PLANET V5 IGS-501T Industrial Gigabit Ethernet Switch User Manual
- June 13, 2024
- PLANET
Table of Contents
User’s Manual
Industrial 5-/8-Port Gigabit
Ethernet Swatch
► IGS-501T/IGS-801T
PLANET Technology Corp.
10F., No. 96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
Warning:
This device is compliant with Class A of CISPR 32.
In a residential environment this device may cause radio interference.
2350-AH0O100-007
Package Contents
Thank you for purchasing PLANET 5-/8-Port 10/100/1000T industrial Gigabit
Ethernet Switch, IGS-501T/IGS-801T. In the following section, the term
“Industrial Gigabit Ethernet Switch” means the IGT-501T/IGT-801T.
Open the box of the Industrial Gigabit Ethernet Switch and carefully unpack
it. The box should contain the following items:
Industrial Gigabit Ethernet
Switch x 1| User’s Manual x 1
---|---
|
DIN-rail Kit x 1| Wall-mount Kit x 1
|
If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.
Product Specifications
| Model | IGS-501T | IGS-801T |
|---|
Hardware Specifications
10/100/1000BASE-T Ports| 5| 8
Dimensions (W x D x H)| 32 x 87 x 135 mm
Weight| 430g| 476g
Power Requirements| 9~48V DC, redundant power with reverse polarity protection
function, 24V AC power support| 12~48V DC, redundant power with reverse
polarity protection function, 24V AC power support
Power Consumption/Dissipation| 2.8 watts/9.5BTU| 6.72 watts/23BTU
Installation| DIN-rail kit and wall-mount ear
Switch Specifications
Switch Processing Scheme| Store-and-Forward
Address Table| 2K| 4K
Buffer| 4M bits| 1.5Mbits SRAM packet buffer
Flow Control| Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Switch Fabric| 10Gbps| 16Gbps
Throughput (packet per second)| 7.4Mpps| 11.9Mpps
Jumbo Frame| 9K
Network Cables| 10/100/1000BASE-T: Cat. 3, 4, 5, 5e, 6 UTP cable (100 meters,
max.)
EIA/TIA-568 100-ohm STP (100 meters, max.)
Standards Conformance
Standards Compliance| IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3az Energy-Efficient Ethernet
IEEE 802.1p Class of Service
Temperature| Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity| Operating: 5% to 90%,
Storage: 5% to 90% (non-condensing)
Regulatory Compliance| FCC Part 15 Class A, CE
Hardware Introduction
Switch Front Panel
The front panel of the Industrial Gigabit Ethernet Switch consists of 5 or 8
auto-sensing 10/100/1000Mbps Ethernet RJ45 ports. The LED Indicators are also
located on the RJ45 ports of the Gigabit Ethernet Switch.
Figures 3-1 and 3-2 show the front panels of the industrial Gigabit Ethernet
Switches.
LED Indicators
IGS-501T:
| LED | Color | Function |
|---|---|---|
| P1 | Green | Lit to indicate power 1 has power. |
| P2 | Green | Lit to indicate power 2 has power. |
| Alarm | Red | Lit to indicate either power 1 or power 2has no power. |
| 1000 LNK/ACT | Green | Lit to indicate the port is successfully connecting to |
the network at 1000Mbps.
Off to indicate that the port is successfully connecting to the network at
10Mbps or 100Mbps.
Blinking to indicate that the port is actively sending or receiving data.
10/100 LNK/ACT| Amber| Lit to indicate the port is successfully connecting to
the network at 100Mbps or 10Mbps.
Off to indicate that the port is successfully connecting to the network at
1000Mbps.
Blinking to indicate that the port is actively sending or receiving data.
IGS-801T:
| LED | Color | Function |
|---|---|---|
| P1 | Green | Lit to indicate power 1 has power. |
| P2 | Green | Lit to indicate power 2 has power. |
| FAULT | Red | Lit to indicate either power 1 or power 2 has no power. |
| 1000 LNK/ACT | Green | Lit to indicate the port is successfully connecting to |
the network at 1000Mbps.
Off to indicate that the port is successfully connecting to the network at
10Mbps or 100Mbps.
Blinking to indicate that the port is actively sending or receiving data.
10/100 LNK/ACT| Amber| Lit to indicate the port is successfully connecting to
the network at 100Mbps or 10Mbps.
Off to indicate that the port is successfully connecting to the network at
1000Mbps.
Blinking to indicate that the port is actively sending or receiving data.
Switch Upper Panel
The upper panel of the Industrial Gigabit Ethernet Switch consists of one
terminal block connector within two DC power inputs.
Figures 3-3 and 3-4 show the upper panel of the Industrial Gigabit Ethernet
Switch.
Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial Gigabit
Ethernet Switch is used for two DC redundant power inputs. Please follow the
steps below to insert the power wire.
When performing any of the procedures like inserting the wires or tightening
the wire-clamp screws, make sure the power is OFF to prevent from getting an
electric shock.
-
Insert positive and negative DC power wires into contacts 1 and 2 for Power 1 or 5 and 6 for Power 2.
-
Tighten the wire-clamp screws for preventing the wires from loosening.
Note
- The wire gauge for the terminal block should be in the range between 12 and 24 AWG.
- The IGS-501T power input range is 9V ~ 48V DC and supports 24V AC.
- The IGS-801T power input range is 12V ~ 48V DC and supports 24V AC.
- Use one power input when using 24V AC.
Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block connector as
the picture shows below. Inserting the wires, the Industrial Gigabit Ethernet
Switch will detect the fault status of the power failure and then form an
open circuit. The following illustration shows an application example for
wiring the fault alarm contacts.
Note
- The wire gauge for the terminal block should be in the range between 12 and 24 AWG.
- Alarm relay circuit accepts up to 24V, max. 1A currents.
Installation
DIN-rail Mounting Installation
The DIN-rail is screwed on the Industrial Gigabit Ethernet Switch when out of
factory. When you need to replace the wallmount application with DIN-rail
application on Industrial Gigabit Ethernet Switch, please refer to the
following figures to screw the DIN-rail on the Industrial Gigabit Ethernet
Switch. To hang the Industrial Gigabit Ethernet Switch, follow the steps
below: Wall-mount Plate Mounting
Side Wall-mount Plate Mounting
Caution| You must use the screws supplied with the wall mounting brackets.
Damage caused to the parts by using incorrect screws would invalidate your
warranty.
---|---
Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resource at the PLANET Web site first to check if it could solve your issue.
If you need more support information, please contact PLANET support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq?method=category&c1=3
Support team mail address:
support@planet.com.tw
Copyright © PLANET Technology Corp. 2021.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
EC Declaration of Conformity
For the following equipment:
Type of Product : 5/8-Port 10/100/1000T Industrial Gigabit Ethernet Switch
Model Number : IGS-501T, IGS-801T
- Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan, R.O.C.
is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (2014/30/EU).
For the evaluation regarding the EMC, the following standards were applied:
| EN 55032 | (2015 + AC:2016) |
|---|---|
| EN 55024 | (2010 + A1:2015) |
| EN 55035 | -2017 |
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231,
Taiwan, R.O.C.
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
Place| May 28, 2018
Date|
---|---|---
PLANET TECHNOLOGY CORPORATION
e-mail: sales@planet.com.tw
http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C.
Tel:886-2-2219-9518 Fax:886-2-2219-9528
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>