VIESSMANN 3570 Rotating Flashing Light Instruction Manual
- June 13, 2024
- VIESSMANN
Table of Contents
- VIESSMANN 3570 Rotating Flashing Light Instruction Manual
- Model building item, not a toy! Not suitable for children under the age
- Bedienungsanleitung Operation Manual
- 4. Technical data
- 1. Important information
- 1.1 Safety instructions
- Caution:
- Using the product for its correct purpose
- Mounting
- Mounting with a bracket
- Connection
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
VIESSMANN 3570 Rotating Flashing Light Instruction Manual
Model building item, not a toy! Not suitable for children under the age
of 14 years! Keep these instructions
Entsorgen Sie dieses Produkt nicht über den (unsortierten) Hausmüll, sondern
führen Sie es der Wiederverwertung zu.
Do not dispose of this product through (unsorted) domestic waste, supply it to
recycling instead
Bedienungsanleitung Operation Manual
Bitte lesen Sie vor der ersten Anwendung des Produktes bzw. dessen Einbau
diese Bedienungsanleitung aufmerksam durch.
Bewahren Sie diese auf, sie ist Teil des Produktes
- If the rotating flashing light works as desired, put the shrink tubes over the joints and heat them up shortly with a hot air gun or a gas lighter (fig. 11).
- In order to hide the control electronics underneath the layout, drill a hole of 4.5 mm diam. beneath the vehicle (fig. 12)
4. Technical data
Operating voltage: max. 16 V AC~ / DC= (also for digital current)
1. Important information
Please read this manual completely and attentively before using the product for the first time. Keep this manual. It is part of the product.
1.1 Safety instructions
Caution:
Risk of injury!
Due to the detailed reproduction of the original and the intended use, this
product can have peaks, edges and breakable parts. For installation tools are
required.
Electrical hazard!
Never put the connecting wires into a power socket! Regularly examine the
transformer for damage. In case of any damage, do not use the transformer!
Make sure that the power supply is switched off when you mount the device and
connect the cables! Only use VDE/EN tested special model train transformers
for the power supply!
The power sources must be protected to prevent the risk of burning cables
Using the product for its correct purpose
This product is intended:
- For installation in H0 model vehicles.
- For operation with a power supply up to 16 V AC~ / DC=.
- For operation in dry rooms only.
Using the product for any other purpose is not approved and isconsidered inappropriate. The manufacturer is not responsiblefor any damage resulting from the improper use of this product
Checking the package contents
Check the contents of the package for completeness:
- Rotating flashing light with LED and control electronics
- 2 brackets
- Manual
Mounting
– Test the function prior to mounting. Follow chapter 3
Mounting directly onto the roof
- Drill a hole at the mounting site with a diameter of 2.5 mm(fig. 1).
- Apply a little glue to the underside of the rotating flashing light(fig. 2).
- Insert the cable through the hole and then fit in the flashinglight (fig. 3).
- Arrange the cables inside the vehicle and fasten them in some spots with a little glue, if necessary.
Mounting with a bracket
- Insert the cables through the adapter ring (fig. 4).
- Plug the bracket into the adapter ring up to the stop (fig. 5).If needed, the bracket may be shortened.
- Place the wires into the groove of the bracket (fig. 6)
- Drill a hole at the mounting site with a diameter of 1.5 mm(fig. 7.1/7.2).
- Insert the cables and the bracket from above through thehole. Fasten the flashing light with some glue to the mountingsite (fig. 8.1/8.2).`
- Arrange the cables inside the vehicle and fasten them in some spots with a little glue, if necessary
Connection
– Connect the rotating flashing light with the control electronics (fig. 9).
– Connect the control electronics acc. to fig. 10 to a model train transformer
(item 5200).
– Should you prefer to invert the running direction of the LEDs, just exchange
2 random wires between flashing light and control electronics (fig. 9)
– If the rotating flashing light works as desired, put the shrink tubes over
the joints and heat them up shortly with a hot air gun or a gas lighter (fig.
11).
– In order to hide the control electronics underneath the layout, drill a hole
of 4.5 mm diam. beneath the vehicle (fig. 12).
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>