MAXXAIR 3900 MAXXShade Blind for Maxxfan Rooflight Skylight Instruction Manual

MAXXAIR 3900 MAXXShade Blind for Maxxfan Rooflight Skylight

Product Information: MAXXAIR MAXXShade 3900 & 3901

The MAXXAIR MAXXShade 3900 & 3901 is a ventilation system designed for general ventilation use. It is manufactured by AIRXCEL, INC. The product comes with installation instructions, information, and an operating guide. Please read and save these instructions for future reference.

Important Safety Precautions:

• Use this unit only as intended by the manufacturer. If you have any questions, contact the manufacturer.
• Before servicing or cleaning the unit, switch off the power at the service panel and lock the service disconnecting means to prevent accidental power switch-on. If locking is not possible, securely fasten a prominent warning device to the service panel.
• Do not use this unit to exhaust hazardous or explosive materials or vapors.
• Installation work and electrical wiring must be done by qualified individuals in accordance with applicable codes and standards, including fire-rated construction.

Product Part Number: 10-03911Z (May 2018)

Product Usage Instructions

Step 1: Garnish Ring Removal

Remove the four screws that hold the garnish ring to the ceiling. Discard the screws. Be careful to prevent the garnish ring from falling on the installer.

Step 2 (LED MAXXShade Model): Disconnect Power

Prior to installing the LED MAXXShade, disconnect the main power supply of the vehicle.

Step 3: LED Wire Connection

(LED MAXXShade Model) Insert the black LED wire into the closed end connector on the side with the hinge. Slide the open side of the closed end connector over the positive (+) power supply wire. Close the clip on the closed end connector to complete the circuit and provide power to the LED light. Repeat this step for the second power wire and white LED light wire. Ensure that the power wires slide to the interior and do not become entangled.

Step 4: Assemble Adapter and Garnish Ring

Assemble the adapter over the garnish ring and attach it to the ceiling using the provided screws. Ensure that the power wires are not caught in the mounting screws during adapter installation.

Step 5: Assemble MAXXShade Shroud

Attach the MAXXShade shroud to the adapter, aligning the flanges properly.

Step 6 (LED MAXXShade Model): Restore Power

Restore power to the vehicle to complete the installation of the LED MAXXShade.
For any further assistance or questions, refer to the product manual or contact the manufacturer.

INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS
NOTE: Refer to Installation Instructions, Information and Operation Guides regarding the model you have purchased.
The MAXXAIR MAXXShade mounts over the MAXXFAN garnish ring to provide a shade option to your MAXXFAN or a shade with “COOL WHITE” LED light. The MAXXShade shade is made of light blocking material and the frame provides passive ventilation.
The MAXXAIR MAXXShade will mount over competitor’s vent fans to provide shade or shade with LED lighting by simply drilling holes in the competitor’s garnish ring to accommodate the MAXXShade adapter.
The LED lighted MAXXShade requires a minimum 12 Volt DC, 2 amp service. Confirm that the circuit you intend to use will accommodate the additional load. The circuit must be fused and use appropriate gauge stranded wire for electrical connections.
NOTE: THE FAN SHOULD NOT BE OPERATED WHEN THE SHADE IS CLOSED. In some instances, the fan may overheat when used while the shade is closed.
WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by AIRXCEL, INC. If you have questions, contact the manufacturer.
2. Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
   CAUTION! FOR GENERAL VENTILATION USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR VAPORS.

INSTALLATION INSTRUCTIONS – ALL MODELS

WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

NOTE:
To make the installation easier, it would be helpful to have a second person to assist.

1. STEP 1
   Remove the four (4) screws that hold the garnish ring to the ceiling. Discard the screws. NOTE: Removal of these screws allows the garnish ring to fall so care should be taken to prevent the garnish ring from falling on installer.

2. STEP 2
   (LED MAXXShade Model)
   IMPORTANT! Disconnect main vehicle power before installation of LED MAXXShade. With the Garnish Ring out, locate the power supply wires to the MAXXFAN. Gently pull on the vehicle power supply wires to create some slack for connecting the LED wires.

3. STEP 3
   Assemble the Adapter over the Garnish Ring and attach to the ceiling with the four (4) screws provided with the MAXXShade to secure the Adapter and Garnish Ring to the ceiling. On LED lighted MAXXSHADE, be sure the power wires will not be caught in the mounting screws during adapter installation.

4. STEP 3
   (LED MAXXShade Model)
   Insert black LED wire as far as it will go into the closed end connector on the side with the hinge. Slide the open side of the closed end connector over the positive (+) power supply wire. Close the clip on the closed end connector which completes the circuit to provide power to the LED light. Repeat the above step for the second power wire and white LED light wire. Make sure the power wires slide to the interior and do not become entangled.

5. STEP 4
   Assemble the MAXXShade shroud to the adapter, lining up the flanges.

6. STEP 5 (LED MAXXShade Model)
   Restore power to the vehicle.
   THIS COMPLETES THE INSTALLATION

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>