KATVR C2+ KAT Vehicle Hub Owner’s Manual
- June 13, 2024
- KATVR
Table of Contents
KAT Vehicle Hub
Owner’s Manual
C2+ KAT Vehicle Hub
This product is for personal use ONLY. Any form of commercial application is prohibited.
Acknowledgement
Thank you for purchasing our product!
Please, read this instruction manual carefully and keep it safely stored for
future use.
KATVR reserves the right to interpret and modify the manual. Any amendments,
updates and interpretations to the manual will be published on the KATVR
official website. Please pay attention.
Before using the device in games, read carefully and follow the instructions
of the KAT Vehicle Hub User Manual.
The Vehicle Hub can only be Used with KAT Walk Coord 2, and other application
is prohibited.
Do not install it on other objects. Once installed on the C2+, do not remove.
The KAT Vehicle Hub is designed to provide more efficiency and convenience in VR
locomotion, making the single spot that C2+ takes a 2 in 1 ‒ Walking & Sitting
Spot.
It combined the benefits of haptic feedback simulation of C2+, and the sitting
posture module to create the VR vehicle hub which redefines your VR vehicle
experience letting you not only sit as you drive, but also feel the physical
feedback.
Packing list
Rubber cover: If needed, you may install it to protect the surface from scratches. Small differentces may occur depending on the device version.
Installation Guide
Remove the hole plugs from the supporting rods. Insert the bolts of the inner
mounting plates into the rod holes from inside out. Then, align the openings
of the outer mounting with the bolts and tightly fasten with a hexagon key.
Push the cover down to open it and install the AA battery.
*According to different version: Standard can be opened normally; A reinforced version requires to first remove an extra screw holding the cover. Take out the receiver and plug it into the computer. Pair the sensor (follow the instructions in KAT Gateway). Pairing Button: Press the button for 3 seconds to complete the paring. Indicator light: Blinking light – pairing. Continuous light – pairing completed. Installation complete！Open the sitting posture system as shown above and enjoy your adventure with the KAT Vehicle Hub!
Note: The cushioning material is fabric, it is normal to deform during
use.
Software Guide
Seat Mode Grab the seat-rods and pull them down to unfold the seat module. Sit at any moment whether to interact with the virtual environment in a natural way, or just to relax. Once you sit down, the device will detect it and enter the seat mode as indicated by a short haptic vibration and lock the walking function.
Walking/Sitting switch The module automatically retracts when you stand
up. The sensor will automatically detect your posture and enter the walking
mode with haptic feedback (Depending on the body height and the length of
legs, some users may need to support the module retraction manually).
Haptics
Controller Options for Haptics: C2+ only.
You can customize the functions of haptics. Haptics Module Vibration: You
can open or close the haptics function.
Trigger By Controller Vibration: When ON, the base will vibrate together
with your controller vibration based on different games.
Trigger By Steps: When ON, the base will vibrate when you walk.
Click “Test” buttons for a test of the vibration strength.
Click “-” or “+” to adjust the vibration strength.
Click Default buttons for a reset.
Vehicle Hub mode
The Vehicle Hub fixes the problem of unnatural body postures in which we
usually experience vehicles in VR games.
What’s more, you can open the Vehicle Hub anytime you want to drive a virtual
vehicle for a long trip or any other occasions, even when there is no vehicle
in VR. The vehicle Hub is off by default. Long-press the module button for 1s
to turn on and off as indicated by a short haptic vibration. You can also open
the Vehicle Hub mode by click “ON” in Gateway or Gateway in VR.
Once the Vehicle Hub is enabled, by default it will enter the the ‘AUTO’
vehicle mode in idle state.
IDLE:
Under IDLE, the haptic system will simulate the vibrations of an ignited car
engine awaiting for the beginning of driving.
How To switch “IDLE/MOVING”: You can begin or stop driving by click
“IDLE/MOVING” in Gateway or Gateway in VR. (Coming soon)
You can also do it with the right shoe sensor.
How To Drive/Ride: To begin driving, touch the ground what your right
foot and slide it back. The virtual vehicle will start driving forward, and
the haptic feedback will change to simulate vibration of a car in motion as
well as randomized road events (to help you imagine a more natural driving
environment where your car encounters small obstacles or drives on rough
road).
You can control the direction by turning around. The in-game vehicle will
follow your body direction.
How To Stop: To stop, slide your right foot forward. You can also stand up and stop driving/riding anytime you want to switch back to the waling mode.
Sitting Options
You can customize the functions of KAT Vehicle Hub in the “Sitting” page both
in the PC and VR-integrated version of KAT Gateway for each game.
Vehicle Hub
Explore 4 different types of simulated vehicles.
Click to quickly switch between: Auto / Mount / Aircraft /Heavy Vehicle.
You can also change modes by clicking the main button on the Vehicle Hub. Each
mode has different Vehicle Speed, Road Roughness Simulation (haptic
representation of road holes, stones, etc.) and the haptic vibration strength.
Click “-” or “+” to adjust them based your preferences.
Click “Default” button to reset the settings.
Contact Information
- Company: Hangzhou Virtual and Reality Technology Co., Ltd
- Add: China, Zhejiang Province, Yuhang district of Hangzhou. Wen Yi Xi Lu,1818-2 China Artificial Intelligence Town, Building 6, 9th floor.
- Postal code: 311100
- Email: service@katvr.com
- Web: www.kat-vr.com/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>