MARLEY Stir It Up Wireless Turntable Record User Guide

: June 13, 2024
: MARLEY

Table of Contents

MARLEY Stir It Up Wireless Turntable Record
Product Information
Product Usage Instructions
**PRODUCT MAP
FUNCTION LAYOUT
SETUP
LINE OUT OPERATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MARLEY Stir It Up Wireless Turntable Record

MARLEY-Stir-It-Up-Wireless-Turntable-Record-
PRODUCT

Product Information

The Stir It Up Wireless is a turntable that allows you to play vinyl records wirelessly. It comes with various features and components to enhance your listening experience.

Product Map

Spindle
Turntable
45 Adaptor
Balance Weight
Anti-Skating Knob
Tone Arm Lift Level
Tone Arm Rest Holder
Tone Arm
Stylus
Needle Cover
Off/33/45 Knob
Power Adaptor With 4 Interchangeable Plugs

Function Layout

E. – VOL + Knob
F. Headphone Jack
G. Anti-skating Knob
A. OFF/ON PRE-AMP Switch
B. Output Selector (45/33 RPM)
C. Power Indicator
D. Bluetooth Indicator

Product Usage Instructions

Powering On Your Stir It Up Wireless

Ensure the power adaptor is properly connected to the turntable.
Switch on the power using the OFF/ON PRE-AMP switch (A).

Attaching the Drive Belt
Note: The drive belt comes pre-installed. However, if there is no visible belt around the sub-platter and motor, please re-fit the belt.

Open the turntable.
If necessary, re-fit the drive belt around the sub-platter and motor.

Playing a Record
Note: Use the 33 RPM speed for 33-sized vinyl discs and the 45 RPM speed for 45-sized vinyl discs.

Place the desired vinyl disc on the turntable.
Select the appropriate RPM speed using the Off/45/33 knob (11).
To power off the unit, rotate the RPM Dial knob to the offposition.

Anti-Skating
The anti-skating compensates for inward tracking forces that occur with certain pick-ups when the stylus nears the center of the record. Adjust the anti-skating knob (5) as needed.

Note : During adjustment, leave the tone arm and balance weight alone to prevent damaging the stylus (needle).

Volume Control

To increase volume, rotate the Volume Knob clockwise.
To decrease volume, rotate the Volume Knob counter clockwise.

Headphone Operation via Headphone Jack
Connect a set of headphones (not included) to the headphone jack (F). Make sure to plug in the headphone before putting them on.

Line Out Operation
Note: Switch off the power to all equipment before making connections.

Switch the PRE-AMP OFF/ON switch (A) to the ON position.
Plug one end of the RCA cable (included) into the LINE OUT socket at the back of the unit.
Plug the other end of the cable into the LINE IN socket of your home amplifier device.
Switch on the unit and the connected amplifier device.
Adjust the volume on the amplifier device.

**PRODUCT MAP

$MARLEY-Stir-It-Up-Wireless-Turntable-Record-FIG- $1$$ **

LEGEND

Spindle
Turntable
45 Adaptor
Balance Weight
Anti-Skating Knob
Tone Arm Lift Level
Tone Arm Rest Holder
Tone Arm
Stylus
Needle Cover
Off/33/45 Knob
Power Adaptor With 4 Interchangeable Plugs

FUNCTION LAYOUT

LEGEND

A. RCA Line Out
B. Pre-Amp Switch Button
C. Off/33/45 Knob
D. Bluetooth® Button
E. – VOL + Knob
F. Headphone Jack
G. Anti-skating Knob

SETUP

POWERING ON YOUR STIR IT UP WIRELESS

Your Stir It Up Wireless uses an AC power supply and is powered by a standard wall outlet.
Connect the power adaptor to the wall outlet.

ATTACHING THE DRIVE BELT

Note : The drive belt comes pre-installed. However, if when you open the turntable, there is no visible belt around the sub-platter and motor. Please re-fit the belt.

To fit the belt, put the belt on the motor (this is the gold spindle), then keeping the belt tight stretch it around the sub-platter. Once in place make sure the belt if flat and not twisted.
Now place the metal platter on the black sub-platter, by aligning the centre holes.
Now place the REGRIND™ silicone slip mat on the metal platter, again aligning the centre holes. The platter should be attached to the base.

BLUETOOTH® PAIRING

Power on the external Bluetooth® device first before turning on the BT function on the Turntable.
Press the BT button on the turntable to turn on Bluetooth® transmitter.
Press button again to enable the unit to search the Bluetooth® device till BT indicator light becomes solid. This will indicated your devices are paired.

