Lenovo U1 Smart Lock User Manual

: June 13, 2024
: Lenovo

Table of Contents

Lenovo U1 Smart Lock
Product Information
Product Usage Instructions
ADMINISTRATOR MENU
ENTER TO ADMINISTRATOR MODE
USER SETTING
SYSTEM SETTING
SYSTEM INQUIRY
NETWORK SETTINGS
METHOD OF USE
PRODUCT INTRODUCTION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Lenovo U1 Smart Lock

Product Information

Menu	Sub Menu	Description
ADMINISTRATOR MENU	User Settings	Add or delete user passwords, fingerprints,

Product Usage Instructions

Enter Administrator Mode

a. Touch the key area to turn on the keyboard light.
b. Press [*] twice, enter the management password, and press [#] to confirm.
c. Voice prompt: “You have entered the management mode.”
d. If there is no administrator set, you need to add the management password.

User Settings
To add user fingerprints, passwords, and cards:

Unlocking Method	Sub Menu	Description
Fingerprint	ADD FINGERPRINT	Record fingerprints from multiple angles and add

them to the
system.
Pincode| ADD PINCODE| Add a 6-8 digit door unlocking pincode.
RFID Tag| ADD RFID TAG| Add a user card by placing it near the magnetic card
identification area.

To delete user fingerprints, passwords, and cards:

Unlocking Method	Sub Menu	Description
Fingerprint	DELETE FINGERPRINT	Delete a single user fingerprint or delete

all
fingerprints.
Pincode| DELETE PINCODE| Delete a single user pincode or delete all pincodes.

Note : Follow the voice prompts during the above operations.

CAUTION
During the above operation, you can follow the voice prompts.

ENTER TO ADMINISTRATOR MODE

a. Touch the key area, and then the keyboard light will be on.
b. First press [*] twice, then enter the management password and then press [#] to confirm.
c. Voice prompt: “You have entered the management mode”.
d. Under the factory default, there is no administrator. In such a case when using the lock for the first time, the user needs to add the management password.

CAUTION
If the identification of the administrator fails, it will give a voice “input error”. If the identification is successful, directly enter the main menu, press the [*] key to exit, and press the corresponding number to enter the sub-menu.

USER SETTING

Enter the user setting mode, to add user fingerprint, password, and card, and select the operation below according to the unlocking method you need to add.

ADD FINGERPRINT

a. Press [*] twice to enter management mode, press [1] to enter the user setting mode, and then press [1] to add the user fingerprint.
b. Input the user number that needs to add a fingerprint, and press [#] to confirm.
c. Place the fingerprint to be added on the fingerprint collector, when you hear “please take away your finger and put it again” take away your finger and put it back into the fingerprint area five times and when you hear “add successfully”, the user fingerprint will be added successfully.

CAUTION
When recording fingerprints, it is recommended to collect fingerprints from multiple angles up and down, left and right.

ADD PINCODE

a. Press [*] twice to enter management mode, press [1] to enter user setting mode, and then press [2] to add user Pincode.
b. Input the three-digit user numbers, and press [#] to confirm.
c. Enter the 6-8 digit door unlocking pincode you want to add and press [#] to confirm, and then input the door opening pincode again and press [#] to confirm. It would be completed when you hear the voice prompt “add successfully”.

ADD RFID TAG

a. Press [*] twice to enter management mode, press [1] to enter user setting mode, then press [3] to add user cards.
b. Input the three-digit user numbers, and press [#] to confirm.
c. Put the card near to the magnetic card identification area, until you hear the voice prompt “add successfully”.

DELETE FINGERPRINT

a. Press [*] twice to enter management mode, press [1] to enter user setting mode, and then press [4].
b. Press [1] to delete a single user, Input the user number to be deleted, and press [#] to confirm. It will be completed until you hear the voice prompts “delete successfully”.
c. Press [2] to enter the delete all mode. It will be completed until you hear the voice prompts “delete successfully”.

DELETE PINCODE

a. Press [*] twice to enter management mode, press [1] to enter user setting mode, and then press [5].
b. Press [1] to delete a single user, input the user number to be deleted, press [#] to confirm. It wil be completed until you hear the voice prompts “delete successfully”.
c. Press [2] to enter the delete all mode. It will be completed until you hear the voice prompts “delete successfully”.

DELETE RFID CARD

a. Press [*] twice to enter management mode, press [1] to enter user setting mode, and then press [6].
b. Press [1] to delete a single user. Enter the user number that needs to be deleted, press [#] to confirm. It will be completed until you hear the voice prompts “delete successfully”.
c. Press [2] to enter the delete all mode. It will be completed until you hear the voice prompts “delete successfully”.

