MAXXAIR MAXXShade 3900 Rooflight Skylight Installation Guide
- June 13, 2024
- MAXXAIR
Table of Contents
MAXXAIR MAXXShade
INSTALLATION INSTRUCTIONS, INFORMATION AND OPERATING GUIDE
FOR MAXXAIR MAXXSHADE 3900 & 3901
READ
AND SAVE THESE INSTRUCTIONS
MAXXShade 3900 Rooflight Skylight
NOTE: Refer to Installation Instructions, Information and Operation
Guides regarding the model you have purchased.
The MAXXAIR MAXXShade mounts over the MAXXFAN garnish ring to provide a shade
option to your MAXXFAN or a shade with “COOL WHITE” LED light. The MAXXShade
shade is made of light blocking material and the frame provides passive
ventilation.
The MAXXAIR MAXXShade will mount over competitor’s vent fans to provide shade
or shade with LED lighting by simply drilling holes in the competitor’s
garnish ring to accommodate the MAXXShade adapter.
The LED lighted MAXXShade requires a minimum 12 Volt DC, 2 amp service.
Confirm that the circuit you intend to use will accommodate the additional
load. The circuit must be fused and use appropriate gauge stranded wire for
electrical connections.
NOTE: THE FAN SHOULD NOT BE OPERATED WHEN THE SHADE IS CLOSED. In some
instances, the fan may overheat when used while the shade is closed.
WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by AIRXCEL, INC. If you have
questions, contact the manufacturer.
b) Before servicing or cleaning the unit, switch power off at service panel
and lock the service disconnecting means to prevent power from being switched
on accidentally. When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag, to the service
panel.
CAUTION! FOR GENERAL VENTILATION USE ONLY. DO NOT USE TO EXHAUST
HAZARDOUS OR EXPLOSIVE MATERIALS OR VAPORS.
INSTALLATION INSTRUCTIONS ALL MODELS
WARNING! TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING: Installation work and electrical wiring must
be done by qualified person(s) in accordance with all applicable codes and
standards, including fire-rated construction.
NOTE: To make the installation easier, it would be helpful to have a
second person to assist.
STEP 1 Remove the four (4) screws that hold the garnish ring to the
ceiling. Discard the screws.
NOTE: Removal of these screws allows the garnish ring to fall so care
should be taken to prevent the garnish ring from falling on installer.
STEP 2 (LED MAXXShade Model)
IMPORTANT! Disconnect main vehicle power before installation of LED
MAXXShade.
With the Garnish Ring out, locate the power supply wires to the MAXXFAN.
Gently pull on the vehicle power supply wires to create some slack for
connecting the LED wires.
STEP 3 Assemble the Adapter over the Garnish Ring and attach to the
ceiling with the four (4) screws provided with the MAXXShade to secure the
Adapter and Garnish Ring to the ceiling. On LED lighted MAXXSHADE, be sure the
power wires will not be caught in the mounting screws during adapter
installation.
STEP 3
(LED MAXXShade Model)
Insert black LED wire as far as it will go into the closed end connector on
the side with the hinge. Slide the open side of the closed end connector over
the positive (+) power supply wire. Close the clip on the closed end connector
which completes the circuit to provide power to the LED light. Repeat the
above step for the second power wire and white LED light wire. Make sure the
power wires slide to the interior and do not become entangled.
STEP 4 Assemble the MAXXShade shroud to the adapter, lining up the
flanges.
STEP 5 (LED MAXXShade Model) Restore power to the vehicle.
THIS COMPLETES THE INSTALLATION
More information https://www.caravansplus.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>