NOTE: If the Turntable does not pair with your Bluetooth® device within 30 seconds, press the Bluetooth® search button again on the turntable and it should pair.

Blue LED light flash
Blue LED light stable

DISCONNECT BLUETOOTH® PAIRING

Long press and hold the BT button till the BT indicator light turns off. Turntable will then disconnect from external device.

Blue LED light will turn off.

PLAYING A RECORD

Put a vinyl record on the turntable.
Assemble the balance weight and set it to a proper position.
To adjust the balance weight rotate the balance weight at counter-clock wise.
Lift and move the tone arm to turntable. Place the tone arm on the edge of the record.
Turn the RPM Dial knob to select the speed according to the record you are playing.
The turntable platter will auto stop when the music has ended. Lift the tone arm and place it to tone arm rest manually. $MARLEY-Stir-It-Up-Wireless-Turntable-Record-FIG- $8$$

To listen to side B, flip record and repeat the above steps.

33 RPM speed to play corresponding size 33 vinyl disc
45 RPM speed to play corresponding size 45 vinyl disc

To power the unit off Rotate the RPM Dial knob to the off position

Note:

Remove the needle cover before you balance the tone arm.
Hold tone arm whenever you make any adjustment or action so as to protect the tone arm.
Do not try to adjust the balance weight while playing a record as this could break the needle and scratch the record.
Re-secured the tone arm before transportation to protect the needle.
Remove the balance weight before transportation to prevent damage or breakage to the unit.
Do not stop or turn the platter manually. Moving or jarring the turntable without securing the Tone armclamp could result in damage to the Tone arm.

ANTI-SKATING

Normally the anti-skating should be set to its minimum setting. Anti-skate compensates for inward tracking forces that occur with certain pick-up when the stylus nears the center of the record. If the turntable is experiencing excessive skipping while nearing the center spindle, try increase the anti- skating in the increments indicated on the dial. Start by adding an increment of 1, test its performance, then increase it more, and so on.

Note : During adjusting the anti-skating knob, leave the tone arm and balance weight alone to prevent damaging the stylus (needle).

VOLUME CONTROL

Increase Volume : Rotate the Volume Knob clockwise.
Decrease Volume : Rotate Volume Knob counter clockwise.

HEADPHONE OPERATION VIA HEADPHONE JACK

Connect a set of headphone (not included) in the headphone jack.

Note : Never put on the headphone till you have plugged in the headphone plug

NON BLUETOOTH® CONNECTION SETUP

CAUTION : Switch off the power to all equipment before making connections. Read the instructions of each component you intend to use with this unit. Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the signal interconnection cables together with the AC power cord.

LINE OUT OPERATION

Switch the PRE-AMP OFF/ON SWITCH to ON position.
Plug one end of the RCA cable (included) into the LINE OUT socket at the back of the unit. Be sure to match the color with the socket.
Plug the other end of the cable into the LINE IN socket of your home amplifier device.
Switch on the unit and the amplifier device you connected.
Adjust the volume on the amplifier device.

COMPLIANCE INFO

STIR IT UP WIRELESS
READ ALL INSTRUCTIONS BEFORE USE AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

FCC RF EXPOSURE STATEMENT:
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

CAUTION! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ISEDC STATEMENT

This device complies with Innovation, Science, and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the device.

The device complies with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. This Class B digital apparatus complies with Canadian ICES-003.

ISEDC RF EXPOSURE STATEMENT:

The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.

To prevent possible hearing damage, do not listen at high volume levels for long periods. Full instruction and warranty details can be found at http:// www.thehouseofmarley.com/ instructionbooks

|

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment

---|---
| This symbol indicates class II equipment
| This symbol indicates AC voltage
| This symbol indicates for indoor use only
The power adaptor plug is used as the disconnect device, The connected AC power outlet must be located near the equipment and be easily accessible.
The marking information is located at the bottom of the apparatus.

Marley and the Marley logo are registered trademarks of Fifty-Six Hope Road Music Limited and the use of such marks by House of Marley is under license. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by The House of Marley is under license.

Operating frequency band: 2402 – 2480MHz
CE Maximum radio-frequency power transmitted: 3.09dBm

DISTRIBUTED BY:
The House of Marley, LLC 3000 North Pontiac Trail, Commerce Township, MI 48390 USA

Imported into the UK by FKA Brands Ltd, Tonbridge, TN110GP, UK.
Imported into the EU by FKA Brands Ltd, 29 Earlsfort Terrace, Dublin 2. IE IB-EMJT002SB EM-JT002B