SHENZHEN JUNYE ELECTRONICS V80015HP Wireless Headphone User Manual

SHENZHEN JUNYE ELECTRONICS V80015HP Wireless Headphone

Product Information

• Playing time: about 6 hours

• Charging time: about 2 hours

• Volume Control: Short press to decrease the volume, long press for next song

• Power On/Off: Long press to power on/off

• Call Functions: Play/Pause short press to answer incoming call, press for 2 seconds to reject

• Mode Change: Short press to increase the volume, long press for previous song mode change

• TF Memory Card Socket: Supports memory cards up to 32GB

• Indicator Light/Microphone: Indicates device status and includes a built-in microphone

• Audio Line Socket: Allows connection of an audio line

• Compliance: This device complies with part 15 of the FCC Rules.
  It must not cause harmful interference and must accept any interference received.

• FCC Warning: Any changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment.

• RF Exposure Requirement: The device meets general RF exposure requirements and can be used in portable exposure conditions without restriction.

Product Usage Instructions

1. To decrease the volume, short press the volume control button.
   To skip to the next song, long press the volume control button.

2. To power on/off the device, long press the power button.

3. To answer an incoming call, short press the play/pause button.
   To reject a call, press the play/pause button for 2 seconds.

4. To increase the volume, short press the volume control button.
   To change to the previous song mode, long press the volume control button.

5. The device supports TF memory cards up to 32GB. Insert the memory card into the TF memory card socket.

6. The indicator light indicates the device’s status, and the built-in microphone allows for audio recording or voice calls.

7. Connect an audio line to the audio line socket for audio output.

8. Ensure compliance with FCC rules regarding interference and RF exposure requirements.

9. Do not make any changes or modifications to the device without approval, as it may void the user’s authority to operate the equipment.

Product Parameters

Pairing and Connection

1. Keep the distance between the mobile phone and the headset within 1 m; the closer, the better.
2. Press and hald the key “ ” for about 5 seconds, and then release it when the red and the blue lamps alternately blink. At this time, the headset has entered the paring mode.
3. Enable the Bluetooth function of the mobile phone, search the Bluetooth equipment, select “V80015 Headphones” for paring and connection. After connection is successful, the blue indicating lamp of the headset slowly blinks.

Notes:

• If there is no BT connection within 5 minutes, the headphone will be powered off automatically
• After pairing iscompleted, the headset and the handset will remember eachother, without pairing

INSRTCUTION

Label
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC warning

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>