VIESSMANN 1344 Luminous Giraffe Fire Brigade On A Trailer with 6 LEDs User Manual

: June 13, 2024
: VIESSMANN

Table of Contents

VIESSMANN 1344 Luminous Giraffe Fire Brigade On A Trailer with 6 LEDs
Model building item, not a toy! Not suitable for children
Wichtige Hinweise
Important information
Safety instructions
- Checking the package contents
Introduction
Mounting
Connection
Warranty
Technical data
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VIESSMANN 1344 Luminous Giraffe Fire Brigade On A Trailer with 6 LEDs

User Manual

Model building item, not a toy! Not suitable for children

under the age of 14 years! Keep these instructions!

Wichtige Hinweise

Bitte lesen Sie vor der ersten Anwendung des Produktes bzw.dessen Einbau diese Bedienungsanleitung aufmerksam durch und bewahren Sie diese auf. Sie ist Teil des Produktes.

Important information

Please read this manual completely and attentively before usingthe product for the first time. Keep this manual. It is part of the product.

Safety instructions

Caution:

Risk of injury!

Tools are required for installation.

Electrical hazard!

Never put the connecting wires into a power socket! Regularly examine the transformer for damage. In case of any damage, do not use the transformer.
Make sure that the power supply is switched off when you mount the device and connect the cables!
Only use VDE/EN tested special model train transformers for the power supply!
The power sources must be protected to avoid the risk of burning cables.

Using the product for its correct purpose

This product is intended:

For installation in model train layouts and
For connection to an authorized model train transformer (e. item 5200).
For operation in dry rooms

Using the product for any other purpose is not approved and is considered inappropriate. The manufacturer is not responsible for any damage resulting from the improper use of this product.

Checking the package contents

Check the contents of the package for completeness:

LED model with base socket
Retaining ring
Manual

Introduction

This LED model uses SMD LEDs to produce light matching the lamp model. Low heat build-up and power input. Nearly unlim- ited lifetime of the LEDs, so no more change is required.

Mounting

Remove the LED model carefully from the
Check function before
Drill a hole (Ø 5 mm) at the mounting place (see fig. 1).
Put the cables from outside through the hole and push the socket into the If necessary, fasten the LED model with the retaining ring from inside (optional).

Connection

While connecting the cables, leave a loop of about 2 – 3 cm length below the LED model, so that you can pull and reverse the LED model from the mounting hole during any work.
Connect the LED model to the lighting power output of a model train transformer (e. g. item 5200) or power supply as shown in fig. 4 and/or 5.
DC voltage: Connect the diode (red part with black mark) with the plus pole of the power supply, the resistor with the minus pole.
AC voltage: Operation with AC voltage could cause some flickering. We recommend to use the Viessmann power module, item 5215, which is sufficient for ca. 100 LED lamps or reflectors (fig. 5). Connect the cable to the diode with the brown output socket, the resistor with the red output socket of the power module.

Warranty

Each model is tested to its full functionality prior to delivery. The warranty period is 2 years starting from the date of purchase. Should a fault occur during this period please contact our service department (service @viessmann-modell.com). Please send the item to the Viessmann service department for check- ing and repair only after consultation. If we find a material or production fault to be the cause of the failure, the item will be repaired free of charge or replaced. Expressively excluded from any warranty claims and liability are damages of the item and consequential damages due to inappropriate handling, disre- garding the instructions of this manual, inappropriate use of the model, unauthorized disassembling, construction modifications and use of force, overheating and similar.

Technical data

Änderungen vorbehalten. Keine Haftung für Druckfehler und Irrtümer.
Die aktuelle Version der Anleitung finden Sie auf der Viessmann Homepage unter der Artikelnummer.
Subject to change without prior notice. No liability for mistakes and printing errors.
You will find the latest version of the manual on the Viessmann website using the item number.