Galaxy Press GS-205B Galaxy Tumbler Press Instruction Manual

Press GS-205B Galaxy Tumbler Press
Instruction Manual

Operation Manual
(GS-205B Plus)

Safety Instructions

When using your heat press, basic precautions should always be followed, including the following:

1. Read all instructions.

2. Use heat press only for its intended use.

3. To reduce the risk of electric shock, do not immerse the heat press in water or other liquids.

4. Never pull cord to disconnect from outlet, instead grasp plug and pull to disconnect.

5. Do not allow cord to touch hot surfaces, allow heat press to cool completely before storing.

6. Do not operate heat press with a damaged cord or if the equipment has been dropped or damaged. To reduce the risk of electric shock, do not disassemble or attempt to repair the heat press. Take it to a qualified service person for
   examination and repair. Incorrect assembly or repair could increase the risk of fire, electric shock, or injury to persons when the equipment is used.

7. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use  of the appliance by a person responsible for their safety.

8. Close supervision is necessary for any heat press being used by or near children.
   Do not leave equipment unattended while connected.

9. Burns can occur when touching hot metal parts.

10. To reduce the likelihood of circuit overload, do not operate other high voltage equipment on the same circuit.

11. If an extension cord is necessary, then a 20 amperage rated cord should be used.
    Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over.

Technical Parameters

Machine View

Control Panel Guide

Operation Instructions

1. Connecting the System
   1.1 Connect the power cord into a properly grounded electrical outlet with a sufficient amperage rating.
   1.2 VOLTAGE
   120 Volt – The GS-205B requires a full 10 amp grounded circuit for 120 volt operation.
   240 Volt –The GS-205B requires a full 7 amp grounded circuit for 240 volt operation.
   1.3 EXTENSION CORDS If used, should be as short as possible and not less than 12 gauge. Heavy duty cords are recommended.
   1.4 CIRCUITS that have less than 10 amps or that have other high demand equipment or appliances(especially more than one heat seal machine) plugged in, should not be used.
   NOTE: If the supply cord is damaged, it must be replaced by the manufacturer, its service agentora similarly qualified person in order to avoid hazard.
   CAUTION :
   Failure to follow these instructions will cause:

1. Erratic controller functions.
2. Inaccurate displays and slow heat-up.
3. The circuit breaker to disengage.

Turn On the System
2.1 Switch The System On(figure2.1)![Galaxy Press GS 205B Galaxy Tumbler Press

• System](https://manuals.plus/wp-content/uploads/2023/09/Galaxy-Press-GS- 205B-Galaxy-Tumbler-Press-System.png)

Adjusting the Temperature

3.1 Press the “set” button once time.
“Temperature” lights will illuminate, press the “up” and “down” button to set target start temperature (see figure 3.1)
3.2 Press the “set” button second time.
“Setting” lights will illuminate, press the “up” and “down” button to set printing temperature (see figure 3.1)

Adjusting the Time

4.1 Once you have adjusted the temperature, press the “set” button again. “Time” lights located in the display will illuminate. (see figure 4.1)
4.2 Next, press the “up” and “down” button to set target printing time. The time setting rangeland be set from 0~999.

Adjusting the Pressure

5.1 The Pressure Adjustment Knob is located as picture.(See figure 5.1)
5.2 Adjust the pressure by turning the knob clockwise to increase pressure and counter clockwise to decrease pressure.
REMEMBER: To allow for the thickness of your garment when adjusting the pressure.

Printing And Pressing

• Once your equipment has reached the designated start temperature:
• Position mug and application and proceed to press.
• This procedure will start the automatic timing process.
• Please note machine will heat up from start temperature to printing temperature then time starts to count down.
• The timer will automatically count down to zero then circuit board will alarm when the press cycle is complete.
• The timer will automatically re-set and you are ready to continue with the next application.

Switch Between F/C

7.1 Press “set” button for 4 seconds to enter into second level menu. Display as below.(see figure 7.1)
7.2 Press “set” button to select “SL2” mode(See figure 7.2)
7.3, press up and down button to set value at 0 or 1, 0 for Celsius, 1 for Fahrenheit.
7.4 Press “set” button 4 seconds to quit.

Temperature Calibration

8.1 Press “set” button for 4 seconds to enter into second level menu. Display as below.(see figure 8.1)
8.2 Press “set” button to select “Pb” mode (See figure 8.2)
8.3 press “up” and “down” button to make temperature calibration.
8.4 Press “set” button 4 seconds to quit.

if temperature on heater is higher than circuit board shows,pls raise the Pb value.
Example:
Heater temperature:190C
Circuit board temperature:185C
Pls set Pb Value at ( +5 )
If temperature on heater is lower than circuit board shows,pls reduce the Pb value.
Example:
Heater temperature:185C
Circuit board temperature:190C
Pls set Pb Value at ( -5 )

Exploded Views And Parts List

Electrical Schematic

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>