Dongguan Taishen Electronics TS-3001 Wireless Charging Night Light Alarm Clock User Manual
- June 13, 2024
- Dongguan Taishen Electronics
Table of Contents
Dongguan Taishen Electronics TS-3001 Wireless Charging Night Light Alarm
Clock
Size Chart
INSTRUCTION
Full display diagram:
Display interface and button indication diagram:
Thank you for purchasing TS-3001 Wireless Charging Night Light Alarm Clock, please read the following instructions before using this product:
Assembly diagram
Step 1: Insert the bracket into the back of the display screen from bottom to top, as shown in the figure:
Step 2: Insert the bracket into the wireless charger, as shown in the figure:
Step 3: Connect the Type-c input port on the back of the display and the Type-c output port of the wireless charger with a Type-c connection power cable:
After assembling according to the above steps, you can access the power line to supply power to use the product .
Main Functions
- Time display I 12/24 hour format selectable)
- Two groups of alarm clocks ( Alarm 1 default 6:00, alarm 2 default 13:00)
- Snooze function ( Snooze time default 5 minutes, 5 ~ 60 minutes can be set)
- Six levels of brightness ( The default is the brightest light)
- RGB night light
- Night mode
- Wireless charging function ( SW/7.SW/lOW/lSW MAX)
Power supply method
1YPE-C power cord CR2032 battery I Battery is not used for power supply,only for memorizing time settings)
Note: The product is shipped without battery.
Default display after power on: Time: 0:00
Time format: 24- hour format
Time Setting
In the time display mode,long press the “MODE” button to enter the time setting mode.After entering, the setting items are displayed and flashing , the setting sequence is: 12/24 hour format selectable–> hour setting-> minute setting–> exit.
When setting 12/24 hour format, short press “UP” or “DOWN” button to switch. When setting the hours and minutes, short press “UP” button to increase one step, Long press “UP”button to increase fast I 8 steps/ second), short press “DOWN” button to decrease one step, long press “DOWN” button to decrease fast ( 8 steps/ second) In the time display mode.short press the “DOWN” button to switch the 12/24 hour format.
Note: If there is no operation for 10 seconds during the setting process,the setting will be saved automatically and the setting mode will be exited.
Alarm Setting:
In the time display mode, short press “ALARM” button to turn on or off the alarm clock. When the alarm clock is turned on, the corresponding alarm icon will be displayed. The setting sequence is: alarm 1 on- alarm 2 onAlarm 1 and alarm 2 are turned on at the sarne tirne off.
In the time display mode, long press “ALARM” button to enter the alarm setting mode, after entering, the setting items are displayed and flashing, the setting sequence is: alarm 1 hour setting➔ alarm 1 minute setting➔ alarm 1 snooze time setting➔ alarm 2 hour setting➔ alarm 2 minute setting ➔ alarm 2 snooze time setting➔ exit.
When setting the hours and minutes, short press “UP” button to increase one
step, long press “UP”button to increase fast ( 8 steps/ second I, short press
“DOWN” button to decrease one step, long press “DOWN” button to decrease fast
I 8 steps/ second).
When setting snooze time ( defaults minutes, 5~60 minutes can be set), short
press “UP” button to increase one step, long press “UP”button to increase fast
( 8 steps/ second), short press “DOWN” button to decrease one step, long press
“DOWN” button to decrease fast ( 8 steps/ second)
Note: If there is no operation for 10 seconds during the setting process, the setting will be saved automatically and the setting mode will be exited.
Snooze Function:
- When the alarm beeps, short press “SNZ/LIGHT” button will enter snooze mode ,the corresponding alarm icon flashing. ( snooze time default 5 minutes, 5-60 minutes can be set I .
- When the snooze time is over, the alarm will beep again.
- Stop the alarm: short press any other buttons execpt “SNZ/LIGHT” button, will stop the alarm or snooze.
Brightness adjustment function
In the time display mode ( The function is not available in snooze mode), short press “SNZ/LIGHT” button to select the display brightness ( default is 100% brightness), the setting sequence is: 100% ➔ 80% ➔ 60% ➔ 40%➔ 20%➔0%.
RGB night light function:
- In the time display mode, short press” ” button to select the RGB light mode, the setting sequence is: RGB Right to Left Flowing Slowly- RGB Right to Left Flowing Quickly–> RGB Changing—> blue-> light blue-> green—> yellow-> red—> purple—>white.
- ln the time display mode, long press” ” button to adjust the brightness of the RGB light, the setting sequence is: bright- medium – dark- off, the default is bright.
Night mode:
- Night mode: LED light automatically enter into the low brightness display status at night I default is 18:00~6:00 I
- In the time display mode, short press the “MODE” button once to enter the night mode, the default off state I display OFF), short press “UP” button or “DOWN” button to turn on or turn off the night rnode. ON means turn on the night mode, OFF means turn off the night mode.
- When the night mode is on ( the screen shows “ON”) , long press the “MODE” button to enter the night rnode setting, the setting sequence is: start hour➔ start minute—-+ end hour–+ end minute.
At start hour and minute setting status, the upper point in the center of the screen is long bright. At end hour and minute setting status, the lower point in the center of the screen is long bright.
Wireless charging function
Wireless charging for phone: 5W/7.5W/10W/15W max.
USB output function
When using the TYPE-C power cable power supply, you can charge your cell phone or other electronic devices through the USB output.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement.
To maintain compliance with FCC’s RF exposure guidelines, the distance must be
at least 20 cm between the radiator and your body, and fully supported by the
operating and installation configurations of the transmitter and its
antenna(s).