VIESSMANN 6366 Light Hanging with Rope Instruction Manual

: June 13, 2024
: VIESSMANN

Table of Contents

Important Information
Introduction
Mounting
Connection
Warranty
Technical Data
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VIESSMANN 6366 Light Hanging with Rope

VIESSMANN 6366 Light Hanging with Rope

Important Information

Please read this manual completely and attentively before using the product for the first time. Keep this manual. It is part of the product.

Safety instructions

Caution

Risk of injury!

Due to the detailed reproduction of the original and the intended use, this product can have peaks, edges and breakable parts. Tools are required for installation.

Electrical hazard!
Never put the connecting wires into a power socket! Regularly examine the transformer for damage. In case of any damage, do not use the transformer.
Make sure that the power supply is switched off when you mount the device and connect the cables!
Only use VDE/EN tested special model train transformers for the power supply!
The power sources must be protected to avoid the risk of burning cables.

Using the product for its correct purpose

This product is intended:
– For installation in model train layouts and dioramas.
– For connection to an authorized model train transformer (e. g. item 5200).
– For operation in dry rooms only.
Using the product for any other purpose is not approved and is considered inappropriate. The manufacturer is not responsible for any damage resulting from the improper use of this product.

Checking the package contents

Check the contents of the package for completeness:
– LED-light hanging
– 2 rope suspensions
– Manual

Introduction

This model uses SMD LEDs to produce light matching the lamp model. Low heat build-up and power input. Nearly unlimited lifetime of the LEDs, so no more change is required.

Mounting

Remove the lamp carefully from the package.
Check function before mounting.
Drill a hole (Ø 1.5 mm) into a wall for mounting the rope suspension.
Drill a hole (Ø 2 mm) into the opposite wall to insert the connection cables and to fasten the second rope suspension.
Insert the connection cables into the holes and fasten the rope suspensions (fig. 1). Guide the cables through the recess in the ropes.
Tension the retaining rope and fasten the two ends with knots or glue.

Connection

Caution :
Resistor and diode at the cables are needed for proper function of the LED model. Never cut them off! Never cover resistor or diode with insulation material, because they have to be cooled by surrounding air!

While connecting the cables, leave a loop of about 2 – 3 cm length below the LED model, so that you can pull and reverse the LED model from the mounting hole during any work.
Connect the LED model to the lighting power output of a model train transformer (e. g. item 5200) or power supply as shown in fig. 2 and/or 3.
Connection

DC voltage: Connect the diode (red part with black marker) with the plus pole of the power supply, the resistor with the minus pole.
AC voltage: Operation with AC voltage could cause some flickering.
We recommend to use the Viessmann power module, item 5215, which is sufficient for approx. 100 LED lamps or reflectors (fig. 3). Connect the cable to the diode with the brown output socket, the resistor with the red output socket of the power module.

Warranty

Each model is tested to its full functionality prior to delivery. The warranty period is 2 years starting from the date of purchase.
Should a fault occur during this period please contact our service department (service@viessmann-modell.com). Please send the item to the Viessmann service department for checking and repair only after consultation. If we find a material or production fault to be the cause of the failure, the item will be repaired free of charge or replaced. Expressively excluded from any warranty claims and liability are damages of the item and consequential damages due to inappropriate handling, disregarding the instructions of this manual, inappropriate use of the model, unauthorized disassembling, construction modifications and use of force, overheating and similar.

Technical Data

Operating voltage: 10 – 16 V AC ~ (with and without item 5215, power module) 14 – 24 V DC = 13 – 24 V digital signal
Operating current: ca. 10 mA

Do not dispose of this product through (unsorted) domestic waste, supply it to recycling instead.

Subject to change without prior notice. No liability for mistakes and printing errors.
You will find the latest version of the manual on the Viessmann website using the item number.