viessmann 6088 Hanging Industrial Lamp Instruction Manual

: June 13, 2024
: VIESSMANN

Table of Contents

viessmann 6088 Hanging Industrial Lamp
Product Information
Product Usage Instructions
Important information
Introduction
Mounting
Connection
Technical data
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

viessmann 6088 Hanging Industrial Lamp

Model building item, not a toy! Not suitable for children under the age of 14 years! Keep these instructions!

Product Information

The product is a lighting accessory designed for use in model train layouts and dioramas. It can be connected to a power supply to provide lighting effects. The product is available in different models, including H0 Hanging industrial lamps with LED warm-white (item 6086) and H0 Hanging industrial lamps modern with LED white(item 6088).

The product operates on either DC voltage or AC voltage. When using DC voltage, the diode (red part with black mark) should be connected to the plus pole of the power supply, and the resistor should be connected to the minus pole. When using AC voltage, it is recommended to use the Viessmann power module (item 5215) to avoid flickering. The cable should be connected to the diode with the brown output socket, and the resistor should be connected to the red output socket of the power module. The product has a maximum operating voltage of approximately 24 V~ and a nominal operating current of approximately 10 mA.

Product Usage Instructions

Read the user manual carefully before using the product.
Ensure that the product is suitable for your model train layout or diorama.
If using DC voltage:
- Connect the diode (red part with black mark) to the plus pole of the power supply.
- Connect the resistor to the minus pole of the power supply.
If using AC voltage:
- Use the Viessmann power module (item 5215) for flicker-free lighting.
- Connect the cable to the diode with the brown output socket of the power module.
- Connect the resistor to the red output socket of the power module.
Ensure that the diode and resistor are not cut off.
Refer to the figures in the user manual for visual reference.
Keep the product away from children under the age of 14.
Refer to the Viessmann website for the latest version of the user manual using the item number.

Important information

Please read this manual completely and attentively before using the product for the first time. Keep this manual. It is part of the product.

Safety instructions

Caution: Risk of injury!

Due to the detailed reproduction of the original and the intended use, this product can have peaks, edges and breakable parts. Tools are required for installation.

Electrical hazard

Never put the connecting wires into a power socket! Regularly examine the transformer for damage. In case of any damage, do not use the transformer.
Make sure that the power supply is switched off when you mount the device and connect the cables!
Only use VDE/EN tested special model train transformers for the power supply!
The power sources must be protected to avoid the risk of burning cables.

Using the product for its correct purpose

This product is intended:

For installation in model train layouts and dioramas.
For connection to an authorized model train transformer (e. g. item 5200).
For operation in dry rooms only.

Using the product for any other purpose is not approved and is considered inappropriate. The manufacturer is not responsible for any damage resulting from the improper use of this product.

Checking the package contents

Check the contents of the package for completeness:

LED-lamp with connection cables, resistor and diode
Manual

Introduction

This LED model uses SMD LEDs to produce light matching the lamp model. Low heat build-up and power input. Nearly unlimited lifetime of the LEDs, so no more change is required.

Mounting

Remove the lamp carefully from the package.
Check the function before mounting.
Determine the mounting place (e. g. under roof or ceiling)
Drill a hole (Ø 2 mm) at the mounting place (see fig. 1).
Direct the cables to the connection point and fix them, if necessary, with a bit glue at the wall/ceiling or at the floor.

Caution: Resistor and diode at the cables are needed for proper function of the LED model. Never cut them off! Never cover resistor or diode with insulation material, because they have to be cooled by surrounding air!

Connection

While connecting the cables, leave a loop of about 2 – 3 cm length below the LED model, so that you can pull and reverse the LED model from the mounting hole during any work.
Connect the LED model to the lighting power output of a model train transformer (e. g. item 5200) or power supply as shown in fig. 2 and/or 3.
DC voltage: Connect the diode (red part with black mark) with the plus pole of the power supply, the resistor with the minus pole.
AC voltage: Operation with AC voltage could cause some flickering. We recommend to use the Viessmann power module, item 5215, which is sufficient for approx. 100 LED lamps or reflectors (fig. 3). Connect the cable to the diode with the brown output socket, the resistor with the red output socket of the power module.

Technical data

Operating voltage: 10 – 16 V AC ~
- (with and without 5215 power module)
- 14 – 24 V DC =
- 13 – 24 V digital signal
Operating current: ca. 10 mA

Subject to change without prior notice. No liability for mistakes and printing errors.
You will find the latest version of the manual on the Viessmann website using the item number.