Infinix X6710 Note 30 Smartphone User Manual

Infinix X6710 Note 30 Smartphone

Product Information

The Infinix X6710 is a mobile phone that comes with various features and components. Some of the key specifications and parts of the phone include:

• OLED PROTECT FILM: Protective film for the OLED display
• WIRELESS CHARGING: Capability to charge the phone wirelessly
• BACK LENS: Lens on the back of the phone
• MAIN PCBA: Main Printed Circuit Board Assembly
• NFC: Near Field Communication technology
• FRONT COVER ASM: Front cover assembly
• BCAM 2M: Back camera with 2 megapixels resolution
• SIM CARD HOLDER: Slot for SIM card
• BAT COVER: Battery cover
• RCAM LENS 2M: Rear camera lens with 2 megapixels resolution
• USB RUBBER: Rubber component for USB port
• AMOLED TP: Touch panel using AMOLED technology
• FLASH FPC: Flexible Printed Circuit for flash module
• UP SPK ASM: Upper speaker assembly
• BATTERY: Phone battery
• FCAM 32M: Front camera with 32 megapixels resolution
• BCAM 108M: Back camera with 108 megapixels resolution
• MID FRAME ASM: Middle frame assembly
• RCAM LENS 108M: Rear camera lens with 108 megapixels resolution
• RCAM FLASH LENS: Rear camera flash lens
• SIDEKEY: Side buttons on the phone
• BCAM HOLDER 2M: Holder for back camera with 2 megapixels resolution
• EARJACK RUBBER: Rubber component for earphone jack
• SUB PCBA: Sub Printed Circuit Board Assembly
• CABLE LINE2: Secondary cable line
• VC: Vibration motor component
• MOTOR: Motor component
• FLASH LIGHT TAPE: Tape for flash light
• CABLE LINE1: Primary cable line
• DOWN SPK: Lower speaker component
• FCAM HOLDER: Holder for front camera
• IN-SCREEN FP CAM: In-screen fingerprint camera

Product Usage Instructions

SIM/SD Card Installation
To install a SIM card or SD card in your Infinix X6710, follow these steps:

1. Power off your mobile phone.
2. Refer to the provided picture in the user manual for the correct placement and orientation of the SIM and SD cards.

Charging the Phone
To charge your Infinix X6710, you have two options:

• Using a charger: Connect the provided INFINIX charger to the phone’s charging port and plug it into a power outlet.
• Using a USB cable: Connect the provided USB cable to the phone’s charging port and connect the other end to a computer’s USB port.

Note:
It is important to use only the INFINIX charger and cables that come with the phone. Using other chargers or cables may cause damage to the device and void your phone warranty.

FCC Caution
The Infinix X6710 complies with Part 15 of the FCC Rules. Please be aware of the following:

• This device should not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
• Any changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment.

Specific Absorption Rate (SAR) Information
This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations.

Operating System
The Infinix X6710 operates on AndroidTM operating system, which is a trademark of Google LLC.

Explosion diagram specification

Know your phone

1. Front camera
2. Volume + key
3. Volume – key
4. Power key
5. NFC

SIM/SD card installation

1. Power off mobile.
2. Refer to the following picture for SIM/SD card installation.

Charging the phone

• You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone).
• Use only INFINIX charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.

FCC Caution

Labelling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Information to user
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Information to the user

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information:
This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.

FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: X6710 (FCC ID: 2AIZN-X6710) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.190W/kg and when properly worn on the body is 0.614W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10 mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that does not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.

Operating System: AndroidTM Android is a trademark of Google LLC.

References

• Patents - DTS
• Patents - DTS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>