VIESSMANN 6016 LED Lights and Spots with Wall Holder Instruction Manual
- June 13, 2024
- VIESSMANN
Table of Contents
LED lights and spots
with wall holder
Ø 2,5 mm
Operation Manual
Model building item, not a toy! Not suitable for children under the age of 14 years! Keep these instructions!
Important information
Please read this manual completely and attentively before using the product
for the first time. Keep this manual. It is part of the product.
1.1 Safety instructions
Caution:
Risk of injury!
Due to the detailed reproduction of the original and the intended use, this
product can have peaks, edges and breakable parts. For installation tools are
required.
Electrical hazard!
Never put the connecting wires into a power socket! Regularly examine the
transformer for damage. In case of any damage, do not use the transformer.
Make sure that the power supply is switched off when you mount the device and
connect the cables! Only use VDE/EN tested special model train transformers
for the power supply! The power sources must be protected to prevent the risk
of burning cables.
1.2 Using the product for its correct purpose
This product is intended:
- For installation in model train layouts and dioramas.
- For connection to an authorized model train transformer (e. g. item 5200) or a digital command station.
- For operation in dry rooms only.
Using the product for any other purpose is not approved and is considered inappropriate. The manufacturer is not responsible for any damage resulting from the improper use of this product.
1.3 Checking the package contents
Check the contents of the package for completeness:
- LED light or spot with wall holder
- Retaining ring (not with all models)
- Manual
Introduction
This lamp produces the light by SMD-LEDs which is suitable for the lamp model. Low heat build-up and power input. Nearly unlimited lifetime of the LED, so no more change is required.
Mounting
- Remove the lamp carefully from the package.
- Check function before mounting.
- Drill a hole (Ø 2.5 mm) at the mounting place (fig. 1).
- Put the base socket with the cables from above through the hole. If necessary, fasten the lamp with the retaining ring from the bottom to the ground plate.
When connecting the cables, please leave a loop of ca. 2 – 3 cm behind the
lamp, which enables you to pull the lamp out of the mounting hole.
Caution:
Resistor and diode at the cables are needed for proper function of the lamp.
Never cut them off! Never cover resistor or diode with insulation material,
because they have to be cooled by surrounding air!
Connection
Connect the LED light to the light output of a model train transformer (e. g.
item 5200) as shown in fig. 5 and/or 6.
DC voltage: Connect the diode (red part with black marker) with the
positive pole and the resistor with the negative pole of the power supply.
AC voltage: Operation with AC voltage could cause some flickering. We
recommend to use the Viessmann power module, item 5215 (fig. 6) which is
sufficient for ca. 100 LEDs or spots. Connect the cable with the diode to the
brown output socket and the cable with the resistor to the yellow output
socket (fig. 5).
Technical data
| Operating voltage: | 10 – 16 V AC~ (with and without item 5215, power module) |
|---|---|
| Operating current: | 14 – 24 V DC=13 – 24 V digital signal ca. 10 mA |
Never cut off diode and
resistor.
HINT: Power module, item 5215
- Offers flicker-free lighting when using AC power.
- Nearly double brightness is possible.
Do not dispose of this product through (unsorted) domestic waste, supply it to
recycling instead.
Subject to change without prior notice. No liability for mistakes and printing
errors.
You will find the latest version of the manual on the Viessmann website using
the item number.
Viessmann Modelltechnik GmbH
Bahnhofstraße 2a
D – 35116 Hatzfeld-Reddighausen
info@viessmann-modell.com
+49 6452 9340-0
www.viessmann-modell.de Made in
Europe
86008
Stand 09/sw
03/2023
Ho/Kf ****
References
- Welcome to the Modell Group
- Que Faire de mes Déchets ? Découvrez les solutions pour tous vos déchets et nos conseils pour en produire moins.
- Viessmann Modelltechnik GmbH
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>