away from fire or water. Never disassemble the battery.
• Do not charge the lithium battery.
• Do not short the terminal of the battery chamber.
• Do not carry the battery together with keys or coins in a pocket or bag. You may short the battery and cause overheating.
• If liquid leaks from the lithium battery come into contact with clothing or skin, rinse with plenty of water. If it enters the eyes or mouth, rinse with water and consult a doctor immediately.
• When disposing of lithium batteries, follow your local area regulations.

OPERATION PRECAUTIONS

HANDLING & CONTROLS

• Do not open the body beyond the limit. Also, do not rotate the rotating parts of the adjustment rings beyond their limits.
• Do not subject this product to physical shock.
• If you accidentally apply strong physical shock or drop the product and suspect a malfunction, consult with your local dealer or a Nikon-authorized service representative immediately.
• Do not use the product underwater.
• Wipe off any rain, water, sand, or mud on the product as soon as possible with a soft, clean cloth.
• When this product is exposed to extreme temperature changes (suddenly brought from a cold place to a warm place or vice-versa), the lens surfaces may get cloudy. Do not use the product until the cloudiness has disappeared.
• Do not leave the product in direct sunlight. Ultraviolet rays and excessive heat may negatively affect.

CARE & MAINTENANCE

LENS

• When removing dust on the lens surface, use a soft oil-free brush.
• When removing stains or smudges like fingerprints from the lens surface, wipe the lens gently with a soft, clean cloth. Use a small quantity of pure alcohol (ethanol) or commercially-available lens cleaner and wipe from the center of the lens to the outside in a circular motion. Do not use hard materials because they may scratch the lens surface.

MAIN BODY
Remove dust trapped in the rotating parts of the adjustment rings, etc. with a soft brush.
After gently removing dust with a blower*, clean the body surface with a soft, clean cloth.
After use at a seaside, wipe off the salt that may be on the body surface with a damp, soft, clean cloth, and then wipe with a dry cloth. Do not use benzene, thinner, or other cleaners containing organic solvents.

• A rubber cleaning tool that blows air from a nozzle.

STORAGE

• Water condensation or mold may occur on lens surfaces because of high humidity. Therefore, store the product in a cool, dry place. After use on a rainy day or at night, thoroughly dry it at room temperature, then store in a cool, dry place.
• For long-term storage, keep this product in a plastic bag or an airtight container with a desiccant. If this is not possible, store in a clean, well-ventilated place, separate from the case because it is easily affected by moisture.
• Do not leave the product in a car on a hot or sunny day, or near heat-generating equipment.

The symbol for separate collection applicable in European countries
This symbol indicates that this battery is to be collected separately.
The following applies only to users in European countries.

• This battery is designated for separate collection at an appropriate collection point. Do not dispose of as household waste.
• For more information, contact the retailer or the local authorities in charge of waste management.

The symbol for separate collection applicable in European countries
**** This symbol indicates that this product is to be collected separately.
The following applies only to users in European countries.

• This product is designated for separate collection at an appropriate collection point. Do not dispose of as household waste.
• For more information, contact the retailer or the local authorities in charge of waste management.

Key features

• Rangefinder Binoculars measuring from 9 to 1,730 m/10 to 1,900 yd.*

• Horizontal Distance display mode and Actual Distance display mode is selectable

• Single or continuous measurement (up to 8 seconds)

• Red OLED display with 4-step intensity adjustment

• Automatic Power shut-off (approx. 8 seconds unoperated from standby screen)

• Restart from settings used last time

• Extra-low dispersion (ED) glass for chromatic aberration compensation and clearer viewing

• All lenses and prisms are multilayer-coated for bright images

• Long eye relief design

• Turn-and-slide rubber eyecups with multi-click

• Waterproof /fog proof performance with a nitrogen-filled body that prevents fogging or molding inside the optical system even under significant changes in temperature.

• Reference value. Under Nikon’s measurement conditions.

This product uses an invisible laser beam for measuring. It measures the time the laser beam takes to travel from the rangefinder to the target and back. Laser reflectivity and measurement results may vary according to climatic and environmental conditions, as well as the color, surface finish, size, shape, and other characteristics of the target.
Measurement may be inaccurate or fail in the following cases:

• In snow, rain or fog
• Small or slender target
• Black or dark target
• Target has stepped surface
• Moving or vibrating target
• When measuring the surface of the water
• Target measured through glass
• When the target is glass or a mirror
• When laser incidence to the target’s reflective surface is oblique

Nomenclature

1 Eyepiece lens
2 Interpupillary distance
3 Eyecup
4 Neck strap eyelet
5 Focusing ring
6 PWR button (power on/measurement button)
7 MODE button
8 Objective lens/invisible laser emission aperture| 9 Central shaft
10 Objective lens/invisible laser receiving aperture
11 Diopter adjustment index
12 Diopter adjustment ring
13 Internal display diopter adjustment ring
14 0 (zero) diopter position
15 Battery chamber cover
16 Product number label
17 Indication
---|---

NIKON VISION CO., LTD. IEC60825-1
CLASS 1M LASER PRODUCT. DO NOT EXPOSE USERS OF TELESCOPIC OPTICS.
FDA CLASS I LASER PRODUCT. COMPLIES WITH 21CFR 1040.10 AND .11.

Internal display

1 Battery condition
2 Laser irradiation mark: Displayed when the laser is being emitted. Do
not look into the product from the objective lens side while this is displayed.
3 Horizontal distance mode
4 Target mark
5 Units of measure (M: meter/Y: yard)
6 Distance

• The internal display of this product is enlarged by the eyepieces. Although you may see dust that has entered, it does not effect the accuracy of measurement.

Preparation

Type of battery
3V CR2 lithium battery x1
Inserting/replacing the battery

1. Open the battery chamber cover.
   Rotate the battery chamber cover counterclockwise with an object such as a coin to open it.

2. Insert the battery.
   To replace the battery, take out the old battery before inserting a new one.
   Follow the battery insertion mark inside the battery chamber to insert the + and – ends of the battery in the correct orientation (insert so that the – end faces up).

3. Attach the battery chamber cover.
   Rotate the battery chamber cover clockwise with an object such as a coin and secure it firmly.
   When attaching the battery chamber cover, securely screw it all the way and check that it is secured.

• The battery chamber cover may be difficult to rotate because this product uses a rubber seal to maintain its waterproof capabilities.

Battery condition

available.
| After powering on, displays for 2 seconds only.| Power getting low.
Prepare to replace the battery.
| Displayed normally| Low. The battery should be replaced with a new one.
Blinks
After blinking 3 times, automatically powers off.| The battery is empty. Replace the battery.

Battery life
Approx. 4,000 times (at approx. 20°C/68°F) Use this number of measurements as a reference because it changes depending on the environment such as temperature and other factors.

• The battery supplied with this product is for operation checking. Due to natural electrical discharge, the life of this battery will likely be shorter than that noted above.
• If water enters the battery chamber due to submersion, dry the battery chamber well, then replace the battery.

Adjusting the eyecups

• For eyeglass wearers, use fully retracted. If your view is secured, you can also use the two intermediate click stops.
• For non-eyeglass wearers, use fully extended. If your view is secured, you can also use the two intermediate click stops.
• For directions in which to turn the eyecups, please refer to the image on page 11.

Adjusting interpupillary distance
While looking at a subject through the eyepieces, gently rotate the product body until the two images of the subject become one as in (A).

• Take care not to get your fingers pinched when adjusting the interpupillary distance.

Adjusting the focus of the internal display and diopter difference

1. Press the PWR button to turn on the power.
   The internal display is displayed.

2. Look in only with your right eye, rotate the internal display diopter adjustment ring, and adjust the focus of the internal display.

3. Designate a target.
   You can correctly focus by adjusting each eye with respect to the same target.

4. Look in only with your right eye, rotate the focusing ring, and adjust the focus of your right eye.

5. Look in only with your left eye, rotate the diopter adjustment ring, and adjust the focus of your left eye.
   Correct the difference (diopter difference) in vision between the left and right.

6. Look in with both eyes and check if the focus is correct.

7. When you view a different subject, adjust the focusing ring until you obtain a sharp image.

Mode settings

You can change the settings of each mode. The details of each mode and the settings at the time of purchase (factory default settings) are explained below. If you do not need to change the settings, proceed to “Measurement” (page 20).

distance ( )

Changing the settings

1. Turn on the power.
2. Press and hold the MODE button to be able to change the settings.
3. Perform the operations below to switch the mode or settings.
   • Pressing the MODE button: Switches the mode.
   • Pressing the PWR button: Switches the setting of the displayed mode.

• If you press and hold the MODE button or if you do not operate the button for about 8 seconds, the product returns to standby.

• Operating the MODE button
  There are two ways to press the MODE button. Operate the button while following the descriptions in this manual.

  • “Press and hold” means to continue pressing the button for 1.5 seconds or longer.
  • “Press” means to press the button quickly (less than 1.5 seconds).

Outline for operating the mode settings

• While operating the mode settings, if you press and hold the MODE button or if you do not operate the button for about 8 seconds, the product returns to standby.
• When you change the setting of a mode, that setting will be displayed first the next time you select that mode.

Measurement

Caution — Controls, adjustments or usage of procedures other than those specified herein may produce negative effects or damage to your health due to laser radiation.

1. Turn on the power.
Press the PWR button to turn on the power.
If you do not operate the button for about 8 seconds, the power turns off automatically.

2. Aim at the target.
Position the target mark on the target whose distance you want to measure.

3. Press the PWR button to measure.

• After measurement, the result is displayed for approx. 8 seconds, then the power automatically turns off.
• Press the PWR button while the power is on to measure again.

* Continuous measurement function
Press and hold the PWR button to start continuous measurement up to approx. 8 seconds. During measurement, the measured result is displayed consecutively while the laser irradiation mark is blinking.
If you release your finger from the button, continuous measurement stops.

Items supplied

Eyepiece cap ×1
Neck strap ×1| Objective lens cap ×2
Lithium battery (CR2) ×1| Soft case ×1
---|---|---

Neckstrap and caps during observation

Neck Strap
Attach the neckstrap as illustrated (B), paying special attention to avoid twisting the strap.

Flip-down objective lens caps
Attach the objective lens caps so that they hang downward when opened as illustrated (C). They are attached correctly if the double-sectioned part (slit) is on the left when viewed from the eyepiece lens side. (They are attached correctly at the time of purchase.)
When observing, you can hang the caps downward from the product as illustrated (D).

Eyepiece cap
There are two ways you can position the eyepiece cap as you observe your subject.

• Remove the eyepiece cap from the eyepieces and allow it to hang from the neckstrap.
• Remove the eyepiece cap from the eyepieces, then detach the right strap from the cap and allow it to hang from the left neckstrap (D).

To attach/detach caps from the neckstrap as shown in image (E) in the following order:

• Attaching: c →b→ a
• Detaching: a→b→ c

Specifications

Measurement system

Measurement range (actual distance)| 9-1,730 m/10-1,900 yd.
Maximum measurement distance (reflective)| 1,730 m/1,900 yd.
Maximum measurement distance (tree)| 1,280 m/1,400 yd.
Maximum measurement distance (deer)| 1,000 m/1,100 yd.
Distance display (increment)| every 0.1 m/yd. (shorter than 100 m/yd.) every 1 m/yd. (100 m/yd. and over)
Optical system
Magnification (x)| 10
Effective diameter of objective lens (mm)| 42
Angular field of view (real) (°)| 6.
Angular field of view (apparent) (°)**| 56.
Field of view at 1,000m/yd. (m/ft)| 107/320
Exit pupil (mm)| 4.
Brightness| 18.
Eye relief (mm)| 16.
Close focusing distance (m/ft)| 7.0/23.0
Interpupillary distance adjustment (mm/in.)| 58-72/2.3-2.8
Diopter adjustment (internal display)| -E4m-1
Others

Operating temperature (°C/°F)|  -20 +60/-4 +140 (Mechanically)
-10 +50/+14 +122 (Electrically)
Operating humidity (0/013H)| 80 or less (without dew condensation)
Power source| CR2 lithium battery x 1 (DC 3V)
Automatic power shut-off (after approx. 8 sec. unoperated)
Dimensions (HxWxD) (mm/in.)| 148 x 131 x 71/5.8 x 5.2 x 2.8
Weight (g/oz)| Approx. 875/30.9 (without battery)
Structure| Waterproof — JIS/IEC protection class 7 (IPX7) equivalent (under Nikon’s testing conditions), fog proof
Electromagnetic compatibility| FCC Part15 subpart B class B, EU:EMC directive, AS/NZS
Environment| RoHS, WEEE
Laser
Laser classification| IEC60825-1: Class 1 M/Laser Product
FDA/21 CFR Part 1040.10:Class I Laser Product
Wavelength (nm)| 905
Pulse duration (ns)| 20
Output (W)| 10
Beam divergence (mrad)| Vertical: 0.062, Horizontal: 1.46

• Reference value. Under Nikon’s measurement conditions.
  ** The number calculated by the formula [tan ω’ = Γ x tanω ]: Apparent field of view: 2ω’ , Magnification: Γ , Real field of view: 2ω
  The specifications of the product may not be achieved depending on the target object’s shape, surface texture, and nature, and/or weather conditions.

Waterproof models

This product has a JIS/IEC protection class 7 (IPX7) equivalent (under Nikon’s testing conditions) waterproof structure.
The product offers the following advantages

• Can be used in conditions of high humidity, dust and rain without risk of damage to internal functions.
• The nitrogen-filled design makes them resistant to condensation and mold.

Observe the following when using the product

• As the unit does not have a perfectly sealed structure, it should not be operated nor held in running water.
• If any moisture is found on movable parts of the unit, stop using it and wipe it off.

Cleaning lens
When using an aerosol-type lens cleaner to clean the objective lenses, carefully clean them by holding the can upright at least 30 cm (11.8 in.) from the lens surface while moving the can to avoid focusing the vaporized liquid gas on one point.

Troubleshooting/Repair

If this product fails to function as expected, check the list before consulting your local dealer or the store where you purchased it.
If there is a problem with the product.

•Check battery insertion
•Replace the battery with a new one
•Check the brightness of the internal display, and adjust it as necessary.
Cover the objective lens so that checking the internal display is easier.
•Unable to measure
•Anomalous result| •Confirm setting
•Confirm if it can measure a large target close to you (for example a building approx. 15m/yd. ahead of you)
•Clean the lens surface if necessary
•Cannot see the internal display
•Difficult to see the internal display| •Check the brightness of the internal display, and adjust it as necessary.
Cover the objective lens so that checking the internal display is easier.

If you require a repair, please contact your local dealer or the store where you purchased the product.
Do not repair or disassemble. It may result in a serious incident.
Please note that Nikon is not responsible for any direct or indirect damage if the user attempts to repair or disassemble.

Nikon Sport Optics

THIS IS YOUR NIKON INC. (Nikon) (VALID IN THE CONTINENTAL UNITED STATES, HAWAII, CENTRAL AND SOUTH AMERICA, AND THE CARIBBEAN) LIMITED WARRANTY FOR NEW NIKON BINOCULARS, RANGEFINDING BINOCULARS AND FIELD SCOPES. YOU MUST PRESENT THIS FORM TOGETHER WITH YOUR PURCHASE RECEIPT THAT DISPLAYS THE PURCHASE DATE TO OBTAIN WARRANTY SERVICE.
NIKON BINOCULAR, RANGEFINDING BINOCULAR AND FIELD SCOPE LIFETIME LIMITED WARRANTY

• Nikon’s Lifetime Limited Warranty applies to the optical system components of this Nikon Binocular, Rangefinding Binocular or Fieldscope, which optical system components are warranted by Nikon to be free from defects in material and workmanship for the lifetime of the product from the date of purchase by the original consumer purchaser from a Nikon authorized dealer
• Nikon’s Seven Year Limited Warranty applies to the non-optical system components of this Nikon Binocular, Rangefinding Binocular or Fieldscope, which non-optical system components are warranted by Nikon to be free from defects in material and workmanship for seven years from the date of purchase by the original consumer purchaser from a Nikon authorized dealer.
• Nikon’s One Year Limited Warranty applies to the electronic components, if any, of this Nikon Binocular, Rangefinding Binocular or Fieldscope, which electronic components, if any, are warranted by Nikon to be free from defects in material and workmanship for one year from the date of purchase by the original consumer purchaser from a Nikon authorized dealer.

During the Lifetime of the Product, Seven Year or One Year time period stated above that applies, if a component of this Binocular, Rangefinding Binocular or Fieldscope is found to be defective in material or workmanship, Nikon will at its option, either repair or replace this Binocular, Rangefinding Binocular or Fieldscope, with a product of comparable specifications and value, without charge, or refund the purchase price shown on your purchase receipt. subject to the following conditions, limitations, and exclusions:

1. This warranty extends to the original consumer purchaser only and is not assignable or transferable.
2. This warranty shall not apply to any product which has been subjected to misuse, abuse, abnormal use, negligence, alteration, accident, or power surge if the product contains electronic components or has had its serial number altered or removed.
3. This warranty does not apply to any defects or damage directly or indirectly caused by or resulting from the use of unauthorized replacement parts and/or service performed by unauthorized personnel.
4. This warranty does not apply to any batteries.

THIS WARRANTY IS MADE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT, AND ALL OTHER OBLIGATIONS ON THE PART OF NIKON PROVIDED, HOWEVER, THAT IF THE DISCLAIMER OF IMPLIED WARRANTIES IS INEFFECTIVE UNDER APPLICABLE LAW, THE DURATION OF ANY IMPLIED WARRANTIES ARISING BY OPERATION OF LAW SHALL BE LIMITED TO THE LIFETIME OF THE PRODUCT, SEVEN-YEAR OR ONE YEAR TIME PERIOD STATED ABOVE THAT APPLIES FROM THE DATE OF PURCHASE OR SUCH LONGER PERIOD AS MAY BE REQUIRED BY APPLICABLE LAW.

NIKON HEREBY DISCLAIMS ANY AND ALL LIABILITY FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL, INDIRECT, EXEMPLARY, OR PUNITIVE DAMAGES ARISING OUT OF OR IN CONNECTION WITH ANY BREACH OF THIS WARRANTY OR ANY OTHER CLAIM WITH RESPECT TO THIS BINOCULAR, RANGEFINDING BINOCULAR, OR FIELD SCOPE, INCLUDING BUT NOT LIMITED TO, CLAIMS OF NEGLIGENCE, STRICT LIABILITY IN TORT OR BREACH OF CONTRACT. SOME STATES DO NOT ALLOW (A) LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR (B) THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

To obtain performance of the warranty obligations, the original consumer purchaser must return this Nikon product together with this warranty form and the purchase receipt displaying the purchase date to the appropriate Nikon service facility. The current address of Nikon’s service facility within the United States can be obtained by visiting www.nikonusa.com/service or by calling 1-800-645-6687.
In returning this Nikon product for repair or replacement or refund under this warranty, the original consumer purchaser must prepay all postage, shipping transportation, insurance and delivery costs, and the Nikon product must be delivered in either its original carton or a similar package affording an equal degree of protection. Nikon will not be responsible for any loss or damage incurred in connection with the return of this Nikon product.
THIS WARRANTY FORM MAY NOT BE REPRODUCED OR COPIED AND WILL BE VALID ONLY WITH AUTHENTIC BINOCULARS, RANGEFINDING BINOCULARS, OR FIELD SCOPES SOLD BY NIKON AND PURCHASED FROM A NIKON AUTHORIZED DEALER.

WU7Y-BF (1909V1)

Documents / Resources

| Nikon 10x42 LaserForce Rangefinder Binocular [pdf] Instruction Manual
10x42 LaserForce Rangefinder Binocular, 10x42 LaserForce, LaserForce, Rangefinder Binocular, Rangefinder, Binocular
---|---

References

• Nikon Service and Repair

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>