MODIFY ADMINISTRATOR PASSWORD

a. Press [*] twice to enter management mode. Press [1] to enter the enter user setting mode and then press [7] to change the administrator password.
b. Enter the new administrator password (6-8 digits), press [#] to confirm, enter the new management password again, press [#] to confirm. It will be completed until you hear the voice prompts “set successfully”.

CAUTION
After the installation is completed, please change the management password in a timely manner.

SYSTEM SETTING

VOLUME SETTING

a. Press [*] twice to enter the management mode, press [2] to enter the system setting mode then press [1] to enter the volume settings;
b. Press [1] to set the high volume mode. It will be completed until you hear the voice prompts “set successfully”.
c. Press [2] to set the medium volume mode. It will be completed until you hear the voice prompts “set successfully”.
d. Press [3] to set the low volume mode. It will be completed until you hear the voice prompts “set successfully”.
e. Press [4] to set the mute mode. It will be completed until you hear the voice prompts “set successfully”. No voice prompts for the whole system in mute mode (except alarm tone and operation management menu).

SYSTEM INQUIRY

ANTI-COUNTERFEITING CODE INQUIRY
Press [*] twice to enter the management mode. Press [3] to enter the system inquiry, then press [1] to enter the anti-counterfeiting code inquiry,and the voice prompt will announce the anti-counterfeiting code of this lock.

TIME INQUIRY
Press [*] twice to enter the management mode, press [3] to enter the system query, and then press [2] to enter the time query, and the voice prompt will announce the current smart lock system time.

NETWORK SETTINGS

(ONLY WIFI VERSION IS AVAILABLE)
Press [*] twice to enter the management mode, press [4] to enter the network settings, press [1] to turn on the network, press [2] to turn off the network.

METHOD OF USE

OPERATION IN THE COMMON MODE
PINCODE UNLOCK

a. Add the password, and press [#] to confirm. It will mean to complete the successful password verification, when you hear the voice prompt “Verified successfully please open the door”.
b. Press the handle down to open the lock.

CAUTION
You can add any dummy password before and after the user password, and the length of the password including the dummy password should not

FINGERPRINT UNLOCK

a. Put the finger of which fingerprint has been added in the correct way on the fingerprint collector. When fingerprint verification success, it will give the voice prompt “Verified successfully, please open the door”.
b. Press the handle down to open the lock.

RFID TAG UNLOCK

a. Put and expose the induction card which has been added to the keyboard area. When the induction card is verified successfully it will give the voice prompts “Verified successfully please open the door”.
b. Press the handle down to open the lock

LOCK THE DOOR

LOCK EXTERNALLY
Lift the handle upward outdoor to unlock the door
LOCK INTERNALLY
Lift the handle upward indoor to unlock the door
DOUBLE LOCK
Turn the knob which the door can’t unlock from outdoor

UNDER THE SECURITY MODE

a. Press [*] twice to enter the management mode, press [2] to enter the [system settings] press [2] to enter the door opening mode setting and then press [2] to select the security mode, it will give the voice prompt “set successfully”.
b. Under the security mode, any two combinations of fingerprint, password and card, can be use to unlock the door.

EMERGENCY OPENING METHOD MECHANICAL KEY
In case of emergency such as forgetting the password, running out of battery power or the system cannot operate, you can use the mechanical key to unlock the door.

a. Insert the mechanical key into the spare mechanical key port under the lock.
b. After turning the key, press down the handle to unlock the lock.

MICRO USB POWER SUPPLY
When the battery runs out and there is no brass key, you can connect an external rechargeable battery or 5V1A power supply for emergency power supply, and open the door according to the normal operation steps. After opening the door with emergency power, please replace the battery in the lock in time.

NORMALLY OPEN FUNCTION

a. Press [*] twice to enter the management mode, press [2] to enter the system setting, and then press [2] to enter the door opening mode setting.
b. According to the voice prompt, press [3] to select the normally open mode.
c. Under the normally open mode, press the outdoor handle to unlock the door.
d. In the normally open mode, press [999] + [#] to exit the normally open mode.

TRY TO RELEASE THE FROZEN-STATE FUNCTION
If you enter the wrong Fingerprint, Pincode, or RFID Card for 5 times within 5 minutes, the system will be locked for 90 seconds and cannot be unlocked within 90 seconds and there will be a voice prompt “System has been locked”.
The frozen state refers to inputting the incorrect combination of the Fingerprint, Pincode and RFID Card for 5 times in a row, the system will lock 90 seconds, during which the door can not be unlocked by Fingerprint, Pincode, or RFID Card.

BATTERY POWER DETECTION
When the battery voltage is lower than 4.8V, every time the panel lights up, it will give the voice prompts “battery power is low, please replace the battery in a timely manner”, and the panel’s low battery icon lights up.
This product can be placed in AA type battery, and 4 AA-type battery can support the normal use of the lock.