HAMPTON DAY Heater Glen 5 Piece Small Space User Guide

June 4, 2024
HAMPTON DAY

HAMPTON-DAY-Heater-Glen-5-Piece-Space-LOGO

HAMPTON DAY Heater Glen 5 Piece Small Space

HAMPTON-DAY-Heater-Glen-5-Piece-Space-PRODUCT

Important Safety Instructions

READ ALL INSTRUCTIONS BEFORE USE
To reduce the risk of injury to persons:

  1. Close supervision is necessary when this furnishing is used by or near children, or disabled persons, if applicable.
  2. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

SAVE THESE INSTRUCTIONS.

  • DANGER : Keep children out of the assembly area during assembly.
  • CAUTION : Do not use sharp equipment such as a knife and scissors when removing the protective material, as it may damage the product.
  • WARNING : Do not sit or stand on the table.
  • WARNING : Do not stand on the chair.

Warranty

TWO YEAR LIMITED WARRANTY

WHAT IS COVERED
The frame is warranted to be free of manufacturing defects for two year from the purchase date. If the frame of your furniture fails (ie. broken frame or weld) within two year of ownership, Hampton Bay will repair, provide replacement parts, or replace the product at our option. Frame finishes are warranted against blistering, cracking, or peeling for two year from purchase date. This is a residential use warranty only. Warranty is void when product is used for commercial settings. This warranty is a limited warranty and applies to the original purchase only. Proof of purchase is required.
Contact the Customer Service Team at 1-800-841-1350 or visit hamptonbay.com

Care and Cleaning

  • Use mild soap and warm water to clean the frames.
  • Rinse with clean water and dry thoroughly.
  • Be sure to drain any water accumulated inside the frames. To thoroughly drain frames, remove footcaps and tilt frames, if necessary, to remove all water. Water allowed to accumulate inside the frames and then exposed to sub-freezing temperatures can cause damage to frame tubing. Such damage caused by conditions other than normal is not covered under warranty.
  • Any rust spots should be lightly sanded and treated with rust inhibitor and followed with an application of touch-up paint (not included).

Table Assembly

PLANNING ASSEMBLY
Before beginning the assembly of this product, make sure all parts are present. Compare parts with Package Contents and Hardware Included lists. If any part is missing or damaged, do not attempt to assemble the product, and return it to the place of purchase. Assembly requires two people.

HARDWARE INCLUDEDHAMPTON-DAY-Heater-Glen-5-Piece-Space-
FIG-1

Part Description Quantity
AA Bolt M6*15mm 16
CC Washer 16
DD Hex Wrench 1

NOTE : Hardware not shown to actual size.

PACKAGE CONTENTS

Part Description Quantity
I Table Top 1
J Table Leg 4
  1. Attaching the Legs to the Table TopHAMPTON-DAY-Heater-Glen-5-Piece-Space-FIG-3
    • Place the Table Top (I) upside down on a soft, clean and level surface.
    • Insert the Legs (J) into the Table Top (I), by using the Bolts (AA) and the Washers (CC).
    • Tighten all the bolts with the Hex Wrench (DD).
  2. Completing the AssemblyHAMPTON-DAY-Heater-Glen-5-Piece-Space-FIG-4
  3. Turn the table over, then adjust self-leveling feet on table for equal balance (as shown).
  4. Now the table is ready to use.

Chair Assembly

PLANNING ASSEMBLY
Before beginning the assembly of this product, make sure all parts are present. Compare parts with Package Contents and Hardware Included lists. If any part is missing or damaged, do not attempt to assemble the product, and return it to the place of purchase. Assembly requires two people.

NOTE: Hardware not shown to actual size.

HARDWARE INCLUDEDHAMPTON-DAY-Heater-Glen-5-Piece-Space-
FIG-5

Part Description Quantity
AA Bolt M6*15mm 24
BB Bolt M6*25mm 12
CC Washers 36
DD Hex Wrench 1

PACKAGE CONTENTSHAMPTON-DAY-Heater-Glen-5-Piece-Space-
FIG-6

Part Description Quantity
A Front Leg 2
B Chair Seat 2
C Chair Back 2
H Back Leg 4
K Seat Cushion 2
L Back Cushion 2
  1. Connecting the Front Leg to the Chair SeatHAMPTON-DAY-Heater-Glen-5-Piece-Space-FIG-7
    • Connect the Front Leg (A) to Seat (B) using the Bolts (BB) and Washers (CC).
    • Do not overtighten all the bolts.
  2. Connecting the Chair Back to the Chair seat & Front LegsHAMPTON-DAY-Heater-Glen-5-Piece-Space-FIG-8
    • Connect the Chair Back (C) to the assembled Chair Seat (B) and Front Leg (A) using the Bolts (AA & BB) and Washers (CC) as shown.
    • Do not overtighten bolts (BB) during this step.
  3. Inserting the Back Legs to the Chair SeatHAMPTON-DAY-Heater-Glen-5-Piece-Space-FIG-9
    • Insert the Back Legs (H) to the Chair Seat (B), by using Bolts (AA) and Washers (CC) and Hex Wrench (DD).
  4. Put the Seat and Back Cushions on the ChairHAMPTON-DAY-Heater-Glen-5-Piece-Space-FIG-10
    • Turn the Chair over and place on a flat surface
    • Tighten all the bolts on the seat with the Hex Wrench (DD).
    • Put the Seat Cushion (K) and Back Cushion (L) on the chair.
    •  The Chair now is ready to use.

Ottoman Assembly

PLANNING ASSEMBLY
Before beginning the assembly of this product, make sure all parts are present. Compare parts with Package Contents and Hardware Included lists. If any part is missing or damaged, do not attempt to assemble the product, and return it to the place of purchase. Assembly requires two people.

NOTE : Hardware not shown to actual size.

HARDWARE INCLUDEDHAMPTON-DAY-Heater-Glen-5-Piece-Space-
FIG-11

Part Description Quantity
AA Bolt M6*15mm 8
BB Bolt M6*25mm 12
CC Washers 20
DD Hex Wrench 2

PACKAGE CONTENTSHAMPTON-DAY-Heater-Glen-5-Piece-Space-
FIG-12

Part Description Quantity
D Leg 4
E Ottoman Seat 2
F Side Panel 4
K Seat Cushion 2
  1. Connecting the Legs to the Ottoman SeatHAMPTON-DAY-Heater-Glen-5-Piece-Space-FIG-13
    • Connect the legs (D) to the Ottoman Seat (E), by using the Bolts (BB) and Washers (CC).
    • Do not overtighten all the bolts.
  2. Inserting the Side Panel to the assembled seatHAMPTON-DAY-Heater-Glen-5-Piece-Space-FIG-14
    • Turn the assembled Ottoman Seat over and place on a flat surface.
    • Insert the Side Panels (F) to the assembled Ottoman Seat, by using the Bolts (AA & BB) and Washers (CC) as shown.
    •  Then tighten all bolts with the Hex Wrench (DD).
  3. Put the cushion on the OttomanHAMPTON-DAY-Heater-Glen-5-Piece-Space-FIG-15
    • Put the Seat Cushion (K) on the assembled Ottoman Seat.
    • Now the Ottoman is ready to use.

Questions, problems, missing parts? Before returning to the store, call Hampton Bay Customer Service
8 a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday
1-800-841-1350
HAMPTONBAY.COM
Retain this manual for future use.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals