GREENROZ Bucket 2.1 Harvest Bucket User Manual
- June 13, 2024
- GREENROZ
Table of Contents
Bucket 2.1 Harvest Bucket
User Manual
Bucket 2.1 Harvest Bucket
THE HARVEST BUCKET
User Manual
GreenBroz.com
SAFETY INSTRUCTIONS
Users shall never place their hands into the bucket during operation. If, at
any time, the user needs to put their hands into the trimming area the drill
must be detached from the trimming shaft and safely stored away from the
bucket.
This machine has rotating parts and pinch points that can cause serious
injury. When powering the machine, ensure that all guards, assemblies, and
accessories have been properly installed. Absolutely no loose hair, clothes,
jewelry, or accessories permitted when operating.
CAUTION
ROTATING MECHANICAL PARTS
Rotating machine parts have the potential to cause severe injury or death.
All components must be fully secured before operation and are essential for
protecting operators. Never place hands or head near the machine during
operation.
TECHNICAL SPECIFICATIONS
Dimensions:
34.78 cm (13.692”) x 30.66 cm (12.069”) x 14.61cm (5.75”)
Weight: 3.73 kg (8.23 lbs.)
Ideal speed: 20-40 RPM
Construction: Made up of food safe materials, including surgical 316 stainless
steel
OPERATING INSTRUCTIONS
Trimming:
After properly assembling the Bucket Trimmer, as shown in the assembly
portion of this manual, the drill is able to be attached. The trimming shaft
is able to be fixed to the drill like any normal drill bit. Open the chuck
until the hex shaft slides in and then full tighten down while making sure the
shaft is not crooked. The shaft is now able to be slid into place for
trimming. Ensure the shaft is fully recessed into both plastic seats before
operating. With the shaft in place, rotate clockwise at low RPM until you have
your desired finish. Note: High RPM can cause damage to the machine or
material.
Bucking:
Some buckets come with a bucking feature built into the clamp itself. There
are various different geometries that will work for most sized plants. Using
the side of the clamp with beveled edges, it is recommended to simply thread
the bottom of the plant through the provided holes and pull through manually.
Ensure to hold the same side of the clamp that is being used to buck.
SCAN QR Code
to see the
How to Operate Harvest Bucket Video
CLEANING INSTRUCTIONS
Tools required for deep cleaning: flat head screwdriver
The machine breaks down for general cleaning without any tools required. For a
deeper clean of each of the components, the tools listed above are required.
The surfaces that come in direct contact with your material should be paid
special attention to. The stainless-steel components are able to be power
washed and sanitized with chemicals as needed. Keep chemicals and high-
pressure water away from the plastic components when cleaning, soap and water
with a rough sponge is recommended.
ASSEMBLY INSTRUCTIONS
Assembly Instructions Step One:
The Bucket Clamp has two sides that hook together as shown in the image. The
clamp is designed to clamp over the top rim of a 5-gallon bucket. After clamp
assembly is placed over a bucket, squeeze the vertical handles together and
rotate the bucket latch into the locked position.
Assembly Instructions Step Two:
Install the Internal Bucket into the clamp with the threaded studs passing
through the slots.
Assembly Instructions Step Three:
Both the top and bottom blades are only dropped into place. It is important to
note that the bottom blade is placed first and that the blades should be
facing opposite directions as shown. The Trim Plate comes next and is secured
with the supplied wing nuts. The shaft and GBZ tines slide into position.
Ensure to place the GBZ tines so that their faces are resting on the Trimming
Plate as shown below.
Fix your drill to the 3/8” hex shaft and rotate clockwise at low RPM (below 50
rpm) until you have your desired finish.
SCAN QR Code
to see the How to Assemble the Harvest Bucket Video
844.DRY.TRIM
[email protected]
greenbroz.com