hansgrohe 32047000 Talis S2 Basin Mixer Single Lever Instruction Manual
- October 30, 2023
- hansgrohe
Table of Contents
- hansgrohe 32047000 Talis S2 Basin Mixer Single Lever
- Product Information
- Product Usage Instructions
- Models
- Safety Notes
- Installation Instructions
- Technical Data
- Adjustment
- Assembly
- Dimensions
- Spare parts
- Operation
- Troubleshooting
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
hansgrohe 32047000 Talis S2 Basin Mixer Single Lever
Product Information
The product is a shower system with a single-lever mixer and a hot water limiter. It comes with a user manual in multiple languages, including German, French, English, Italian, Spanish, Dutch, Danish, Polish, Russian, Swedish, Lithuanian, Croatian, Turkish, Romanian, Greek, Slovenian, Estonian, Latvian, Norwegian, Bulgarian and Arabic. The product has a maximum operating pressure of 1 MPa and a recommended operating pressure of 1.6 MPa. The hot water temperature is adjustable with the hot water limiter and should not be set too low. The product comes with spare parts and cleaning instructions.
Product Usage Instructions
When installing the shower system, it is important to wear gloves to prevent crushing and cutting injuries. The system should only be used for bathing, hygienic and body cleansing purposes. The hot and cold supplies must be of equal pressure.
To adjust the hot water limiter on single lever mixers, please see page 31 of the manual. No adjustment is necessary when using a continuous-flow water heater. To clean the aerator or replace it if necessary, please follow the instructions on page 36 of the manual. If the mixer is stiff or dripping, or if the hot water temperature is too low, refer to the fault table on page 36 of the manual for possible causes and remedies.
Models
Safety Notes
- Gloves should be worn during installation to prevent crushing and cutting injuries.
- The shower system may only be used for bathing, hygienic, and body cleansing purposes.
- The hot and cold supplies must be of equal pressure.
Installation Instructions
- The fitting must be installed, flushed, and tested after the valid norms.
- Hansgrohe mixers can be used together with hydraulically and thermally controlled continuous flow heaters if the flow pressure is at least 0,15 MPa.
- If the instantaneous water heater causes problems or if you wish to increase the water flow, the EcoSmart® (flow limiter) located behind the aerator can be removed.
Technical Data
This mixer series-produced with EcoSmart® (flow limiter)
- Operating pressure: max. 1 MPa
- Recommended operating pressure: 0,1 – 0,5 MPa
- Test pressure: 1,6 MPa (1 MPa = 10 bar = 147 PSI)
- Hot water temperature: max. 80°C
- Recommended hot water temp.: 65°C
Symbol Description
- Do not use silicone-containing acetic acid!
Adjustment
To adjust the hot water limiter on single lever mixers. No adjustment is necessary when using a continuous-flow water heater.
Assembly
Dimensions
Flow diagram
- with EcoSmart®
- without EcoSmart®
- Talis S² 32047000
- Talis Care 32037000
Spare parts
Operation
open
close
cold
hot
Cleaning (see enclosed brochure.)
Troubleshooting
| Fault | Cause | Remedy |
|---|---|---|
| Insufficient water | – Aerator calcified, dirty | – Clean aerator, replace as |
necessary
Mixer stiff| – Cartridge defective, calcified| – Exchange cartridge
Mixer dripping| – Cartridge defective| – Exchange cartridge
Hot water temperature too low| – Hot water limiter incorrectly set| – Set hot
water limiter
Hansgrohe
Postfach 1145 · D-77761 Schiltach · Telefon +49 (0) 78 36/51-1282 · Telefax
+49 (0) 7836/511440
E-Mail: info@hansgrohe.com · Internet:
www.hansgrohe.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>