viessmann 1343 Luminous Giraffe on a Trailer with 6 LEDS Instruction Manual
- June 13, 2024
- VIESSMANN
Table of Contents
viessmann 1343 Luminous Giraffe on a Trailer with 6 LEDS
Product Information:
This product is a model building item and not a toy. It is not suitable for children under the age of 14 years. Please keep these instructions for future reference.
The product is designed for installation in model train layouts and dioramas. It can be connected to an authorized model train transformer (e.g. item 5200). The product is intended for use in dry rooms only. Any other use of the product is not approved and may result in damage for which the manufacturer is not responsible.
The package includes an LED model with a base socket, a retaining ring, and a manual.
Product Usage Instructions
- Important Information:
- Read the entire manual carefully before using the product for the first time and keep it for future reference.
- Ensure the product is used with the appropriate tools during installation.
- Never insert the connecting wires into a power socket to avoid electrical hazards.
- Regularly inspect the transformer for any damage. If damaged, do not use it.
- Make sure to switch off the power supply when mounting the device and connecting cables.
- Only use VDE/EN tested special model train transformers for the power supply.
- Protect the power sources to prevent cable burning.
- Using the Product:
- This product is specifically designed for installation in model train layouts and dioramas.
- Connect the product to an authorized model train transformer, such as item 5200.
- Only operate the product in dry rooms.
- Using the product for any other purpose is considered inappropriate and may result in damage for which the manufacturer is not responsible.
- Checking Package Contents:
- Verify that the package contains an LED model with a base socket, a retaining ring, and a manual.
- Introduction:
- This LED model utilizes SMD LEDs to produce light that matches the lamp model.
- The product generates low heat and requires minimal power input.
- The LEDs have an almost unlimited lifetime, eliminating the need for frequent replacements.
LED-Modell mit Steckfuß Ø 5,5 mm
LED-model with base socket Ø 5,5 mm
Model building item, not a toy! Not suitable for children under the age of 14 years! Keep these instructions!
Important information
Please read this manual completely and attentively before using the product for the first time. Keep this manual. It is part of the product.
Safety instructions
Caution:
Risk of injury!
Tools are required for installation.
Electrical hazard!
Never put the connecting wires into a power socket! Regularly examine the
transformer for damage. In case of any damage, do not use the transformer.
Make sure that the power supply is switched off when you mount the device and
connect the cables!
Only use VDE/EN tested special model train transformers for the power supply!
The power sources must be protected to avoid the risk of burning cables.
Using the product for its correct purpose
This product is intended:
- For installation in model train layouts and dioramas.
- For connection to an authorized model train transformer (e. g. item 5200).
- For operation in dry rooms only.
Using the product for any other purpose is not approved and is considered inappropriate. The manufacturer is not responsible for any damage resulting from the improper use of this product.
Checking the package contents
Check the contents of the package for completeness:
- LED model with base socket
- Retaining ring
- Manual
Introduction
This LED model uses SMD LEDs to produce light matching the lamp model. Low
heat build-up and power input. Nearly unlimited lifetime of the LEDs, so no
more change is required.
Mounting
- Remove the LED model carefully from the package.
- Check function before mounting.
- Drill a hole (Ø 5.5 mm) at the mounting place (see fig. 1).
- Put the cables from outside through the hole and push the socket into the hole. If necessary, fasten the LED model with the retaining ring from inside (optional).
Caution:
Never touch the mast but only the base socket (fig. 3).
Connection
Caution:
Resistor and diode at the cables are needed for proper function of the LED
model. Never cut them off! Never cover resistor or diode with insulation
material, because they have to be cooled by surrounding air!
While connecting the cables, leave a loop of about 2 – 3 cm length below the
LED model, so that you can pull and reverse the LED model from the mounting
hole during any work.
Connect the LED model to the lighting power output of a model train
transformer (e. g. item 5200) or power supply as shown in fig. 4 and/or 5.
DC voltage: Connect the diode (red part with black mark) with the plus pole of
the power supply, the resistor with the minus pole.
AC voltage: Operation with AC voltage could cause some flickering.
We recommend to use the Viessmann power module, item 5215,which is sufficient
for ca. 100 LED lamps or reflectors (fig. 5). Connect the cable to the diode
with the brown output socket, the resistor with the red output socket of the
power module.
Warranty
Each model is tested to its full functionality prior to delivery. The warranty
period is 2 years starting from the date of purchase.
Should a fault occur during this period please contact our service department
(service@viessmann-modell.com). Please send the item to the Viessmann service
department for checking and repair only after consultation. If we find a
material or production fault to be the cause of the failure, the item will be
repaired free of charge or replaced. Expressively excluded from any warranty
claims and liability are damages of the item and consequential damages due to
inappropriate handling, disregarding the instructions of this manual,
inappropriate use of the model, unauthorized disassembling, construction
modifications and use of force, overheating and similar.
Technical data
-
Operating voltage: 10 – 16 V AC ~ (with and without item 5215, power modul)
14 – 24 V DC =
13 – 24 V digital signal -
Operating current: ca. 10 mA
Do not dispose of this product through (unsorted) domestic waste, supply it to recycling instead.
Subject to change without prior notice. No liability for mistakes and printing
errors.
You will find the latest version of the manual on the Viessmann website using
the item number.
Viessmann Modelltechnik GmbH
Bahnhofstraße 2a
D – 35116 Hatzfeld-Reddighausen
info@viessmann-modell.com
+49 6452 9340-0
www.viessmann-modell.de
Made in Europe
92890
Stand 11/sw
09/2021
Ho/Kf
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>